Master Degree / Yüksek Lisans Tezleri
Permanent URI for this collectionhttps://hdl.handle.net/11147/3008
Browse
8 results
Search Results
Master Thesis Esterification of oleic acid with methanol on structured solid acid catalysis(01. Izmir Institute of Technology, 2024) Büyükkapancı, Yunus; Şeker, ErolBu çalışmada, Oleik Asit metanol ile birlikte Sülfonlanmış Alüminyum Silika (SAS) heterojen asidik katalizörü üzerinde gerçekleştireceği esterifikasyon reaksiyonu incelenecektir. Araştırma, farklı metanol/yağ asidi mol oranları (9/1-21/1), katalizör miktarları (%10-%20) ve reaksiyon sürelerinin (3s–9s) 105°C sıcaklıkta reaksiyon verimliliği üzerindeki etkisini Box Bhenkhen yardımı ile değerlendirmeyi amaçlamaktadır. Katalizörlerin aktivitesi iki farklı katalizör formu (toz, yapısal) ele alınarak değerlendirilecektir. Bu çalışma, varyans analizi istatistiksel sonuçlarına göre, toz katalizör varlığında gerçekleştirilen deneylerde reaksiyon süresinin dönüşüm değerleri üzerinde en büyük etkiye sahip olduğunu göstermektedir. Reaksiyon süresi uzadıkça dönüşüm oranları hızlı bir şekilde artmıştır. Ayrıca, kullanılan katalizör miktarı da doğrudan etkili olmuş ve en yüksek dönüşüm oranı, Alkol/FFA oranının 9/1 olduğu durumda elde edilmiştir. Ayrıca, yapısal katalizörlerin varlığında gerçekleşen reaksiyonun dönüşüm değerinin, toz formundaki katalizörlerin değerleriyle karşılaştırılabilir olduğu tespit edilmiştir. Ayrıca yapılandırılmış katalizörlerde toz katalizöre göre ayırma adımına gerek kalmamıştır.Master Thesis Esterification of Free Fatty Acid Obtained From Waste Cooking Oil Over Solid Catalyst(Izmir Institute of Technology, 2022) Karacasulu, Cem; Şeker, Erol; Şeker, ErolThe objective of this study was to investigate effect of reaction temperature, catalyst weight percentage and composition of Al2O3/SiO2 on conversion of FFA obtained from waste cooking oil (WCO) to take place esterification reaction by using Box-Behnken design. Statistical analysis demonstrates that catalyst weight percentage and temperature were insignificant statistically. Alumina composition was found as significant parameter at certain conditions by considering statistical analysis. It was seen that conversion of Free Fatty Acid (FFA) increases as composition of Al2O3 in Alumina/Silica catalyst increases. %80 Al2O3/20% SiO2 catalyst was found as promising catalyst since conversion of FFA with the catalyst was 32% at 80°C and 15:1 alcohol to FFA ratio. Besides, it was found that alcohol to FFA ratio affected the conversion reversely. When alcohol to FFA ratio was reduced to 2:1, conversion of FFA increased to 41%. The prepared catalysts were characterized by XRD and TPD analysis. Activity of catalysts were attributed to acidic strength and Bronsted acid sites on the aluminum sulfate in the catalysts. After screening effects of catalysts and reaction conditions, optimum levels of parameters were used to investigate the esterification reaction of model WCO. This reveals that conversion of FFA was found as 11% at 80°C and 15:1 alcohol to FFA ratio. Finally, the proposed catalyst does not have catalytic activity of hydrolysis reaction of oil at applied conditions.Master Thesis Butyl Esters Production From Canola Oil Over Heterogeneous Base Catalysts(01. Izmir Institute of Technology, 2021) Akın, Oğuzhan; Akın, Oğuzhan; Şeker, Erol; Şeker, ErolIn this study, transesterification reaction of canola oil with butanol over calcium oxide alumina catalyst was investigated with varying butanol:lipid molar ratios, catalyst amount and reaction time. Catalysts were prepared with the single step sol-gel method, and the activity of synthesized catalysts were investigated for two different forms of catalysts as powder and structured form. In the case of powdered catalysts, at butanol:lipid molar ratios of 9 and 24 with 6 wt% of lipids as catalyst amount, leaded 32% and 45% butyl esters yield in 1 hour. On the other hand, ~70% butyl esters yield has obtained at butanol:lipid molar ratios of 48 and 60 for the reaction time of 1 hour, while 89% yield had achieved when the reaction lasted for 4 hours at butanol:lipid molar ratio of 48. The necessity of mild basic strength and high butanol:lipid molar ratio was found to obtain high butyl esters yield. At high butanol lipid ratios of 48 and 60, it was observed that glycerolysis reaction occurs and promotes reverse transesterification reactions in first 30 minutes of the experiments. In the case of structured catalysts, lower butyl esters yields than powder catalysts were obtained, yet they eliminated the need for catalysts separation step in the experiments. Reusability tests showed that catalyst activity has decreased due to calcium ion leaching in the first hour of reaction and kept its activity constant for the rest of the reaction.Master Thesis Carbon Dioxide Hydrogenation on Alumina Supported Ruthenium Catalysts(Izmir Institute of Technology, 2019) Hamza, Gökmen Oğuzcan; Şeker, ErolIn this study the effect of basicity of catalyst is investigated using different metal oxide supported Nickel and Ruthenium catalyst. The basic strength of catalysts was orchestrated with using different types of metals and different composition of supports. In this study Al2O3-CaO, Al2O3-MgO, Al2O3-BaO supports were used with nickel and ruthenium catalyst, which synthesized with sol-gel method. Different mass ratios of supports were used such as; 100%, 70%/30%, %50/50%, 20%/80% respectively. For all metal oxides Nickel loadings are 1 %, 5% and Ruthenium loading is 0.5%. Calcination temperature was 500 0C with 6 hours. All catalysts were used in methanation reaction with conditions varies between 300-600 0C, inlet ratio of CO2/H2 1/4 to 1/6 and GSHV 5000h-1/10000h-1. The products were analyzed using GC and catalysts were analyzed using XRD NH3-TPD and BET. Nickel load selected as 1%, magnesium supported catalysts' the main crystallites were aluminum oxide and magnesium oxide for 30%,50%,80; respectively. Calcium supported catalyst had had alumina and calcium oxide crystallites for 30%,50% respectively. Barium supported catalysts had had alumina and barium mix oxide crystallites for 30%,50% respectively. For 5% Nickel loaded 70-30% alumina magnesia mix oxide catalyst magnesia and alumina crystallites are found. Aluminum magnesium mix oxide catalysts had higher basicity than aluminum barium mix oxide catalysts for 1% nickel catalysts. Ruthenium based magnesium alumina mix oxide catalyst had higher basicity than nickel-based magnesium alumina catalysts. Ruthenium catalysts had higher total performance towards both of the reverse water gas shift reaction and carbon dioxide methanation than nickel-based catalysts.Master Thesis Development of Kinetic Model for Industrial Ethylene Oxide Catalyst by Using Model-Targeted Experimentation Approach(Izmir Institute of Technology, 2019) Sarrafi, Şahin; Şeker, Erol; Arkun, Ziya YamanEthylene oxide (EO) is produced via selective oxidation of ethylene with oxygen using a Ag supported on -Al2O3 catalyst. The ethylene epoxidation reaction is desired, whereas the ethylene and EO combustion reactions are not. Proposed study is aimed at developing a tailor-made kinetic model in order for making use in the industrial ethylene oxide reactors which are of paramount importance from the viewpoint of process economics and the greenhouse gas (GHG) induced various environmental exposures. With aging of the catalyst, the trade-off between selectivity and productivity becomes gradually more prominent. Along with the compensation of loss of active sites under the favor of increasing of the temperature, catalyst still provides sustainable commercial yields at the expense of excess feedstock consumption which in turns leads to boost GHG emissions by releasing more carbon dioxide (CO2) into the atmosphere. To maintain catalyst activity for a longest period possible, controlling process variables more preciously with a robust model is very demanding issue throughout the last two decades. Within the scope of this thesis, model-targeted experimentation approach was used assisting by gPROMS software in determining intrinsic kinetics of the commercial catalyst in use through integral reactor coupled with gas chromatography. During the course of the kinetic experiments, the effect of VCM used as a promoter together with inhibiting effects of product gases such as CO2 and EO were also investigated and included into the kinetic model to be derived.Master Thesis Catalytic Surface Coatings for Household Ovens(Izmir Institute of Technology, 2016) İzer, Alaz; Şeker, Erol; Şeker, ErolThe emission of harmful volatile compounds, such as aldehydes, and also carbon monoxide could occur during cooking processes at home or industry due to the combustion and cracking of spilled vegetable oil on the walls of an oven. It is known that the by-products generated during cooking could affect human health and environment if they are properly vented or removed. To eliminate the health and environmental problems related to oven emission, self-cleaning catalytic materials coated walls for ovens seem to be viable alternative to the toxic and time consuming chemical cleaning solutions. In this project, a sol-gel method and also the dip coating technique was used to produce a catalytic material coated aluminum plates. Specifically, the calcination time and the temperature were studied to better understand the relationship between the textural/chemical properties of the catalyst coated metal plates and their catalytic activities. The studied calcination temperatures were 450°C, 500°C and 550°C whereas the calcination time were 10 min, 30 min and 60 min for each type of catalyst. Aluminum oxide supported nickel and also aluminum oxide - manganese oxide supported nickel catalysts were prepared as the catalyst that were used in coating. The catalytic activities of the catalyst coated plates were determined using canola oil as a function of reaction time which were 1h at 170°C and 200°C. The results have been shown that the most convenient calcination conditions for the canola oil combustion were 500°C for 30 minutes by using aluminum oxide – manganese oxide supported nickel catalyst.Master Thesis Biodiesel Production From Safflower Using Heterogeneous Cao Based Catalysts(Izmir Institute of Technology, 2012) Yalman, Emir; Şeker, Erol; Şeker, ErolIn this study, the activities of heterogeneous mixed oxide catalyst; calcium oxide on alumina was investigated in the transesterification of canola and safflower vegetable oils to produce biodiesel, i.e. methyl esters. The primary goal of this study is to understand the effect of calcination temperature and calcium oxide (CaO) loading on the conversion activity of calcium oxide on alumina in the transesterification of canola and safflower vegetable oils. The mixed oxide catalyst was prepared by a modified single step sol-gel method. Calcium oxide was chosen because of its well known basic property. This study shows that calcium oxide on alumina catalysts having high CaO dispersion, calcined at high temperature, gave high biodiesel yields even under the reaction conditions, such as low reaction temperature, 50 °C, 9 of methanol/Oil molar ratio, 6 wt. % of catalyst/oil, and also short biodiesel reaction time, such as 4 – 10 minutes in the transesterification of safflower and canola oils. Also, it was observed that 70% CaO/Al2O3 catalyst when calcined at 700 °C was the most active catalyst among all the catalysts prepared in this study. Moreover, the reusability of CaO/Al2O3 demonstrated that ~20 – 250 ppm of Ca was lost during the reaction and the amount of Ca cation leaching depended on the reaction time, CaO loading and the calcination temperature. Also, it was found that Ca cation loss occurred during the reaction did not hinder the activity of the catalysts, which was found by the reusing the catalysts for couple times. Besides, when the biodiesel yield was higher than 70%, the system was influenced by external mass transfer limitation.Master Thesis Oxidation of Ethanol and Carbon Monoxide on Alumina-Supported Metal/Metal Oxide Xerogel Catalysts(Izmir Institute of Technology, 2011) Ateş, Selcan; Şeker, ErolThe main goal of the study is to investigate the effect of metal type, metal oxide type and metal/oxide loading on the conversion as a function of temperature for the complete combustion of ethanol and CO in air over single step sol-gel made Al2O3 supported metal and mixed metal oxides. Two types of catalysts, Pt/Al2O3 (1, 2, and 3 % Pt loaded) and CuO-Mn2O3/Al2O3, with Cu/Mn molar ratio of 1:1, 5:1 and 12:1, and 50, 70, and 90% metal loading, were synthesized by impregnation and single step sol-gel methods, respectively. In addition, by synthesizing CuO/Al2O3, Mn2O3/Al2O3 and Pd-Mn2O3/Al2O3, the catalytic activity relationship between metal and metal oxides were clarified. Characterization of the samples was performed by XRD, BET, and FT-IR techniques and it was observed that among the metal oxide catalysts, CuO-Mn2O3/Al2O3 (70 wt%; (Cu/Mn)molar=1) showed the highest activity due to the formation of Cu1.5Mn1.5O4 phase while 3% Pt loaded alumina was the catalyst demonstrated the highest catalytic activity among the noble metal catalysts. Also, Pd addition enhanced the activity of metal oxide catalyst by lowering the temperature at which ~99% ethanol conversion was obtained. Moreover, deactivation of CuO-Mn2O3/Al2O3 mixed oxides was observed due to the irreversible adsorption of CO2 on catalyst surface at low temperatures. Except for Pt containing catalysts, the catalysts that showed high catalytic activity in ethanol oxidation was also tested for CO oxidation and CO2 formation was detected qualitatively at varying operating temperatures.