Master Degree / Yüksek Lisans Tezleri
Permanent URI for this collectionhttps://hdl.handle.net/11147/3008
Browse
41 results
Search Results
Master Thesis Sb2se3 Absorber Layered Solar Cell Fabrication and Characterization(01. Izmir Institute of Technology, 2021) Kurtuldu, Seher Hazal; Aygün Özyüzer, Gülnur; Tarhan, EnverThin-film antimony selenide (Sb2Se3) solar cells have gained attention as a high-potential photovoltaic technology around the world. Outstanding features like a high absorption coefficient, a suitable direct bandgap, and good hole mobility make Sb2Se3 a promising absorber material for solar cell applications. It has demonstrated a very rapid growth reaching 9.2% power conversion efficiency (PCE) in only 7 years after intensive studies. In the present thesis, first of all Sb2Se3 thin films were deposited on soda lime glasses (SLGs) and investigated using energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), scanning electron microscopy (SEM), spectrophotometry and Raman spectroscopy. Structural and optical studies were carried out depending on the thickness, used argon (Ar) gas flow rate and post-annealing temperature of the Sb2Se3 films in order to optimize the absorber layer to be used in solar cell. This study revealed that key parameters such as band gap energy and crystal structure of the Sb2Se3 thin films affected by the thickness, Ar gas flow rate during deposition and post-annealing temperature. In addition, oxide phase formation was also found to be related to these growth parameters. Finally, SLG/ITO/Zn(O,S)/Sb2Se3/Ag for superstrate configuration and both SLG/Mo/Sb2Se3/CdS/ITO and SLG/Mo/Sb2Se3/CdS/ZnS/ITO devices fabricated for substrate configuration solar cells. Since Zn(O,S)/Sb2Se3 heterojunction has not been studied before in the literature, this study will be the first. At the end of the electrical analysis, the best conversion efficiency of 3.9% was achieved by the solar cell with the substrate configuration.Master Thesis Development of Conductive Oxide Based Thin Film Modified Electrodes and Biosensors Applications(Izmir Institute of Technology, 2021) Yurttaş, Betül; Özyüzer, Lütfi; Erdem Gürsan, Kadriye ArzumFrom the first biosensor produced in 1956 to the present day, biosensors have been highly developed and diversified. In biosensor manufacturing, thin films have become a rapidly emerging field. Depending on the thin film material used, thin films have many advantageous properties for biosensors, such as high surface-to-volume ratio, conductivity, stability, specificity, biocompatibility, and good electrocatalytic activity. Dopamine is a neurotransmitter that has a significant impact on the emergence and treatment of certain diseases such as Alzheimer's and Parkinson's diseases. Dopamine monitoring is important for the prevention of these diseases, and it is a favorable option to use biosensors, which are useful and practical tools, instead of time-consuming and expensive conventional methods. For this purpose, in this thesis, a non-enzymatic electrochemical biosensor based on thin film electrodes was developed for monitoring dopamine levels. The electrodes were developed by deposition of Zn2SnO4 (ZTO) thin film on ITO thin film substrate by DC magnetron sputtering technique. The properties of the electrodes were determined by thickness, optical transmittance, XRD and SEM analysis. Electrochemical analysis, namely CV, EIS and DPV measurements, were performed before and after the electrodes were sonicated and modified with APTES before their application to the voltammetric detection of dopamine. In addition, electrochemical measurements were performed before/after sonication, APTES modification. Dopamine was detected by a voltammetric method using DPV technique. Furthermore, experiments in the presence of interferents such as ascorbic acid (AA), uric acid (UA) etc. showed that the thin film electrodes can be successfully applied for voltammetric determination of dopamine. As a result, the biosensor technology developed in this study has the potential to be wearable in the future, enabling non-invasive monitoring of dopamine levels in body fluids such as saliva, tears and sweat.Master Thesis The Growth of Vanadium Dioxide Thin Films by Magnetron Sputtering Technique and Terahertz Wave Modulation Characteristics(01. Izmir Institute of Technology, 2020) Ata, Bengü; Özyüzer, LütfiVanadium dioxide (VO2) is a fascinating material thanks to its unique insulator-metal transition (IMT) at 68 °C which is very close to the room temperature. This reversible change in electrical resistivity is around several orders of magnitude and the electrical change accompanied by optical and structural change as well. Thanks to these unique properties vanadium dioxide material has been studied intensively past decades. This phase transition allows us to apply the transition properties widen application such as field effect transistor (FET), uncooled bolometers, tunable metamaterial filters, high data rate wireless communication etc. Especially for terahertz region which is the most unexplored region of the electromagnetic spectrum, vanadium dioxide is a promising material having ability to modulate terahertz waves by IMT phenomena. In this work, vanadium dioxide (VO2) thin films fabricated by reactive DC magnetron sputtering method and its properties optimized to minimize the amounts of secondary phases by optimizing the oxygen concentration, sputtering power and deposition time. Samples which show the maximum resistivity change during the transition have been used for the terahertz modulation experiments. It has been observed that when the VO2 samples triggered by continuous wave (CW) laser, VO2 transforms to the metallic phase, behave as an opaque material to the terahertz wave. At room temperature, in insulating phase it is partially transparent to terahertz radiation. This results indicate that VO2 thin films can be a good candidate for THz wave modulators.Master Thesis Manufacturing and Characterization of Perovskite Thin Films Using Novel Methods(Izmir Institute of Technology, 2020) Bıyıklı, Ozan; Sarı, Emre; Tekin, Hüseyin CumhurPerovskite photovoltaics is a promising technology due to its low-cost fabrication and high efficiency. Since their first demonstration in 2009, efficiencies of perovskite solar cells (PSCs) increased unprecedently fast from 3.81% to 25.2% in 10 years. The most common method for the deposition of the absorber layer of the perovskite solar cells is the spin-coating method, which is not a scalable method, and this method is an obstacle to their commercialization. Efficiencies obtained with scalable methods are currently lower than that of the spin-coating method. In this thesis, among the scalable deposition methods, a novel ultrasonic spray-coating was used by adding antisolvent vapor to the system. The antisolvent quenching technique, that is commonly used to improve the crystalline quality of the film by spin-coating was successfully adapted for ultrasonic spray coating. The interaction between diethyl ether (DE) vapor, which is used as an antisolvent, and MAPb(I(3-x)Brx)3 precursor solution (where the solvent is DMF:DMSO, 4:1) was utilized to improve the crystalline quality of the perovskite film. As a result of this interaction, the intermediate phase was observed. The transition to the intermediate phase is supported by data from characterization methods such as optical microscopy, scanning electron microscopy (SEM), X-Ray diffraction (XRD), and current-voltage measurement. Furthermore, n-i-p devices with the FTO/c-TiO2/m-TiO2/MAPb(I(1-x)Brx)3/Spiro-OMeTAD architecture were produced with different antisolvent vapors and their efficiencies was compared. It was observed that devices using DE vapor reach higher efficiencies than devices without any antisolvent vapor.Master Thesis Anti-Reflective and Optical Transparent Coatings for Thin Film Solar Cells and Glasses(Izmir Institute of Technology, 2020) Kamolov, Shukrullo; Özyüzer, Lütfi; Özyüzer, LütfiAntireflective coatings in some implementation necessary for the decreasing surface reflection, but in some applications also for increasing transmittance. Incident radiation on the surface of the optical material is divided into transmitted, reflected, scattered, and absorbed proportions, and the proportion of current energy that deployed among them is defined by RI (refraction indices). Solar panels made from crystalline or polycrystalline silicon, but another type of solar panel is a thin-film solar panel. Thin-film technology has several advantages, such as low material consumption, which leads to cost savings to production, the ability to absorb diffused solar radiation, a relatively high efficiency (up to 20%), long service life (efficiency decreases by 10-15% of the initial efficiency). For all types of photovoltaic devices, energy loss is an important issue. Single-layer and two-layer antireflection coatings with a low refractive index, coated and uncoated (SiO2) thin-film with the sol-gel method were prepared and compared in terms of performance and continuity. The photocatalytic performance of (SiO2) thin films in 1, 2, 3, 4, 5 and 24 hours was defined with methylene blue dye solution (20 mL) under UV source and was illuminated by it. The I-V characteristics curve of solar cells for small and large area was learned and increasing efficiency was observed. Adhesion tests in this study was applied by tape tests on substrates of glass. As a result, the field tests of small and large area glasses coated solar panels were realized, the low reflectance and high efficiency were obtained.Master Thesis The Effect of Metal Doping on Tio2 for Photocatalytic Applications(Izmir Institute of Technology, 2019) Alduran, Yeşim; Özyüzer, Lütfi; Öztürk, OrhanRecently, the photocatalysis method has been an active research area as a promising solution for environmental cleaning method, leading to self-cleaning and sterilization of solar cell surfaces to produce water dissociation reaction. Titanium dioxide (TiO2) is the most suitable semiconductor for photocatalytic applications due to its high oxidation potential and high efficiency when irradiated by ultraviolet light (UV). Undoped and Ruthenium (Ru+) doped TiO2 thin films were prepared using magnetron sputtering technique. All thin films were grown on SLG different ratios like 1 sec, 3 secs, 5 secs and 7 secs to set shutter position in magnetron sputter target. Transparent substrate SLG is coated with nearly 50 nm TiO2 thin films without compromising any optical properties. Samples were heat treated for two hours at 500°C to get the anatase phase crystal structure. The crystallization peaks of TiO2 are proved to get the anatase phase. Photocatalytic activity of TiO2 thin films are determined after 1, 3, 5 and 24 hours with organic pollution as a methylene blue dye degradation under UV light. The degradation of methylene blue was investigated kinetically and photocatalytic activity rate constants of the photocatalysts were calculated. All thin films could not reach super hydrophilicity state. Undoped TiO2 contact angle 47.309o and Ru doped TiO2 63.218o were evaluated. The photocatalytic degradation percentage of Methylene Blue was reached 87%, after 24 hours of UV irradiation, when using Ru-doped TiO2 thin film. Consequently, the anatase phase of Ru-doped TiO2 thin films are found best photocatalytic activity in self-cleaning performance.Master Thesis Optical Characterization of Nanoscale Dielectric Films on Curved Surfaces Using Near Field Diffraction Method(Izmir Institute of Technology, 2019) Ataç, Enes; Dinleyici, Mehmet SalihDemand on the high-quality optical thin films has increased because of the importance in the optical sensor technologies. The thicknesses of such films are usually shorter than the wavelength of visible light. Therefore, the optical characterization of these films is not a routine procedure especially on curved surfaces such as optical fiber. Besides, the methods in the literature and commercially available systems are either expensive, destructive or non-real time. In this thesis, it is aimed to propose a simple, inexpensive and non-destructive optical characterization method of nano-scale dielectric films on curved surfaces. The methodology of that approach can be described as the near field wavefront tracing diffraction by using structured light. In this way, it has been shown that sub-wavelength film thicknesses can be estimated. The proposed diffraction method is organized in four main stages. These are the coating of optical fibers, generation of structured light, determination of wave propagation via the near field Huygens-Fresnel wave-front tracing and sensing and processing of signal from the sensor array. Layer by layer assembly technique is used in coating process to keep under control the thickness of transparent film. Selection of various source types is about to changing of point spread function of applied field and observe the effects on intensity pattern. Using near field diffraction technique, sub-wavelength thickness of thin films can be predicted by taking the higher order components of diffraction pattern by recording at very close proximity to object. In this way, determination of thickness beyond the diffraction limits can be realized. Furthermore, the resolution of sensor array in sensing part is important since pixel size of the sensor array determines your detection limits to catch all variations on diffraction pattern. The whole process has a mathematical model with numerical analysis methods. This dissertation is about the proposing a mathematical estimation model for the optical properties of nano-scale dielectric films coated on curved surfaces. The experimental results show that near field Huygens-Fresnel wave-front tracing method by using structured light is a powerful technique.Master Thesis Growth and Characterization of Znsno Thin Films on Polymers for Oleds(Izmir Institute of Technology, 2019) Ekmekçioğlu, Merve; Aygün Özyüzer, GülnurThe use of flexible organic light-emitting diodes (OLEDs) in smartphones and televisions with inclined screen shows significant improvements in commercial applications. Recently, flexible OLEDs have been used in lightweight, portable, wearable and even deformable screens, sensors as well as solid-state lighting applications. Under favour of these applications, remarkable developments are observed in the production of flexible electronics. The advantages of OLEDs according to the existing liquid crystal display (LCD) technology are self-emission capability, wide viewing angle, fast response time, simple structure, and low driving voltage. Highly conductive and transparent anodes are required for efficiency and uniform light emission in OLEDs. Indium tin oxide (ITO) which is one of the most promising anodes among transparent conductive oxides (TCO), has superior electrical and optical properties such as ~85% high transmittance at the visible region and ~104 Ω−1 cm−1good conductivity. The reason is due to the bandgap range of about 3.70 eV. Zinc tin oxide (ZnSnO or ZTO) is another TCO commonly used for many applications in the literature. Alternative anodes eliminate the use of ITO due to the absence of indium element so that highly desirable. In this thesis, ZTO is used as anode instead of ITO thin film and the eligibility of ZTO as an anode in OLED production is explored. The advantages of the optimized ZTO thin film according to the ITO are that is abundant on earth, has better performance, has low surface resistance, has less surface roughness, is capable of being produced as an anode in OLEDs. In this thesis to be successful, at the first stage ZTO thin films have grown on soda lime glass by magnetron sputtering, then ZTO and ZTO/Ag/ZTO multilayer thin films respectively have been deposited on flexible Polyethylene terephthalate (PET) and Polyimide (PI) substrates by magnetron sputtering method. In this way, the best coated thin films have been investigated using spectrophotometry, energy-dispersive X-ray spectroscopy (EDS), scanning electron microscopy (SEM), Xray diffraction (XRD) and Raman spectroscopy.Master Thesis Improvement of Transparent Conductive Hybrid Ito/Ag Electrodes by Electro-Annealing(Izmir Institute of Technology, 2019) Uyanık, Zemzem; Aygün Özyüzer, GülnurHibrit ITO/Ag/ITO (IAI) ince film tabaka yapılarının optik ve elektriksel performansları, ITO ve Ag katmanı kalınlığının fonksiyonu olarak incelenmiştir. Hibrit IAI ince filmleri borosilikat cam üzerine oda sıcaklığında yüksek vakum altında dc mıknatıssal saçtırma yöntemi ile üretilmiştir. Hibrit yapıdaki ITO, Ag, ITO filmlerin kalınlığı düşük tabaka direncine ve yüksek optik geçirgenliğe sahip olacak şekilde ayarlanmıştır. ITO katmanları arasındaki gömülü metal Ag katmanı, 10 nm ile 25 nm arasında değişen kalınlıklarda kullanılmıştır. IAI tabakası analiz edildikten sonra IAI ince filmlerin kristalliğini iyileştirmek için elektro-tavlama uygulanmıştır ve elektrik akımının IAI ince filmler üzerindeki etkisinin araştırılmasıyla elektronik cihaz ömrünün arttırılması amaçlanmıştır. Elektro-tavlamanın endüstriyel uygulamalar için daha uygun bir teknik olduğu sonucuna varılmıştır. IAI ince filmin yüzey direnci elektro-tavlama işleminden sonra 8.7 Ω/□ olarak bulunmuştur en yüksek geçirgenliğe ise 88.9% da ulaşılmıştır. Hibrit IAI ince filmlerin optoelektronik özellikleri, ITO film kristalliğini etkileyen ara katman olan metal Ag kalınlığına bağlıdır. Hibrit IAI ince filmlerinin yapısal özellikleri, CuK����� radyasyonuna sahip (�����=0.154 nm) X-ışını kırınımı (XRD) (Philips X'Pert Pro) ile tavlama sıcaklığının fonksiyonu olarak karakterize edilmiştir. IAI ince filmlerinin morfolojisi hakkında bilgi taramalı elektron mikroskobu (SEM) ile elde edilmiştir. IAI ince filmin optik geçirgenliği 200-2600 nm dalga boyu aralığına sahip PerkinElmerLambda 950 UV/Vis/NIR Spektrofotometre ile ölçülmüştür. Yüzey direnci ölçümleri için Keithley 2424 kaynak metrisi kullanılarak dört nokta yöntemi uygulanmıştır.Master Thesis Efficiency Studies of Cu2znsns2 Thin Film Solar Cell(Izmir Institute of Technology, 2018) Meriç, Ece; Özyüzer, Lütfi; Aral, GürcanCu2ZnSnS4 (CZTS) is a promising candidate as an absorber layer for thin film solar cells due to not only its low cost but also nontoxic properties contrary to alternative materials such as CdTe and Cu(In,Ge)Se2 (CIGS). Recently, CZTS and similar chalcogenides have attracted remarkable attention because of their suitable properties. In my thesis; I studied the efficiency of Cu2ZnSnS4 thin film solar cells for various stoichiometric cases. Besides, the effect of back contact, buffer layer thickness and sulfurization time were investigated. CZTS thin films were fabricated by DC magnetron sputtering method on Molybdenum (Mo) coated Soda Lime Glass (SLG) and Ti foil substrates. Cu, Sn, Zn, Cu layers were, respectively, deposited on the substrates, and then sulfurization process was followed as the second step in the growth process to obtain a desirable CZTS formation. The as grown CZTS structure was investigated using Raman and X-Ray Diffraction (XRD) spectroscopies. Scanning electron microscopy (SEM) was used to investigate the surface morphology of the films. Energy dispersive spectroscopy (EDS) was used to define the chemical structure of the surface of the films. Next, a CdS buffer layer was deposited on CZTS absorber layer using CBD method at 85oC for varying times (60, 75 and 90 min). Then, ZnO and Al doped ZnO (AZO) layers were deposited on CdS. J-V curves were obtained for SLG/Mo/CZTS/CdS/ZnO/AZO solar cell structure. The photovoltaic characteristic of solar cells was studied and their dependence on CdS deposition time were found. Among all the device we produced, the highest efficiency was obtained for the device with the lowest CdS deposition time. In addition; effect of sulfurization time on the solar cell conversion efficiency was studied.