Master Degree / Yüksek Lisans Tezleri
Permanent URI for this collectionhttps://hdl.handle.net/11147/3008
Browse
36 results
Search Results
Master Thesis The Effect of Metal Doping on Tio2 for Photocatalytic Applications(Izmir Institute of Technology, 2019) Alduran, Yeşim; Özyüzer, Lütfi; Öztürk, OrhanRecently, the photocatalysis method has been an active research area as a promising solution for environmental cleaning method, leading to self-cleaning and sterilization of solar cell surfaces to produce water dissociation reaction. Titanium dioxide (TiO2) is the most suitable semiconductor for photocatalytic applications due to its high oxidation potential and high efficiency when irradiated by ultraviolet light (UV). Undoped and Ruthenium (Ru+) doped TiO2 thin films were prepared using magnetron sputtering technique. All thin films were grown on SLG different ratios like 1 sec, 3 secs, 5 secs and 7 secs to set shutter position in magnetron sputter target. Transparent substrate SLG is coated with nearly 50 nm TiO2 thin films without compromising any optical properties. Samples were heat treated for two hours at 500°C to get the anatase phase crystal structure. The crystallization peaks of TiO2 are proved to get the anatase phase. Photocatalytic activity of TiO2 thin films are determined after 1, 3, 5 and 24 hours with organic pollution as a methylene blue dye degradation under UV light. The degradation of methylene blue was investigated kinetically and photocatalytic activity rate constants of the photocatalysts were calculated. All thin films could not reach super hydrophilicity state. Undoped TiO2 contact angle 47.309o and Ru doped TiO2 63.218o were evaluated. The photocatalytic degradation percentage of Methylene Blue was reached 87%, after 24 hours of UV irradiation, when using Ru-doped TiO2 thin film. Consequently, the anatase phase of Ru-doped TiO2 thin films are found best photocatalytic activity in self-cleaning performance.Master Thesis Optical Characterization of Nanoscale Dielectric Films on Curved Surfaces Using Near Field Diffraction Method(Izmir Institute of Technology, 2019) Ataç, Enes; Dinleyici, Mehmet SalihDemand on the high-quality optical thin films has increased because of the importance in the optical sensor technologies. The thicknesses of such films are usually shorter than the wavelength of visible light. Therefore, the optical characterization of these films is not a routine procedure especially on curved surfaces such as optical fiber. Besides, the methods in the literature and commercially available systems are either expensive, destructive or non-real time. In this thesis, it is aimed to propose a simple, inexpensive and non-destructive optical characterization method of nano-scale dielectric films on curved surfaces. The methodology of that approach can be described as the near field wavefront tracing diffraction by using structured light. In this way, it has been shown that sub-wavelength film thicknesses can be estimated. The proposed diffraction method is organized in four main stages. These are the coating of optical fibers, generation of structured light, determination of wave propagation via the near field Huygens-Fresnel wave-front tracing and sensing and processing of signal from the sensor array. Layer by layer assembly technique is used in coating process to keep under control the thickness of transparent film. Selection of various source types is about to changing of point spread function of applied field and observe the effects on intensity pattern. Using near field diffraction technique, sub-wavelength thickness of thin films can be predicted by taking the higher order components of diffraction pattern by recording at very close proximity to object. In this way, determination of thickness beyond the diffraction limits can be realized. Furthermore, the resolution of sensor array in sensing part is important since pixel size of the sensor array determines your detection limits to catch all variations on diffraction pattern. The whole process has a mathematical model with numerical analysis methods. This dissertation is about the proposing a mathematical estimation model for the optical properties of nano-scale dielectric films coated on curved surfaces. The experimental results show that near field Huygens-Fresnel wave-front tracing method by using structured light is a powerful technique.Master Thesis Growth and Characterization of Znsno Thin Films on Polymers for Oleds(Izmir Institute of Technology, 2019) Ekmekçioğlu, Merve; Aygün Özyüzer, GülnurThe use of flexible organic light-emitting diodes (OLEDs) in smartphones and televisions with inclined screen shows significant improvements in commercial applications. Recently, flexible OLEDs have been used in lightweight, portable, wearable and even deformable screens, sensors as well as solid-state lighting applications. Under favour of these applications, remarkable developments are observed in the production of flexible electronics. The advantages of OLEDs according to the existing liquid crystal display (LCD) technology are self-emission capability, wide viewing angle, fast response time, simple structure, and low driving voltage. Highly conductive and transparent anodes are required for efficiency and uniform light emission in OLEDs. Indium tin oxide (ITO) which is one of the most promising anodes among transparent conductive oxides (TCO), has superior electrical and optical properties such as ~85% high transmittance at the visible region and ~104 Ω−1 cm−1good conductivity. The reason is due to the bandgap range of about 3.70 eV. Zinc tin oxide (ZnSnO or ZTO) is another TCO commonly used for many applications in the literature. Alternative anodes eliminate the use of ITO due to the absence of indium element so that highly desirable. In this thesis, ZTO is used as anode instead of ITO thin film and the eligibility of ZTO as an anode in OLED production is explored. The advantages of the optimized ZTO thin film according to the ITO are that is abundant on earth, has better performance, has low surface resistance, has less surface roughness, is capable of being produced as an anode in OLEDs. In this thesis to be successful, at the first stage ZTO thin films have grown on soda lime glass by magnetron sputtering, then ZTO and ZTO/Ag/ZTO multilayer thin films respectively have been deposited on flexible Polyethylene terephthalate (PET) and Polyimide (PI) substrates by magnetron sputtering method. In this way, the best coated thin films have been investigated using spectrophotometry, energy-dispersive X-ray spectroscopy (EDS), scanning electron microscopy (SEM), Xray diffraction (XRD) and Raman spectroscopy.Master Thesis Improvement of Transparent Conductive Hybrid Ito/Ag Electrodes by Electro-Annealing(Izmir Institute of Technology, 2019) Uyanık, Zemzem; Aygün Özyüzer, GülnurHibrit ITO/Ag/ITO (IAI) ince film tabaka yapılarının optik ve elektriksel performansları, ITO ve Ag katmanı kalınlığının fonksiyonu olarak incelenmiştir. Hibrit IAI ince filmleri borosilikat cam üzerine oda sıcaklığında yüksek vakum altında dc mıknatıssal saçtırma yöntemi ile üretilmiştir. Hibrit yapıdaki ITO, Ag, ITO filmlerin kalınlığı düşük tabaka direncine ve yüksek optik geçirgenliğe sahip olacak şekilde ayarlanmıştır. ITO katmanları arasındaki gömülü metal Ag katmanı, 10 nm ile 25 nm arasında değişen kalınlıklarda kullanılmıştır. IAI tabakası analiz edildikten sonra IAI ince filmlerin kristalliğini iyileştirmek için elektro-tavlama uygulanmıştır ve elektrik akımının IAI ince filmler üzerindeki etkisinin araştırılmasıyla elektronik cihaz ömrünün arttırılması amaçlanmıştır. Elektro-tavlamanın endüstriyel uygulamalar için daha uygun bir teknik olduğu sonucuna varılmıştır. IAI ince filmin yüzey direnci elektro-tavlama işleminden sonra 8.7 Ω/□ olarak bulunmuştur en yüksek geçirgenliğe ise 88.9% da ulaşılmıştır. Hibrit IAI ince filmlerin optoelektronik özellikleri, ITO film kristalliğini etkileyen ara katman olan metal Ag kalınlığına bağlıdır. Hibrit IAI ince filmlerinin yapısal özellikleri, CuK����� radyasyonuna sahip (�����=0.154 nm) X-ışını kırınımı (XRD) (Philips X'Pert Pro) ile tavlama sıcaklığının fonksiyonu olarak karakterize edilmiştir. IAI ince filmlerinin morfolojisi hakkında bilgi taramalı elektron mikroskobu (SEM) ile elde edilmiştir. IAI ince filmin optik geçirgenliği 200-2600 nm dalga boyu aralığına sahip PerkinElmerLambda 950 UV/Vis/NIR Spektrofotometre ile ölçülmüştür. Yüzey direnci ölçümleri için Keithley 2424 kaynak metrisi kullanılarak dört nokta yöntemi uygulanmıştır.Master Thesis Efficiency Studies of Cu2znsns2 Thin Film Solar Cell(Izmir Institute of Technology, 2018) Meriç, Ece; Özyüzer, Lütfi; Aral, GürcanCu2ZnSnS4 (CZTS) is a promising candidate as an absorber layer for thin film solar cells due to not only its low cost but also nontoxic properties contrary to alternative materials such as CdTe and Cu(In,Ge)Se2 (CIGS). Recently, CZTS and similar chalcogenides have attracted remarkable attention because of their suitable properties. In my thesis; I studied the efficiency of Cu2ZnSnS4 thin film solar cells for various stoichiometric cases. Besides, the effect of back contact, buffer layer thickness and sulfurization time were investigated. CZTS thin films were fabricated by DC magnetron sputtering method on Molybdenum (Mo) coated Soda Lime Glass (SLG) and Ti foil substrates. Cu, Sn, Zn, Cu layers were, respectively, deposited on the substrates, and then sulfurization process was followed as the second step in the growth process to obtain a desirable CZTS formation. The as grown CZTS structure was investigated using Raman and X-Ray Diffraction (XRD) spectroscopies. Scanning electron microscopy (SEM) was used to investigate the surface morphology of the films. Energy dispersive spectroscopy (EDS) was used to define the chemical structure of the surface of the films. Next, a CdS buffer layer was deposited on CZTS absorber layer using CBD method at 85oC for varying times (60, 75 and 90 min). Then, ZnO and Al doped ZnO (AZO) layers were deposited on CdS. J-V curves were obtained for SLG/Mo/CZTS/CdS/ZnO/AZO solar cell structure. The photovoltaic characteristic of solar cells was studied and their dependence on CdS deposition time were found. Among all the device we produced, the highest efficiency was obtained for the device with the lowest CdS deposition time. In addition; effect of sulfurization time on the solar cell conversion efficiency was studied.Master Thesis Development of Nanofiltration Membranes Through Surface Modification of Polysulfone Based Ultrafiltration Membranes(Izmir Institute of Technology, 2017) Bar, Canbike; Alsoy Altınkaya, SacideStimuli responsive membranes have been used for suppressing fouling and regulating selectivity in different applications. These types of membranes are usually manufactured in thin film composite structure by either polymerizing stimuli-responsive monomer or coating stimuli-responsive polymer on a support. Responsiveness is due to their characteristic features which rely on reversible changes in mass transfer and interfacial properties as a result of changes in external environment such as pH, temperature and ionic strength. In this study, a pentablock copolymer (PBC) which consists of temperature responsive Pluronic F127 (PEO-b-PPO-b-PEO) in the middle block and pH responsive poly(N,N-(diethylamino)ethyl methacrylate) (PDEAEM) in the end blocks was used for designing a new type of thin film composite (TFC) nanofiltration membrane. The support of the composite membrane was prepared from a blend of polysulfone/sulfonated polyethersulfone using nonsolvent induced phase separation and the PBC was attached to the support via electrostatic interaction. The conformation of grafted PBC chains was determined by adsorption studies. The effects of PDEAEM block length, concentration of the copolymer and adsorption time on the adsorbed amount were investigated. Among three copolymer samples investigated (15, 20 and 25 kDa), the 25 kDa PBC displayed the highest responsiveness, thus, rejection properties were determined for the membranes prepared only from this sample. The influences of operation pH and temperature on the structure integrity of the membrane were investigated with pure water permeability measurements and the change in pore size was assessed by determining rejection of neutral solutes by the membranes. The membranes were further characterized with SEM, AFM, contact angle, XPS and zeta potential measurements. It was demonstrated that a new pH and temperature responsive, high flux TFC NF membrane was manufactured.Master Thesis Investigation of Sulfurization Temperature Effects on Cu2znsns4 Thin Flims Prepared by Magnetron Sputtering Method on Flexible Titanium Foil Substrates for Thin Flim Solar Cells(Izmir Institute of Technology, 2017) Buldu, Dilara Gökçen; Aygün Özyüzer, GülnurThis thesis presents the effect of sulfurization temperature on Cu2ZnSnS4 (CZTS) thin films on flexible titanium (Ti) foil substrates. The CZTS films was produced by using a two-stage method. In the first step, the metallic precursor layers Cu/Sn/Zn/Substrate were deposited on Ti foil substrate by using DC magnetron sputtering method. In the second step, the deposited metal precursors were sulfurized in a graphite box under Argon (Ar) ambient inside a tubular furnace under a definite temperature. To understand the effects of temperature on the formation of the CZTS structure several analyses were performed. Our samples, each with a different sulfurization temperature; ranging from 530 to 580 oC, were carried out and the structural properties of the absorber layer was determined. XRD measurements showed a sharp and intense peak coming from the (112) planes which was a strong evidence for good crystallinity. The intensity of (112) plane became a sharp and intense with increasing sulfurization temperature. Raman spectroscopy of the sulfurized thin films revealed that, the kesterite structure CZTS thin film were obtained with increasing sulfurization temperature. Electron Dispersive Spectroscopy (EDS) was also used for the compositional analysis of the thin films. EDS analysis showed that the films were grown with a Cu-poor Zn-rich composition. From these analyses we conclude that no interface formation occurred between the substrate and the CZTS thin films, hence, a buffer layer was not required. It was also seen that Ti foil was suitable as substrate for the growth of CZTS thin films with desired properties. We also conclude that the sulfurization temperature plays a crucial role for producing good quality CZTS thin films on Ti foil substrate.Master Thesis Temperature Dependence of Resistivity and Hall Coefficient in Cu2znsns4 Absorbers for Thin Film Solar Cells(Izmir Institute of Technology, 2017) Akça, Fatime Gülşah; Aygün Özyüzer, Gülnur; Özyüzer, Lütfienergy is the most powerful clean energy source to act on the current energy needing all over the world. The utilization of green energy systems should be promoted since these energy systems benefit consumers, industry and the environment effectively for the developing countries. This advancement can be solely achieved if renewable energy sources become more accessible. It means that not only cheaper but also handy clean energy systems are needed. In spite of relatively high efficiency obtained by using c-Si, Si solar modules require high budget for manufacturing. The high production cost of c-Si, PV industry is lead to search for cheaper candidate materials like Cu2ZnSnS4 (CZTS) as absorber layer in solar cells. The aim of the thesis is to investigate electrical properties of CZTS p-type intrinsic semiconductor compound on soda lime glass substrates, including the temperature dependent electrical conductivity, carrier concentrations and mobility extracted from Hall Effect measurements. Firstly, the metal precursor films were fabricated in multi-target sputtering system, then they were sulfurized inside the tubular furnace in order to obtain the CZTS compound. X-ray diffraction and Raman spectroscopy measurements revealed the formation of kesterite structure. A good crystallinity and grain compactness of the films were determined by scanning electron microscopy (SEM). Electrical properties were measured by van der Pauw techniques. Hall effect measurements showed the p-type semiconductor behavior for all samples at room temperature. Also, optical properties including absorption coefficient, spectral transmission, and optical band gap were determined to characterize CZTS thin films.Master Thesis Development of a Novel Active Packaging System Based on Layer-Sy Layer Deposition of Natural Antioxidants and Antimicrobials To Extend Food Products' Shelf Life(Izmir Institute of Technology, 2017) Akgün, Begüm; Korel, FigenIn recent years, Layer-by-Layer (LbL) assembly of thin films has been extensively investigated for many purposes, particularly for its functionality and simplicity of fabrication. Through LbL assembly; antioxidant agents have beenincorporated into active packaging systems in different forms, mainly including sachets, physical adsorption on packaging material surface, multilayer films which contact with food packaging surface. In previous studies, active packaging systen associated with LbL depositions were investigated, but no detailed investigation has been found about the application of controlled releasing-active packaging system on fresh-cut fruits. In this study, 20 bilayers of chitosan and alginate; respectively; were coated on amorphous polyethylene terephthalate (A-PET) sheets by dipping method. The LbL treated PET films were used for active packaging of fresh-cut peaches. Total soluble solids content and titrable acidity demonstrated that LbL active coating did not interfere with the natural postharvest behaviour. A lower weight loss was observed for LbL coated peach saples, suggesting that the presence of layer structure on PET strips could act as a barrier against fruit water loos. After 7 days of storage, the LbL treated samples have shown the best preservation of carotenoids, the lower PPO activity and higher phenolic index. Microbiological analysis has shown that all the microbiological analysis has that all the microorganism types which were invetigated were affected by the actice packaging system.Sensory results were really encouraging, as well. As a conclusion, LbL coating has been proved for being a useful technique to produce controlled-release active packaging systems on fresh-cut fruits.Master Thesis Self-Organized Network of Silicon Oxide on Epitaxial Graphene(Izmir Institute of Technology, 2017) Özkendir, Dilce; Çelebi, CemIn this thesis, I studied the formation and characterization of self-organized hexagonal-shaped SiO2 wrinkle structures on epitaxial graphene that was grown on SiC substrate. Monolayer graphene was grown by annealing the SiC substrate at high temperatures under ultra-high vacuum conditions. Following the growth process, SiO2 thin film was deposited on epitaxial graphene layer at different deposition temperatures by thermal evaporation method. We found that SiO2 film wrinkles on epitaxial graphene. The origin of the hexagonal shaped wrinkle structures were derived from the thermal expansion coefficient difference between epitaxial graphene and SiO2 thin film. The mesh density of these SiO2 hexagonal wrinkle structures was controlled by changing the cooling rate of the substrate after the thin film deposition. To make a comparison, SiO2 thin film was also deposited on CVD grown graphene and on bare SiC substrate. Unlike on the bare SiC surface, SiO2 thin film on epitaxial graphene exhibited a self-assembled network of hexagonally shaped wrinkles due to thermally induced compressive strain between the two materials. The observed network of wrinkles were found to be comprised of line shaped primary and secondary types of protrusions with distinct topographic characteristics as determined by optical microscopy, Scanning Electron Microscopy and Atomic Force Microscopy measurements. The wrinkle to wrinkle spacing and mesh density of the wrinkle network were modified simply by changing the SiO2 deposition temperature. Our experimental results imply that epitaxial graphene with its high chemical inertness on SiC offers a great potential to be used as a conventional substrate in the realm of thin film metrology.