Master Degree / Yüksek Lisans Tezleri

Permanent URI for this collectionhttps://hdl.handle.net/11147/3008

Browse

Filters

2002 - 200912010 - 20111

Settings

Department: search.filters.department.Thesis (Master)--İzmir Institute of Technology, Materials Science and EngineeringSubject: search.filters.subject.Silica

Search Results

Now showing 1 - 2 of 2
  • Master Thesis
    The Use and Characterization of Composite Alumina-Titania Membranes for Gas Separation
    (Izmir Institute of Technology, 2002) Topuz, Berna; Çiftçioğlu, Muhsin; Çiftçioğlu, Muhsin; 03.02. Department of Chemical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of Technology
    The preparation, characterization and pure gas permeation of sol-gel derived alumina and silica membranes were investigated in this work. The effects of various parameters on sol particle size and unsupported membranes pore structure were investigated by laser light scattering particle size and N2 adsorption-desorption analysis .-alumina membranes were prepared on ZrO2 supports by successive dipping into boehmite sols. Almost proportional decreases in sol particle size and membrane pore diameter were determined with increasing acid content during the boehmite sol preparation. Increasing the H+/Al3+ mole ratio from 0.1 to 0.25 caused the hydrodynamic particle size and BJH pore size to decrease from 65 to 30 nm and 3.6 to 2.9 nm, respectively. The pore size increased from 2.8 nm to 3 nm upon increasing the calcination temperature from 500 to 600oC. Unsupported membranes were heat treated in the 200 to 1200 oC range for the characterization of the phase structure. Boehmite was the dominant phase below 500 oC, gamma being the dominant phase up to 900 oC and pure .-Al2O3 phase was obtained upon heat treatment at 1200oC. Pinhole and crack free alumina membranes about 3 .m (double layer) in thickness were observed from SEM pictures with insignificant infiltration. The CO2 permeability through the double layer .-Al2O3 membrane calcined at 600 oC was about 2.25*10-7 mol/m2.s.Pa, and had a slight pressure dependence which may indicate Knudsen Diffusion and Laminar Flow as the effective transport mechanisms. Upon the calcination of a similar double layer alumina membrane at 500oC, the CO2 permeability decreased to 1.51*10-8 mol/m2.s.Pa and was independent of pressure. Silica membranes were prepared by a sol-gel technique. These sols were prepared by acid catalysed hydrolysis and condensation of tetraethylorthosilicate in the presence of a solvent. The effects of processing parameters like the acid type and amount utilized during sol preparation, sol aging, heat treatment conditions, dipping time on the membrane pore structure and the permeation of pure gases were investigated. The supported membranes were heat treated in the 50-400 oC range. The N2 and CO2 permeabilities of silica membranes varied in the 2.2 * 10-10 . 2.7 * 10-8 mol / m2.s.Pa and 1.2*10-9 . 6.95*10-8 mol / m2.s.Pa range for single layer membranes dipped for 10 seconds into the sol. The sols became viscous and gelled in 16 hours at 50 oC. The O2 permeability increased with aging time. The optimum dipping time during processing was determined to be 10 seconds. The permeabilities of these membranes increased significantly with the sol acid content. The thickness of the silica membranes were determined to be about 2.m and significant infiltration into the support was observed from the SEM pictures.
  • Master Thesis
    Development of Liquid Armor Materials and Rheological Behavior of Shear Thickening Fluids (stfs)
    (Izmir Institute of Technology, 2011) Erdoğan, Taner; Tanoğlu, Metin; Tanoğlu, Metin; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of Technology
    Colloidal dispersions have been extensively used in many industrial applications such as cosmetic, paint, cement, lubricant and ceramic. Shear thickening is non- Newtonian flow behavior often observed in concentrated colloidal dispersions as an increase in viscosity with increasing shear rate or applied stress. Shear thickening fluids (STFs) exhibit fluid and solid-like properties depending on the shear rate and thus can be used in a variety of applications. In the present study, STFs have been synthesized with various weight fractions of silica nanoparticles in polyethylene glycol (PEG)/ethyl alcohol by mechanical mixing method. The steady and dynamic rheological behavior of shear thickening fluids (STFs) was investigated with rheometer. STFs thermal properties were investigated through thermogravimetric analysis. STFs have been used to improve the performance of Kevlar woven fabrics for protective applications in ballistic and stab. STFs/Kevlar fabric composites have been prepared with different impregnation techniques to evaluate the effects of the STFs. The ballistic performance and stab resistance of STFs impregnated Kevlar fabrics were investigated. Rheological measurements revealed the shear thickening effect of silica nanoparticles/PEG systems depending on the shear rate. In dynamic experiments, the strain thickening behavior was found at critical combination of strain amplitude and frequency. The viscous G modulus values were found to be greater than the elastic G modulus. The elastic G and the viscous G modulus values were found to increase when the strain amplitude is kept constant and frequency is increased. The same strain thickening behavior was also found when the frequency was kept constant and the strain amplitude was increased. The puncture resistance of STFs/Kevlar fabric composites exhibited significant improvements as compared to the neat Kevlar targets. Based on the SEM results, STFs were uniformly impregnated over the entire surface on the Kevlar fabric and Kevlar fabrics completely coated with STFs. The ballistic test results revealed STF/Kevlar fabric composites have potential to obtain liquid armor materials.