Master Degree / Yüksek Lisans Tezleri
Permanent URI for this collectionhttps://hdl.handle.net/11147/3008
Browse
18 results
Search Results
Now showing 1 - 10 of 18
Master Thesis Lithium Extraction From Geothermal Brine by Adsorption Method With Electrolytic Y-Mno2 Sorbent(Izmir Institute of Technology, 2022) Toprak, Seyra; Demir, Mustafa Muammer; Baba, AlperIn recent years, studies on the recovery of lithium metal have attracted great attention due to its wide application areas, especially in lithium-ion batteries. Recovery of lithium from brines is preferred considering the environmental impacts in mining. The application of manganese oxide sorbents to recover lithium from geothermal brines has been extensively studied as it is a potential source of lithium. In this thesis, adsorption was performed in Tuzla Geothermal Power Plant (TGPP) at 87 °C and 2 bar using a mini-pilot system in the reactor near the reinjection well of the plant to investigate the adsorption performance in field conditions. As a new approach, electrolytic manganese dioxide (γ-MnO2), which is widely used as cathode material in batteries, was used as the sorbent material for lithium and its adsorption/desorption performance was investigated. Batch adsorption experiments were performed in synthetic lithium solution and the optimum working conditions were determined as pH 12, adsorbent concentration of 3 g/L, and initial lithium-ion concentration of 200 mg/L. The highest adsorption capacity of the sorbent in the Langmuir model was found as 9.74 mg/g. The maximum adsorption performance was obtained at 1h adsorption in Tuzla GPP. In the continuation of the study, desorption was carried out in acidic medium with the brine-treated sorbent. Lithium concentration was enriched to around 250 ppm with repetitive desorption studies. Reusability of the sorbent was investigated and the reused sorbent showed almost 40% performance compared to virgin powder. γ-MnO2 was found as a promising sorbent for the separation of lithium from geothermal brines.Master Thesis Fabrication and Characterization of Ceramic Fibers From Preceramic Polymers(Izmir Institute of Technology, 2019) Özmen, Ecem; Ahmetoğlu, Çekdar Vakıf; Demir, Mustafa MuammerCeramic fibers which are classified as oxide and non-oxide fibers are preferred to use in applications which are carried out at high temperature since they have high strength, low thermal expansion, corrosion, and oxidation resistance. Non-oxide fibers are generally produced using preceramic polymers by the spinning method. The production of ceramic materials using preceramic polymers by spinning method is more advantageous than other methods since the production of complex materials could be achieved at lower temperatures. The preceramic polymer family is basically classified as polysiloxane, polysilazane and polycarbosilane. In this thesis, it was aimed to obtain ceramic fiber in the most economical way. In this context, a spinning device was designed and made. Additionally, polysiloxane which is the most economical preceramic polymer was used to produce ceramic fiber. Polysiloxanes were spun by melt spinning. Obtained fibers were cured by different methods. As a result of pyrolysis, 65-130 μm thickness SiOC fibers were achieved.Master Thesis Fabrication of Colloidal Photonic Crystals Via Langmuir Blodgett Technique and Their Integration of Polymer Matrix(Izmir Institute of Technology, 2019) İnci, Ezgi; Demir, Mustafa Muammer; Varlıklı, CananColloidal films have potential uses in various fields such as photonics, electronics, sensors, membrane filters, and surface devices owing to their unique optical properties. Photonic crystals composed of uniform diameter colloidal silica particles have been arranged in a periodic structure by taking inspiration from nature. The periodic structure of silica particles has physical interaction with light in a visible range. This special interaction is known as structural coloration. The close-packed monolayers and multilayers of colloidal silica particles in large area can be produced by using Langmuir Blodgett method. The integration of these photonic films with transparent polymer matrices having an elastomer feature provides for their use in optical sensor applications. In this thesis, we examined the fabrication of mechano-sensitive nanostructured films based on colloidal particles. Silica colloidal particles were synthesized at different sizes by using Stöber Process. Langmuir-Blodgett deposition was used to create three-layer of photonic crystal films with different particle diameters. For this purpose, various substrates were examined for the Langmuir Blodgett deposition process before starting the coating. The coated silica particles on the glass substrate were then embedded in an elastomeric transparent matrix. The generation of structural coloration after stretching was examined in manufactured elastomer films. In accordance with this purpose, various polymers such as acrylates and siloxanes with elastomer properties have been used. The structural characterization of these composite films and their optical properties were summarized in this thesis.Master Thesis A Novel Approach for Fabrication of Free-Standing Conductive Network: Pedot: Pss Based Bendable Chemo and Photoresistor(Izmir Institute of Technology, 2019) Mutlu, Mustafa Umut; Yıldız, Ümit Hakan; Demir, Mustafa MuammerElectrospinning is a simple and versatile technique for the fabrication of polymeric nanofibrous substrate with high surface to volume ratio. Besides high surface to volume ratio, their dimensional stability and flexibility make it a perfect candidate for conductive network for various sensor applications. Free-Standing conductive network can be fabricated by deposition of PEDOT:PSS or MWCNT through bendable nanofibrous substrate. As a simple example for sensor applications, the moving object has been sensed through the electrostatic interactions between fibers and object. The sensing range has been found to be 1-5 cm above the surface of fabric. By the controlled combination of conductive polymers and electrospun polymer nanofibers effective device miniaturization has been provided without loss of performance. The noncontact motion sensor platform has unique flexibility and light weight holding a potential for wearable sensor technology. For another application as a wearable electronics, the controlled combination of conductive network and light-matter interaction provides opportunities to fabricate photo-resistor exhibits broad band response 400 to 1600 nm that holding promises for ultra-thin sensors used in telecommunication. As a final example, we report the effect of gold and iron oxide nanoparticles on the selectivity and sensitivity of MWCNT or PEDOT:PSS based chemiresistor responsive to VOCs. The interplay between conductive layer by gold and iron oxide nanoparticles resulted a significant conductivity improvement that affecting selectivity which is governed by the interaction between electron-donating VOCs and NP doped conductive layer due to variation in charge carrier densities in conductive layer lattice.Master Thesis Synthesis of Artificial Metal (fe,mg) Silicate Deposits Under High Pressure and Temperature Conditions and Development of Polymeric Inhibitor for Metal Silicate Scaling(Izmir Institute of Technology, 2017) Çelik, Aslı; Demir, Mustafa MuammerTurkey has to import energy from other countries, because of having not enough sources. Geothermal energy is one of the renewable energy that can be readily founded in Turkey. At the core of the Earth by definition, the high temperature and pressure cause some rock to melt, creating magma convection upward since it is lighter than the solid rock. The magma heats rock and water in the crust. Tuzla geothermal field is the study area and there are NaCl, Mg ,Fe,Si , Ca and Zn metals and CO2 (g) in brine. While geothermal fluids are pumped from down to top the temperature and pressure decreased and CO2 is released. So,the pH level increases and causes silicate, sulfonate and calcide scaling problems. Moreover, silica is reacted with metal oxides to more stable scales. The production of electricity decreases and while cleaning and the system is shot-down. The present method of strong acid cleaning, harms components as well as create potential risk for the health of employees. In this project, artificial metal-silicate deposit was synthesized with close composition and morphology to natural scale, and potential inhibitors were synthesized and tested. Firstly, synthesizing of artificial deposit is necessary in the laboratory setting. For this purpose, we can simulate the course of temperature and pressure values will be used in autoclave reactor system. Secondly, the functional groups that exhibit inhibitory feature(s) have the potential of macromolecules (Poly (vinyl sulfonic acid), Poly (vinyl phophonic acid), Polyacrylamide and their copolymers and tercopolymer) were tested.Master Thesis Field Emission Electron Source Based on Silicon Carbide Nanopillars(Izmir Institute of Technology, 2017) Yeşilpınar, Damla; Çelebi, Cem; Demir, Mustafa MuammerIn this thesis work, I studied the fabrication and the field emission characteristics of SiC nanopillar based electron field emitters. The first objective of this thesis was to fabricate a large area nanopillar array on bulk 6H-SiC substrate. Accordingly, a nanosphere assisted technique was developed to create a conventional Cr/Ni hard mask to acquire desired etch mask pattern on the C-terminated face of 6H-SiC. The nanopillars were then fabricated by ICP-RIE. Two sets of nanopillars with different aspect ratios and geometries were fabricated for two different ICP-RIE durations. 1 min long etch resulted in nanopillar arrays with blunt tip apex and an aspect ratio of 3.4, where 2 min long etch produced nanopillar arrays with an aspect ratio of 4.9 and a sharp tip apex with an estimated radius of curvature of about 18 nm. As the second objective; the electron field emission characteristics of the produced nanopillars with two different aspect ratios and geometries were investigated and the obtained results were compared with each other. We found that the nanopillars with sharp tip apex produced field emission currents up to 240 μA/cm2 under 17.4 V/μm applied electric field, as the nanopillars with blunt tip apex produced an emission current of 70 μA/cm2. The threshold electric fields were found to be 9.1 V/μm and 7.2 V/μm for the nanopillars with blunt and sharp tip apex, respectively. Time dependent stability measurements yielded stable electron emission without any abrupt change in the respective current levels of both samples.Master Thesis Glucose Biosensor Applicatiın of Electrospun Polyvinyl Alacohol (pva) Fibers(Izmir Institute of Technology, 2016) Berber, Emine; Demir, Mustafa Muammer; Yıldız, Ümit HakanElectrospinning is a simple and versatile technique for the fabrication of polymeric nanofibrous membranes with high surface to volume ratio. Besides the large surface area of the fibrous membranes, their dimensional stability and flexibility allows the immobilization of biomolecules on to the nanofiber surfaces. Therefore, electrospun nanofibers have been extensively used in enzyme electrodes. This thesis examines the glucose biosensor application of electrospun polyvinyl alcohol (PVA) nanofibers – carbon nanotube (CNT) nanocomposite membranes. By manipulating the structural design and the composition of the nanocomposite membranes, glucose sensing efficiency of the five different enzyme electrodes a) Glucose oxidase (GOx) immobilized PVA electrospun electrode, b) Glucose oxidase (GOx) immobilized PVA electrospun electrode containing multi-walled carbon nanotube (MWCNT), c) Glucose oxidase (GOx) immobilized PVA electrospun electrode containing Poly(diallyldimethylammonium chloride) (PDDA) functionalized multi-walled carbon nanotube (MWCNT) d) Glucose oxidase (GOx) immobilized PVA electrospun electrode containing Poly(diallyldimethylammonium chloride) (PDDA) functionalized single-walled carbon nanotube (SWCNT), e) Interfacially cross-linked PVA electrospun electrode containing Poly(diallyldimethylammonium chloride) (PDDA) functionalized multi-walled carbon nanotube (MWCNT) were comperatively studied. PVA electrospun nanofibers were fabricated by using electrospinning technique. Morphology and average diameter of the fibers were characterized by using Scanning Electron Microscopy (SEM). Average diameter for the neat PVA electrospun fibers were 115 nm. Carbon nanotubes were oxidatively functionalized by acid treatment and addition of functional groups after acid treatment was proved by using Raman Spectroscopy. Glucose sensing activities of the electrodes were amperometrically measured at an applied voltage -0.5 V (vs. Ag/AgCl) in 0.1M phosphate buffer solution (PBS pH 7). Glucose detection sensitivies of the electrodes were calculated as 19.6, 27.7, 67.5, 44.4, 4.0 μA mM-1cm-2 respectively.Master Thesis Characterization and Expansion Behaviour of Perlite(Izmir Institute of Technology, 2016) Gül, Dilek; Şentürk, Ufuk; Demir, Mustafa MuammerPerlite is a silica-based organic glass. When it is instantaneously heated, it shows expansion by releasing a certain amount of water. Approximately 70% of perlite reserves in the world are found in Turkey. The porous structure of expanded perlite leads to use this material in many industrial areas; therefore, this is highly advantageous from the economic standpoint. In this study, the expansion behaviours of perlite samples, which were taken from İzmir (Bergama Mine), Kütahya (Avdan Mine), and Erzincan (Mollatepe Mine) were both characterized and investigated in the laboratory. The instrumentation techniques, X-ray Diffraction (XRD), X-ray Fluorescence (XRF), Scanning Electron Microscopy (SEM), Thermogravimetric Analysis (TGA), and Optic Microscope were used to characterize the perlite. The determination of the amorphous and crystal structure of perlite, the chemical composition of perlite, the measurement of loss of mass, the morphological characterization of perlite, and the form of raw and expanded perlite samples were obtained by XRD, XRF, TGA, SEM and Optic Microscopy, respectively. Four different heat treatments as 600 ˚C, 800 ˚C , 900 ˚C and 1000 ˚C and four different sizes 400-500 μm, 315-400 μm, 200-315 μm and 160-200 μm were conducted in the laboratory and the their bulk volumes and densities were compared before and after heat treatment. The perlite sample from Bergama 01 showed the largest expansion in all samples. As results of the analyses, the amount of crystal and water release in the perlite which had an influence on expansion process were consistent with the literature. The analyses were conducted until 1000 ˚C due to forming sinter above softening temperature. Additionally, the expanded perlite samples in the industrial furnace were compared with the expanded perlite samples in the laboratory more porous structure was observed. As a conclusion, the perlite samples from the different regions of Turkey were characterized and analyzed in terms of expansion behaviour in this study.Master Thesis Integration of Red & Blue Tl Materials To Different Polymer End-Use(Izmir Institute of Technology, 2016) İncel, Anıl; Demir, Mustafa MuammerTriboluminescence (TL) is known as the emission of light upon the application of any mechanical force. In this master thesis, two organometallic-based TL crystals, which are EuD4TEA and Cu(NCS)(py)2(PPh3) were obtained and they were integrated in the transparent polymers: poly (methylmetacrylate) (PMMA), poly (styrene) (PS), poly (urethane) (PU) and polyvinylidene fluoride (PVDF) for different end-use. In the development of composites, two different processes were carried out: i) embedding (or blending) and ii) surface impregnation. The different end-use polymers were used as transparent polymer film, electrospun nanofibers, and nanobeads. TL performance of composites were investigated by using drop tower system which was specficically designed for this research. Atomic force microscopy (AFM), scanning electron microscopy (SEM) were used to characterize the topographic and morphologic properties of both polymers and composites. Additionally, fluorescence microscopy helped to understand the signal of emitted light by composites. Lastly, piezoelectric properties of composite materials were invetigated by oscilloscope. According to results, type of process, particle size of crystal, surface property and form of host material (polymer), the concentration of crystalline particles in composites were determined as the main parameters and the results were estimated with respect to these parameters. PU-based composite film and fiber show better stability towards mechnical stress rather than PMMA, PS, and PVDF due to the roughness surface of thin-film surface for film-based composites, smallest wickerwork formation of electrospun mats for fiber-based composite, and the chemical affinity of PU with TL crystals.Master Thesis Electrochemical Properties of Titania Based Powders(Izmir Institute of Technology, 2015) Türkay, Cem; Demir, Mustafa Muammer; Çiftçioğlu, MuhsinGlobal warming arising from the greenhouse effect is globally accepted as the main problem which may threaten the life on the earth. Excess emission of carbon dioxide which leads to the more absorption of solar radiation in the atmosphere is the main reason for global warming. Carbon dioxide present in the atmosphere is balanced by natural photosynthesis; however this balance was disturbed by the increasing amount of carbon dioxide emissions after industrial revolution. Intense efforts was made by many scientists to find solutions to decrease the carbon dioxide level in the atmosphere and the pioneering studies were conducted in the early 1970s which founded the basic theory of artificial photosynthesis. The conceptual idea on conducting photosynthesis by technologically feasible processes was accepted by many scientists and the research on artificial photosynthesis accelerated in the last 10 years. The enhancement of the efficieny of artificial photosynthesis, by which alternative fuels such as methane, methanol may be produced, can be realized by doping titanium dioxide which is the most widely used photocatalyst in the literature. The determination of new electrochemical properties obtained by doping titanium dioxide is crucial since the oxidation/reduction reactions are controlled by the electrochemical structure of this material. Bandgap and band position energy levels which are important properties in photocatalysis can be determined and the efficiency of photoreduction under UV or visible light corresponding to these energy levels can be improved. Cyclic voltammetry (CV) can be used to determine the electrochemical properties of titanium dioxide and these properties can be improved by using the information obtained with this method. The effects of rare earth element doping on the electrochemical properties of titanium dioxide were investigated through out this Msc study. It was found that doping of titanium dioxide is significantly increased the electrochemical activity with rare earth elements. The increase in the doping amount of elements showed that articial photosynthesis activity of titanium dioxide may be enhanced by rare earth element doping.