Master Degree / Yüksek Lisans Tezleri

Permanent URI for this collectionhttps://hdl.handle.net/11147/3008

Browse

Filters

2005 - 200912010 - 20121

Settings

Author: search.filters.author.Eroğlu, Ahmet EminSubject: search.filters.subject.Arsenic

Search Results

Now showing 1 - 2 of 2
  • Master Thesis
    Use of Ion Exchange Resins Modified With Zero-Valent Iron for the Sorption/Speciation of Inorganic As(iii) and As(v) in Waters
    (Izmir Institute of Technology, 2012) Bölek, Deniz; Eroğlu, Ahmet Emin
    Arsenic is a cumulative toxic element and according to Environmental Protection Agency its maximum admissible concentration is established as 10.0 μgL-1 in drinking water. The consumption of arsenic via drinking contaminated water causes chronic and acute poisoning which result in different cancer types. Therefore, determination, speciation and removal of arsenic compounds from waters are important. This study aims to develop a novel sorbent for removal of inorganic arsenic species from contaminated waters. For this purpose a strong anion exchange resin (Amberlite IRA 458) was modified with zero valent iron (ZVI). In the first part of the study, various commercial anion exchange resins and novel resins prepared in the study were used for sorption and speciation of inorganic arsenic. For all the sorbents, the optimized sorption parameters were determined to be 25 ˚C for sorption temperature, 50.0 mg for sorbent amount, 60 min for shaking time for 20.0 mL of 100.0 μgL-1 of arsenic species. The release of As(III) and As(V) from the sorbents was realized using two eluents, 2% (m/v) NaOH + 3% (m/v) NaCl and 5% (m/v) NaOH + 3% (m/v) NaCl, respectively. The accuracy of the proposed methodology was verified with sorption studies for various water types spiked with 100.0 μgL-1 As(III) and As(V). Sorption values of ZVI-IRA 458 were determined to range between 59.1% and 100% for As(III) and between 61.5% and 100% for As(V). Moreover, the sorption efficiencies of the novel sorbents were compared with those of the commercial sorbents.In the final part of the study, the sorption results demonstrated that the most effective immobilization method was NaBH4 reduction and the most efficient resin to be modified was Amberlite IRA 458. Also, the sorption characteristic of ZVI-modified resins showed that the removal efficiency depended on the type of resins and arsenic species in water.
  • Master Thesis
    Separation of Trace Antimony and Arsenic Prior To Hydride Generation Atomic Absortion Spectrometric Determination
    (Izmir Institute of Technology, 2005) Yersel, Müşerref; Eroğlu, Ahmet Emin
    A separation method utilizing a synthetic zeolite (mordenite) was developed in order to eliminate the gas phase interference of Sb(III) on As(III) during quartz furnace hydride generation atomic absorption spectrometric (HGAAS) determination. The efficiency of the proposed separation method in the reduction of suppression effects of several metal ions on As(III) signal was also investigated. Among the volatile hydride forming elements and their different oxidation states tested (Sb(III), Sb(V), Se(IV), Se(VI), Te(IV), and Te(VI)), only Sb(III) was found to have a signal depression effect even at low (µg l-1) concentrations under the experimental conditions employed. It has been shown that mordenite adsorbs Sb(III) quantitatively, even at a concentration of 1000 µg l-1, at pHs greater than 2, and also, it reduces the initial concentrations of the metal ions to lower levels which can be tolerated in many studies. The adsorption of Sb(III) on mordenite follows the Freundlich isotherm and is endothermic in nature.