Civil Engineering / İnşaat Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/13
Browse
17 results
Search Results
Article Poliamid 6/6 (pa 66) Mikrofiberler ile Toklaştırılmış Tabakalı Kompozitlerin Mod-ı Delaminasyon Direncinin İstatiksel Analizi(Niğde Ömer Halisdemir Üniversitesi, 2019) Beylergil, Bertan; Tanoğlu, Metin; Aktaş, EnginFiber takviyeli kompozitler, ağırlıklarına oranla yüksek mukavemet ve rijitlikleri nedeniyle uzay ve otomotiv yapısal parçalarında yaygın olarak kullanılmaktadır. Delaminasyon, bu kompozitlerde görülen en yaygın ve kritik hasar modudur. Bu kompozitlerin delaminasyon direncini arttırmak amacıyla, nanokatkılar ile epoksi toklaştırması, dikişleme, z-pimler ve arayüzeyde mikro/nanofiber kullanılması gibi pek çok sayıda teknik geliştirilmiştir. Bu çalışmada, poliamid 6/6 (PA 66) mikrofiberler ile toklaştırılmış karbon fiber/epoksi kompozitlerin Mode-I delaminasyon direnci Weibull dağılımı kullanılarak istatiksel olarak analiz edilmiştir. Test verilerinin istatiksel olarak değerlendirilmesi sonucunda PA 66 mikrofiberlerin kullanılmasının %90 güven seviyesinde kırılma tokluğunu yaklaşık %445 mertebesinde arttırdığı gözlemlenmiştir.Article Citation - WoS: 8Citation - Scopus: 9Dynamic Behavior Predictions of Fiber-Metal Laminate/Aluminum Foam Sandwiches Under Various Explosive Weights(SAGE Publications, 2016) Baştürk, Suat Bahar; Tanoğlu, Metin; Çankaya, Mehmet Alper; Eğilmez, Oğuz ÖzgürApplication of blast tests causes some problems to characterize the performance of panels due to the drastic conditions of explosive medium. Real test has high safety concerns and is not easily accessible because of its extra budget. Some approaches are needed for the preliminary predictions of dynamic characteristics of panels under blast loading conditions. In this study, the response of sandwiches under blast effect was evaluated by combining quasi-static experiments and computational blast test data. The primary aim is to relate the quasi-static panel analysis to dynamic blast load. Based on this idea, lightweight sandwich composites were subjected to quasi-static compression loading with a special test apparatus and the samples were assumed as single degree-of-freedom mass-spring systems to include dynamic effect. This approach provides a simpler way to simulate the blast loading over the surface of the panels and reveals the possible failure mechanisms without applying any explosives. Therefore the design of the panels can be revised by considering quasi-static test results. In this work, the peak deflections and survivabilities of sandwiches for various explosive weights were predicted based on the formulations reported in the literature. Major failure types were also identified and evaluated with respect to their thicknesses.Article Citation - WoS: 16Citation - Scopus: 24Developing Polymer Composite-Based Leaf Spring Systems for Automotive Industry(Walter de Gruyter GmbH, 2018) Öztoprak, Nahit; Güneş, Mehmet Deniz; Tanoğlu, Metin; Aktaş, Engin; Eğilmez, Oğuz Özgür; Şenocak, Çiler; Kulaç, GedizComposite-based mono-leaf spring systems were designed and manufactured to replace existing mono-leaf metal leaf spring in a light commercial vehicle. In this study, experimentally obtained mechanical properties of different fiber-reinforced polymer materials are presented first, followed by the description of the finite element analytical model created in Abaqus 6.12-1 (Dassault Systemes Simulia Corp., RI, US) using the obtained properties. The results from the finite element analysis are presented next and compared with actual size experimental tests conducted on manufactured prototypes. The results demonstrated that the reinforcement type and orientation dramatically influenced the spring rate. The prototypes showed significant weight reduction of about 80% with improved mechanical properties. The hybrid composite systems can be utilized for composite-based leaf springs with considerable mechanical performance.Article Citation - WoS: 39Citation - Scopus: 40Mode-I Fracture Toughness of Carbon Fiber/Epoxy Composites Interleaved by Aramid Nonwoven Veils(Techno Press, 2019) Beylergil, Bertan; Tanoğlu, Metin; Aktaş, EnginIn this study, carbon fiber/epoxy (CF/EP) composites were interleaved with aramid nonwoven veils with an areal weight density of 8.5 g/m(2) to improve their Mode-I fracture toughness. The control and aramid interleaved CF/EP composite laminates were manufactured by VARTM in a [0]4 configuration. Tensile, three-point bending, compression, interlaminar shear, Charpy impact and Mode-I (DCB) fracture toughness values were determined to evaluate the effects of aramid nonwoven fabrics on the mechanical performance of the CF/EP composites. Thermomechanical behavior of the specimens was investigated by Dynamic Mechanical Analysis (DMA). The results showed that the propagation Mode-I fracture toughness values of CF/EP composites can be significantly improved (by about 72%) using aramid nonwoven fabrics. It was found that the main extrinsic toughening mechanism is aramid microfiber bridging acting behind the crack-tip. The incorporation of these nonwovens also increased interlaminar shear and Charpy impact strength by 10 and 16.5%, respectively. Moreover, it was revealed that the damping ability of the composites increased with the incorporation of aramid nonwoven fabrics in the interlaminar region of composites. On the other hand, they caused a reduction in in-plane mechanical properties due to the reduced carbon fiber volume fraction, increased thickness and void formation in the composites.Conference Object Citation - Scopus: 1Development of Composite Drive Shaft Tube for Automotive Industry(Applied Mechanics Laboratory, 2019) Arslan Özgen, Gizem; Tanoğlu, Metin; Aktaş, Engin; Yücetürk, KutayWeight, vibration, fatigue, and critical speed limitations have been recognized as serious problems in drive shafts in automotive industry for many years. Conventional drive shaft is made up into two parts to increase its fundamental natural bending frequency. This present work deals with the replacement of conventional steel drive shaft with a composite counterparts. The benefits of eliminating the two piece shafts are significant reductions in weight, noise, vibration and harshness. In this work, one-piece propeller shaft composed of carbon/epoxy and glass/epoxy composites have been designed and manufactured for a rear wheel drive automobile. The performance measures are static torque transmission capability, torsional buckling and the fundamental natural bending frequency. The tubular composite shaft samples are being manufactured by using filament winding technique. To predict the torsional properties, fatigue life and failure modes of composite tubes for different fiber orientation angle and stacking sequence, finite element analysis (FEA) has been used. The predicted and experimental values has been reported for comparison. The next phase of work consists of optimization of shaft for the objective function as weight and fundamental natural frequency considering different stacking sequence and fiber orientation. © CCM 2020 - 18th European Conference on Composite Materials. All rights reserved.Article Citation - WoS: 97Citation - Scopus: 110Effect of Polyamide-6,6 (pa 66) Nonwoven Veils on the Mechanical Performance of Carbon Fiber/Epoxy Composites(Elsevier Ltd., 2018) Beylergil, Bertan; Tanoğlu, Metin; Aktaş, EnginIn this study, carbon fiber/epoxy (CF/EP) composites were interleaved with polyamide-6,6 (PA 66) nonwoven veils at two different areal weight densities (17 and 50 gsm) to improve their delamination resistance against Mode-I loading. Mode-I fracture toughness (DCB), tensile, open hole tensile (OHT), flexural, compression, short beam shear (ILSS) and Charpy-impact tests were performed on the reference and PA 66 interleaved composite specimens. The DCB test results showed that the initiation and propagation Mode-I fracture toughness values of the composites were significantly improved by 84 and 171% using PA 66-17 gsm veils respectively, as compared to reference laminates. The use of denser PA 66-50 gsm veils in the interlaminar region led to higher improvement in fracture toughness values (349% for initiation and 718% for propagation) due to the higher amount of veil fibers involved in fiber bridging toughening mechanism. The incorporation of PA 66-50 gsm nonwoven veils also increased the ILSS and Charpy impact strength of the composites by 25 and 15%, respectively. On the other hand, the PA 66 veils reduced in-plane mechanical properties of CF/EP composites due to lower carbon fiber volume fraction and increased thickness.Book Part Scissor Linkages in the Design of Adaptive Morphologies(Walter de Gruyter GmbH, 2019) Akgün, Yenal; Maden, Feray; Gür, Şebnem; Kiper, Gökhan; Korkmaz, Koray; Aktaş, Engin; Yar Uncu, MüjdeScissor linkages are capable of forming various expandable structures. Architects can benefit from this type of linkage especially for designing adaptive, movable, transformable shell structures and deployable beam-like structures. Product designers may benefit as well. The two different methods described here convey the basic design approaches. The unit-based method is very effective for obtaining primary geometries like a dome, arch, circle or line, using serial multiplications and arrays of one of the scissor unit types presented here. The loop assembly method is more convenient when a final form, be it straight or free-form, is the main point of departure. In this case, unlike in the unit-based method, it is not necessary to opt for a specific scissor unit type and its dimensional constraints from the beginning. Designers can choose a type and number of loops and then define the scissor units following the loop sides. Since deployability is guaranteed by applying this method, the architect is free to choose the loop type most suitable for the functional needs and aesthetic concerns of the specific design. With the loop assembly method all loop alternatives can be assembled to scissor structures, their possible motions can be tested and evaluated in a short time, whereas the unit-based method is limited to a single type of motion that a specific unit can provide.Article Citation - WoS: 31Citation - Scopus: 33Modification of Carbon Fibre/Epoxy Composites by Polyvinyl Alcohol (pva) Based Electrospun Nanofibres(Adcotec Ltd., 2016) Beylergil, Bertan; Tanoğlu, Metin; Aktaş, EnginIn this study, the effects of modifying interlaminar region of unidirectional carbon fibre/epoxy composites by the incorporation of electrospun polyvinyl alcohol (PVA) nanofibres were investigated. PVA nanofibres were directly deposited onto the carbon fabrics by electrospinning method to improve mechanical performance of those composites. The features of the electrospun nanofibres were characterized by microscopy techniques. The unidirectional carbon fibre/epoxy composite laminates with/without PVA nanofibre interlayers were manufactured by vacuum-infusion technique in a [0]4 configuration. Tensile, three-point bending, compression, Charpy-impact and Mode-I fracture toughness tests (Double Cantilever Beam (DCB)) were carried out in accordance with ASTM standards to evaluate mechanical performance of the composites. Scanning electron microscopy (SEM) observations were made on the specimens to evaluate microstructural features. It was observed that the carbon fabrics were successfully coated with a thin layer of PVA nanofibres by electrospinning technique. The results showed that P VA nanofibres improve the mechanical properties of unidirectional carbon/epoxy composite laminates when subjected to in-plane loading. On the other hand, PVA nanofibres slightly reduced the mode-I fracture toughness values although they led to more stable crack propagation.Article Citation - WoS: 108Citation - Scopus: 117Enhancement of Interlaminar Fracture Toughness of Carbon Fiber–epoxy Composites Using Polyamide-6,6 Electrospun Nanofibers(John Wiley and Sons Inc., 2017) Beylergil, Bertan; Tanoğlu, Metin; Aktaş, EnginIn this study, carbon fiber–epoxy composites are interleaved with electrospun polyamide-6,6 (PA 66) nanofibers to improve their Mode-I fracture toughness. These nanofibers are directly deposited onto carbon fabrics before composite manufacturing via vacuum infusion. Three-point bending, tensile, compression, interlaminar shear strength, Charpy impact, and double cantilever beam tests are performed on the reference and PA 66 interleaved specimens to evaluate the effects of PA 66 nanofibers on the mechanical properties of composites. To investigate the effect of nanofiber areal weight density (AWD), nanointerlayers with various AWD are prepared by changing the electrospinning duration. It is found that the electrospun PA 66 nanofibers are very effective in improving Mode-I toughness and impact resistance, compressive strength, flexural modulus, and strength of the composites. However, these nanofibers cause a decrease in the tensile strength of the composites. The glass-transition temperature of the composites is not affected by the addition of PA 66 nanofibers. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 45244.Article Citation - WoS: 2Citation - Scopus: 2Trait-based heterogeneous populations plus (TbHP+) genetic algorithm(Elsevier Ltd., 2009) Tayfur, Gökmen; Sevil, Hakkı Erhan; Gezgin, Erkin; Özdemir, SerhanThis study developed a variant of genetic algorithm (GA) model called the trait-based heterogeneous populations plus (TbHP+). The developed TbHP+ model employs a memory concept in the form of immunity and instinct to provide the populations with a more efficient guidance. Also, it has an ability to vary the number of individuals during the search process, thus allowing an automatic determination of the size of the population based on the individual qualities such as character fitness and credit for immunity. The algorithm was tested against the classical GA model in convergence and minimum error performance. For this purpose, 5 different mathematical functions from the literature were employed. The selected functions have different topological characteristics, ranging from simple convex curves with 2 variables to complex trigonometric ones having several hilly shapes with more than 2 variables. The developed model and the classical GA model were applied to finding the global minima of the functions. The comparison of the results revealed that the developed TbHP+ model outperformed the classical GA in faster convergence and minimum errors, which may be explained by the adaptive nature of the new paradigm.