Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
3 results
Search Results
Now showing 1 - 3 of 3
Article Citation - WoS: 19Citation - Scopus: 19Processing of Polymer-Derived, Aerogel-Filled, Sic Foams for High-Temperature Insulation(Wiley, 2023) Zambotti, Andrea; Ionescu, Emanuel; Gargiulo, Nicola; Caputo, Domenico; Ahmetoğlu, Çekdar Vakıf; Santhosh, Balanand; Biesuz, MattiaPorous polymer-derived ceramics (PDCs) are outperforming materials when low-density and thermal inertia are required. In this frame, thermal insulating foams such as silicon carbide (SiC) ones possess intriguing requisites for aerospace applications, but their thermal conductivity is affected by gas phase heat transfer and, in the high temperature region, by radiative mechanisms. Owing to the versatility of the PDC route, we present a synthesis pathway to embed PDC SiC aerogels within the open cells of a SiC foam, thus sensibly decreasing the thermal conductivity at 1000 degrees C from 0.371 W center dot m(-1)K(-1) to 0.243 W center dot m(-1)K(-1). In this way, it was possible to couple the mechanical properties of the foam with the insulating ability of the aerogels.The presented synthesis was optimized by selecting, among acetone, n-hexane, and cyclohexane, the proper solvent for the gelation step of the aerogel formation to obtain a proper mesoporous colloidal structure that, after ceramization at 1000 degrees C, presents a specific surface area of 193 m(2)center dot g(-1). The so-obtained ceramic composites present a lowest density of 0.18 g center dot cm(-3), a porosity of 90% and a compressive strength of 0.76 MPa.Article Citation - WoS: 14Citation - Scopus: 16Microstructure and Mechanical Properties of A357/Sic Nanocomposites Fabricated by Ultrasonic Cavitation-Based Dispersion of Ball-Milled Nanoparticles(SAGE Publications Inc., 2017) Kandemir, SinanIn this work, A357/0.5 wt.% SiC nanocomposites were fabricated with a combination of ultrasonic processing and a nanoparticle feeding mechanism that involves the introduction of a closed end aluminium tube filled with the ball-milled SiC nanoparticles (20-30 nm) and aluminium powders (<75 μm) into the melt for complete deagglomeration and uniform dispersion of nanoparticles through the matrix. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicate that relatively effective deagglomeration and uniform dispersion of SiC nanoparticles into the molten alloy were achieved. The hardness and tensile properties of the nanocomposites were notably improved compared to those of the ultrasonically processed A357 alloy without reinforcement, showing the strengthening potency of nanoparticles and the good bonding obtained at the particle-reinforcement interface.Article Citation - WoS: 17Citation - Scopus: 26Thixoforming of A356/Sic and A356/Tib2 Nanocomposites Fabricated by a Combination of Green Compact Nanoparticle Incorporation and Ultrasonic Treatment of the Melted Compact(Springer Verlag, 2014) Kandemir, Sinan; Atkinson, Helen V.; Weston, David P.; Hainsworth, Sarah V.Thixoforming is a type of semi-solid processing which is based on forming metals in the semi-solid state rather than fully liquid or solid state. There have been no reports of the thixoforming of nanocomposites in the literature. The incorporation of ceramic nanoparticles into liquid metals is a challenging task for the fabrication of metal matrix nanocomposites due to their large surface-to-volume ratio and poor wettability. Previous research work by a number of workers has highlighted the challenges with the incorporation of nanoparticles into liquid aluminum alloy. In the present study, SiC and TiB2 nanoparticles with an average diameter between 20 and 30 nm were firstly incorporated into green compacts by a powder forming route, and then the compacts were melted and treated ultrasonically. The microstructural studies reveal that the engulfment and relatively effective distribution of the nanoparticles into the melt were achieved. The hardness was considerably improved with only 0.8 wt pct addition of the nanoparticles. The nanocomposites were successfully thixoformed at a solid fraction between 0.65 and 0.70. The microstructures, hardness, and tensile mechanical properties of the thixoformed nanocomposites were investigated and compared with those of the as-received A356 and thixoformed A356 alloys. The tensile properties of the thixoformed nanocomposites were significantly enhanced compared to thixoformed A356 alloy without reinforcement, indicating the strengthening effects of the nanoparticles.