Master Degree / Yüksek Lisans Tezleri

Permanent URI for this collectionhttps://hdl.handle.net/11147/3008

Browse

Filters

2018 - 201922020 - 20221

Settings

Publisher: search.filters.publisher.Izmir Institute of TechnologySubject: search.filters.subject.Strain rate

Search Results

Now showing 1 - 3 of 3
  • Master Thesis
    The Effect of Strain Rate on the Deformation Behavior of Additively Manufactured Short Carbon Fiber Reinforced Polyamide Composites
    (Izmir Institute of Technology, 2022) Güden, Mustafa; Zeybek, Mehmet Kaan; Güden, Mustafa; 01. Izmir Institute of Technology; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering
    The compression behavior of Polyamide 6 (PA6- nylon 6) and short carbon fiber reinforced polyamide 6 (Onyx) produced by the Fused Deposition Modelling (FDM) method was investigated at both quasi-static and dynamic strain rates. The effects of layer height, specimen shape and dimensions, build direction and the orientation of the layers on the compression behavior were also determined. The results showed that the addition of short carbon fibers to the PA6 matrix increased the compression strength by 3-4 times and the determined flow stress has a strong correlation with the porosity amount in the specimens. The compression test results showed that cylindrical specimens had slightly higher flow stress than the cubic specimens. The compression tests on the specimens produced with different lengths showed almost no difference regarding stress-strain behavior. Furthermore, the specimens produced with 90 degrees showed the highest elastic modulus and yield strength and the specimens produced with 30 and 60 degrees the lowest modulus and yield strength. The Concentric infill specimens exhibited higher elastic modulus values and flow stresses than Cross raster infill specimens at all strain rates. In the layers of concentric rings, the outer rings prevented the lateral expansion of inner rings, leading to higher flow stresses than the cross raster [0/90] lay-up. The flow stress of both PA6 and Onyx specimens increased with increasing strain rate. The rate sensitivities of PA6 and Onyx specimens were shown to be similar to each other.
  • Master Thesis
    Experimental and Numerical Analysis of the Strain Rate Dependent Compressive Strength of a Cellular Concrete
    (Izmir Institute of Technology, 2019) Akyol, Burak; Taşdemirci, Alper; Güden, Mustafa; Güden, Mustafa; Taşdemirci, Alper; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of Technology
    Experimental and numerical quasi-static and high strain rate tests, including compression, indentation and direct impact, were performed on a cellular concrete in order to investigate the effect of strain rate on the compressive strength. The results of compression tests indicated three distinct regions of the compressive strength dependence on strain rate. A relatively lower strain rate dependent compressive stress was found in the quasi-static strain rate-regime, 2x10-3-2x10-1 s-1, a relatively high strain rate dependent compressive stress in the dynamic strain rate-regime, 180-103 s-1 and a cut-off strength above 103 s-1. The dynamic increase factor (DIF=dynamic/static fracture strength) varied between 1 and 2.5 from quasi-static to dynamic strain rate-regime with a sharp increase after about 100 s-1. The indentation tests using 25 and 30 mm-diameter indenters in the quasi-static strain rate-regime (uniaxial state of strain) and resulted in moderate DIF values (1-1.13), very similar with those of the quasi-static compression tests (1-1.15). In the indentation tests, the DIF values significantly and also confirmed the numerically determined DIF values of concrete at 1000 s-1 (~1.30) without radial and axial inertia. The compression and direct impact tests in the Split Hopkinson Bar (SHPB) set-up were implemented numerically in LS-DYNA using an anisotropic strain rate insensitive material model, MAT_096 (MAT BRITTLE DAMAGE). The stress readings were performed at the specimen different locations of the SHPB and indicated that radial and axial inertia were dominant between 1 and 30 m s-1 (30-1000 s-1).
  • Master Thesis
    The Effect of Material Strain Rate Sensitivity on the Shock Deformation of an Aluminum Corrugated Core
    (Izmir Institute of Technology, 2018) Canbaz, İlker; Taşdemirci, Alper; Güden, Mustafa; Güden, Mustafa; Taşdemirci, Alper; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of Technology
    The effect of the material model on the crushing behavior of a layered 1050 H14 aluminum corrugated sandwich structure was investigated numerically as function of velocity (0.0048, 20, 60, 150 and 250 m s-1) using three different material models; elastic-perfectly plastic (model I), elastic-strain hardening (model II) and elastic-strain and strain rate hardening (model III). Three-dimensional finite element models were developed in the explicit finite element code of LS-DYNA. Between 0.0048 m s-1 and 20 m s-1, the numerically calculated stresses at the impact and distal end were almost the same and in equilibrium, showing a “quasi-static homogenous mode”. The deformation mode at 60 m s-1 was a “transition mode” and between 150 and 250 m s-1 a shock mode in which the layers were crushed sequentially. The numerical study showed that the strain and strain rate hardening models tended to induce non-sequential layer crushing. The collective layer crushing was also more pronounced in the material model II and III than the material model I. For low strain hardening aluminum alloys and similar materials, the effect of strain hardening in increasing plateau stress was more significant than the strain rate hardening at the quasi-static velocity, while both strain hardening and strain rate hardening effect increased with increasing velocity. The stress reduction by the inclusion of imperfections however declined with the velocity since the samples started to deform near the impact end as the velocity increased.