Master Degree / Yüksek Lisans Tezleri

Permanent URI for this collectionhttps://hdl.handle.net/11147/3008

Browse

Filters

2014 - 20176

Settings

Author: search.filters.author.Ebil, ÖzgençPublisher: search.filters.publisher.Izmir Institute of Technology

Search Results

Now showing 1 - 6 of 6
  • Master Thesis
    Effects of Grid Design on Lead-Acid Battery Performance
    (Izmir Institute of Technology, 2017) İşler, Tuğçe; Top, Ayben; Ebil, Özgenç; Ebil, Özgenç; Top, Ayben; 03.02. Department of Chemical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of Technology
    In today’s world, approximately 88 percent of the total energy demand is supplied by fossil fuels; however, it has become clear that; other energy sources are needed due to limited fossil fuels. The demand for energy can most effectively be filled by renewable energy sources as installed energy storage capacity is growing rapidly. If renewable energy sources advance enough to fulfill the high demand, earth-friendly, clean and sustainable energy will help to protect the environment, thus ensuring a healthier life for future generations. Energy storage systems are essential in this endeavor, and in order to become more prevalent, storage systems for renewable energy sources must supply electricity without interruption as much as possible. As an electrochemical storage, a battery with a high level of performance, high energy density and life cycle could offer a viable solution for electricity storage provided that battery cost should be economically viable. This thesis aims to improve the geometry of the grid used in lead acid batteries in order to obtain a more uniform current and potential distribution, and minimize the potential drop for improved battery performance. A 3D mathematical model was developed using finite element method to evaluate the behavior of the grid under various conditions. Five different porous grid geometries were simulated under different loads and optimum grid geometry was identified. The 3D mathematical model of the lead-acid battery based on finite element method was simulated under certain conditions in order to evaluate the effect of grid geometry on battery performance.
  • Master Thesis
    3d-Printed Multiprobe Analysis System for Solar Fuel Research; Design, Fabrication and Testing
    (Izmir Institute of Technology, 2016) Harmanlı, İpek; Karabudak, Engin; Ebil, Özgenç; Karabudak, Engin; Ebil, Özgenç; 04.01. Department of Chemistry; 03.02. Department of Chemical Engineering; 03. Faculty of Engineering; 04. Faculty of Science; 01. Izmir Institute of Technology
    Methods of generating electricity with unlimited, clean and cheap energy from solar energy are tried to be investigated and developed in practical and theoretical academic fields. Especially, photocatalytic water splitting (PWS) systems have been identified as the main method in this study as well as in many studies due to the advantages provided by production of solar fuels from water. In this research, a study was carried out on the alternatives of the both used experimental set-up and used photocatalytic material for PWS systems. A study has been carried out on both the used experimental setup and the used photocatalytic material alternatives in PWS systems. As an alternative experimental setup that allows small volume analysis for PWS by Unisense gas microsensors, a mini photoreactor was designed using 3-D drawing and printing techniques and its usability was tested for PWS applications. Moreover, some characterization results for the electronic band structure and the band gap of the lead (II) trioxovanadate (V) chloride [PbVO3Cl] crystal, which was discovered by Eanes and co-workers in 2007 at IZTECH, was introduced in this study by not only theoretical (DFT approximations; LDA, GGA and HSE06) but also experimental (XRD, Diffuse Reflectance Method- Tauc Plot, Raman Spectroscopy, Four Probe) methods. Also, its estimated theoretical price and its potential for future application in tandem solar fuel device as a photoanode in combination with Si photocathode was calculated and discussed. The results showed that the designed mini photoreactor system is an open to development apparatus that is suitable for PWS, besides, PbVO3Cl has an "indirect transition" band structure and a band energy of ~ 2.2 eV. Although it did not give an effective result in PWS applications done by the designed mini photoreactor, it can be said that it is a semiconductor which is worth studying and developing in detail for other researches in this field due to the compatibility of its band energy amount and optical properties for PWS.
  • Master Thesis
    Fabrication of Polymeric Nano-Coatings Via Chemical Vapor Deposition
    (Izmir Institute of Technology, 2016) Kırköse, Sema; Ebil, Özgenç; Ebil, Özgenç; 03.02. Department of Chemical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of Technology
    Thin film coatings are used to provide protection to the substrate of interest against physical and chemical elements. Coating can also be applied to modify the surface properties of the substrate. One of the most important aspects of coating processes is controlling the thickness of coating material over the substrate. As a subset of a family of chemical vapor deposition methods, iCVD relies on vapor-to-surface reactions to form solid ultrathin polymer films. Unlike other CVD methods, iCVD is unique in that a polymerization reaction is induced by a thermally or chemically activated initiator molecule, much like in liquid-based thermal polymerization except without the use of a liquid solvent medium. The aim of the study is to fabricate polymeric protective nano-coatings via iCVD on flat surfaces at low or ambient temperatures. A variety of polymers, including homopolymers of glycidyl methacrylate (GMA), cyclo hexyl methacrylate (CHMA) and 1H, 1H, 2H, 2H,-Perfluorodecyl acrylate (PFDA) and P(GMA-PFDA) copolymers were fabricated via iCVD. The surface roughness and contact angle values were measured. Smooth hydrophobic surfaces having high contact angle (approximately 130˚) were obtained with PPFDA and PGMA-co-PPFDA thin films. Chemical compositions of the homo and co-polymer films were also evaluated confirming the retention of functional groups during polymerization, thus opening possibility of using iCVD produced films in various sensor applications.
  • Master Thesis
    Modelling and Simulation of Zinc Based Batteries
    (Izmir Institute of Technology, 2016) Toptop, Evren; Ebil, Özgenç; Yüksel Özşen, Aslı; Ebil, Özgenç; Yüksel Özşen, Aslı; 03.02. Department of Chemical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of Technology
    Energy is the determining factor of productivity and quality of living. Electric energy is the most used energy form and lack of reserve for it hinders widespread use of renewable energy technologies. Advancements in renewable energy technologies, electric vehicles and consumer electronics are highly dependent on developments of new battery technologies. High energy density, long service life, using benign and abundant materials are few of the key requirements for next generation batteries. A model, a mathematical description of the system, is an effective tool to predict the behavior of batteries under specific conditions, thus reducing cost and time for the development. A mathematical model using finite element method was designed to simulate the discharge behavior of an experimental nickel-zinc battery that includes composite zinc and commercial nickel electrodes. The model employs thermodynamic and kinetic expressions for porous electrodes considering the concentration dependency of battery characteristics. The effects of initial zinc and nickel concentrations, anodic transfer coefficients of zinc and nickel electrode reactions on the electrochemical performance of the battery have been simulated. The discharge voltage, electrode porosities, and species concentrations in electrodes as a function of model parameters and time have been evaluated. It is observed that the model results are consistent with the experiment results considering that the battery operation is limited with zinc concentration. Initial zinc concentration is the major determining factor on discharge duration. Nickel oxyhydroxide concentration affects voltage magnitude. Transfer coefficients have only limited effects on discharge voltage and concentrations.
  • Master Thesis
    An Investigation of Electrochemical Stability of Zinc Electrodes for Battery Applications
    (Izmir Institute of Technology, 2014) Payer, Gizem; Çiftçioğlu, Muhsin; Ebil, Özgenç; Ebil, Özgenç; Çiftçioğlu, Muhsin; 03.02. Department of Chemical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of Technology
    Energy is the most important and inevitable requirement for humankind. The increasing energy demand has been connected with technological advances and the population growth. One of the most serious problems of the world is to provide sustainable energy. New alternative energy sources and renewable energy technologies have become notable research subjects due to wide availability of renewable energy sources in the world. However, most renewable energy sources do not provide uninterrupted energy to consumers. An economic, efficient and reliable energy storage technology is desperately needed. Therefore, academic research has focused on improving the capacity of electrochemical energy storage technologies. The main goal of this study is the preparation and characterization of zinc electrodes for battery applications using different zinc oxide powders with various morphologies and additives. Zinc oxide powders were synthesized with chemical precipitation method under different conditions (precursors, temperatures and aging times) in order to investigate their effects on ZnO morphology and on the performance of nickel-zinc battery. It was found out that the initial morphology of ZnO powder was not crucial for the electrochemical performance. Nickel-Zinc batteries with zinc electrodes prepared from commercial ZnO powder had discharge capacities around 247 mAhg-1 and showed slightly better performance compared to nickel-zinc batteries with zinc electrodes prepared from ZnO powders synthesized via chemical precipitation method. It was also determined that zinc electrode morphology was greatly affected by battery additives (PVA and PEG) and charging current density. The effects of some selected electrode additives (Ca(OH)2, PbO and PEG) on battery performance were also investigated. Zinc electrode with all additives showed improved electrochemical properties, such as higher discharge capacity (322 mAhg-1) and utilization ratio (48.86 %.)
  • Master Thesis
    Selective Loading of Organofilic Ag Nanoparticles in Ps-Pmma Blends
    (Izmir Institute of Technology, 2014) Tüzüner, Şeyda; Demir, Mustafa Muammer; Ebil, Özgenç; Demir, Mustafa Muammer; Ebil, Özgenç; 03.02. Department of Chemical Engineering; 03.09. Department of Materials Science and Engineering; 03. Faculty of Engineering; 01. Izmir Institute of Technology
    The association of nanoparticles with polymer blends offers significant features beyond the advantages of polymer composites prepared by single homopolymer. Since the blends undergo phase separation due to incompatibility of the constituent polymers into various internal structures, the particles can be segregated into one of the phases. Different location of the particles allows to develop novel microstructures; and thus, control over physical properties. In this study, Ag nanoparticles were prepared by reduction of AgNO3 via NaBH4. The particles were capped by cetyl ammonium bromide (CTAB) and were mixed with equimass blend of polystyrene (PS) and poly(methyl methacrylate) (PMMA) in tetrahydrofurane (THF). The solid content of blend solution was fixed at 2.5% w/v. The concentration of the particles with respect to polymer blend was at 0.7 wt %. The composite film was cast on glass slide. Surface feature of the composite films was examined by atomic force microscopy (AFM) and scanning electron microscopy (SEM). The surface of blend film without particles shows spherical pits with a size of 4.5 μm and rich in terms of PMMA. When particle size was small (diameter is around 20 nm), they preferentially located at the interface of the domains. The large particles with a diameter of 90 nm were found to locate in PMMA phase. Upon annealing of the composite film at 165 ˚C for 3 days, the particles move to the PS domains independent of the particle size and merely PS loaded composite is achieved.