Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
3 results
Search Results
Now showing 1 - 3 of 3
Article Citation - WoS: 12Citation - Scopus: 13A General Expression for the Stagnant Thermal Conductivity of Stochastic and Periodic Structures(The American Society of Mechanical Engineers(ASME), 2018) Bai, X.; Çelik, Hasan; Mobedi, Moghtada; Nakayama, AkiraA general expression has been obtained to estimate thermal conductivities of both stochastic and periodic structures with high-solid thermal conductivity. An air layer partially occupied by slanted circular rods of high-thermal conductivity was considered to derive the general expression. The thermal conductivity based on this general expression was compared against that obtained from detailed three-dimensional numerical calculations. A good agreement between two sets of results substantiates the validity of the general expression for evaluating the stagnant thermal conductivity of the periodic structures. Subsequently, this expression was averaged over a hemispherical solid angle to estimate the stagnant thermal conductivity for stochastic structures such as a metal foam. The resulting expression was found identical to the one obtained by Hsu et al., Krishnan et al., and Yang and Nakayama. Thus, the general expression can be used for both stochastic and periodic structures.Article Citation - WoS: 32Citation - Scopus: 38Fully Developed Forced Convection in a Parallel Plate Channel With a Centered Porous Layer(Springer Verlag, 2012) Çekmer, Özgür; Mobedi, Moghtada; Özerdem, Barış; Pop, IoanIn this study, fully developed heat and fluid flow in a parallel plate channel partially filled with porous layer is analyzed both analytically and numerically. The porous layer is located at the center of the channel and uniform heat flux is applied at the walls. The heat and fluid flow equations for clear fluid and porous regions are separately solved. Continues shear stress and heat flux conditions at the interface are used to determine the interface velocity and temperature. The velocity and temperature profiles in the channel for different values of Darcy number, thermal conductivity ratio, and porous layer thickness are plotted and discussed. The values of Nusselt number and friction factor of a fully clear fluid channel (Nu cl = 4. 12 and fRe cl = 24) are used to define heat transfer increment ratio (ε th = Nu p/Nu cl)and pressure drop increment ratio (ε p = f Re p/f Re cl) and observe the effects of an inserted porous layer on the increase of heat transfer and pressure drop. The heat transfer and pressure drop increment ratios are used to define an overall performance (ε = ε th/ε p) to evaluate overall benefits of an inserted porous layer in a parallel plate channel. The obtained results showed that for a partially porous filled channel, the value of ε is highly influenced from Darcy number, but it is not affected from thermal conductivity ratio (k r) when k r > 2. For a fully porous material filled channel, the value of ε is considerably affected from thermal conductivity ratio as the porous medium is in contact with the channel walls.Article Citation - WoS: 17Citation - Scopus: 21Effects of Particle Size and Electrical Resistivity of Filler on Mechanical, Electrical, and Thermal Properties of Linear Low Density Polyethylene-Zinc Oxide Composites(John Wiley and Sons Inc., 2013) Özmıhçı Ömürlü, Filiz; Balköse, DevrimThe effects of particle size and electrical resistivity of zinc oxide (ZnO) on mechanical properties, electrical and thermal conductivities of composites made with linear low density polyethylene (LLDPE) were investigated. Micron sized (mZnO), submicron sized (sZnO), and nano sized (nZnO) powders having resistivities of 1.5 × 106, 1.5 × 109, and 1.7 × 108 were used to prepare composites with 5-20 vol % filler. The tensile strength was lowered and the modulus of elasticity of the composites was increased with ZnO addition. Rather than the particle size of the ZnO, its initial resistivity and aspect ratio affected the resistivity of composites. The resistivity of the LLDPE was lowered from 2.3 × 1016 Ω cm down to 1.4 × 1010 Ω cm with mZnO addition. Thermal conductivity of the composites was increased with ZnO addition 2.5-3 times of the polymer matrix. The composites can be used for electrostatically dissipating and heat sink applications due to their decreased electrical resistivity and increased thermal conductivity.