Civil Engineering / İnşaat Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/13
Browse
7 results
Search Results
Now showing 1 - 7 of 7
Article Citation - Scopus: 2Application of Endurance Time Method in Seismic Assessment of Rc Frames Designed by Direct Displacement-Based Procedure(Turkish Chamber of Civil Engineers, 2024) Karımzada, Nisar Ahmad; Shırkhanı, Amir; Aktaş, EnginThis paper addresses the Direct Displacement-Based Design (DDBD) approach of multi-story RC frame structures consistent with changes to design criteria between Turkish earthquake codes of TSC-2007 and TBEC-2018. The corresponding response modification factor (R) of structures designed based on the DDBD approach is also estimated in this research. The design base shear forces of both codes are compared considering different R factors and also with that of the DDBD approach. The results showed that the DDBD approach, as per TBEC-2018, provides RC frame structures with higher R values compared to the similar approach in accordance with TSC-2007. The Endurance Time (ET) method is a time history-based procedure for seismic assessment of structures under intensifying dynamic excitations aided to judge their performance at various intensity levels. Since, up to now, the ET method has not been considered to evaluate the performance of the structures designed by the DDBD approach, this paper addresses this issue. The ET performance curves of RC frames show that structures designed by the DDBD approach in accordance with TBEC-2018 exhibit higher Interstory Drift Ratios (IDRs) values than TSC-2007 at various hazard levels.Article Citation - WoS: 7Citation - Scopus: 7A Comprehensive Study on Burst Pressure Performance of Aluminum Liner for Hydrogen Storage Vessels(ASME, 2021) Kangal, Serkan; Sayı, Abdülmecit Harun; Ayakdaş, Ozan; Kartav, Osman; Aydın, Levent; Artem, Hatice Seçil; Aktaş, Engin; Yücetürk, Kutay; Tanoğlu, Metin; Kandemir, Sinan; Beylergil, BertanThis paper presents a comparative study on the burst pressure performance of aluminum (Al) liner for type-III composite overwrapped pressure vessels (COPVs). In the analysis, the vessels were loaded with increasing internal pressure up to the burst pressure level. In the analytical part of the study, the burst pressure of the cylindrical part was predicted based on the modified von Mises, Tresca, and average shear stress criterion (ASSC). In the numerical analysis, a finite element (FE) model was established in order to predict the behavior of the vessel as a function of increasing internal pressure and determine the final burst. The Al pressure vessels made of Al-6061-T6 alloy with a capacity of 5 L were designed. The manufacturing of the metallic vessels was purchased from a metal forming company. The experimental study was conducted by pressurizing the Al vessels until the burst failure occurred. The radial and axial strain behaviors were monitored at various locations on the vessels during loading. The results obtained through analytical, numerical, and experimental work were compared. The average experimental burst pressure of the vessels was found to be 279 bar. The experimental strain data were compared with the results of the FE analysis. The results indicated that the FE analysis and ASSC-based elastoplastic analytical approaches yielded the best predictions which are within 2.2% of the experimental burst failure values. It was also found that the elastic analysis underestimated the burst failure results; however, it was effective for determining the critical regions over the vessel structure. The strain behavior of the vessels obtained through experimental investigations was well correlated with those predicted through FE analysis.Article Citation - WoS: 2Citation - Scopus: 2Reliability of Corroded Steel Members Subjected To Elastic Lateral Torsional Buckling(Korean Society of Steel Construction, 2021) Uzun, Ertuğrul Türker; Aktaş, EnginStructural steel members are subjected to corrosion due to environmental condition. As a result, there is decreasing in the cross-section properties of the member. This causes different stability problems and reduction in the load carrying capacity of members. Then, the probability of failure, P-f increases due to corrosion. The need arises to determine expected level of safety for such members and systems. Besides, reliability of the steel structure is also effected by the structural stability problems that result decreasing in the resistance. Lateral torsional buckling is one of the most encountered problems in steel members and affected by the critical moment which is a function of lateral and torsional stiffness. Critical moment depends on the material properties, boundary conditions, unbraced length, load pattern, and the member's cross section. Under the corrosion, it is inevitable to observe changing in some of properties. In this study, a damage model to determine the reliability of a corroded I-shape steel member under linear moment gradient is developed considering corrosion exposure time. Uniform and varying thickness loss models are considered to show the corrosion effect. Influence of environmental condition on the load carrying capacity of the members is considered and their effects on member design is evaluated. As a result, it is concluded that load carrying capacity of steel members degrades and safety of them adversely effected. With presented formulas, it is ensured that the load carrying capacity and reliability indices of the steel members can be calculated practically under the examined situationsArticle Citation - WoS: 3Citation - Scopus: 5Helenistik Kulelerde Yanal Yüke İlişkin Düzlem İçi ve Düzlem Dışı Duvar Davranışının Duvar Profilleri ve Açıklık Düzenlerine Bağlı Olarak İncelenmesi(Gazi Üniversitesi, 2020) Gençer, Funda; Turan, Mine; Aktaş, EnginDry masonry wall profiles constructed without using bonding material between blocks are encountered in different building types dated to Greek, Hellenistic and Roman periods. Depending on development of earthquake experiences, dry masonry wall profiles vary in terms of wall thickness, number of layers, relationship of layers and size, form, organization and relationship of blocks. In this study, the construction details increasing the structural strength in watch towers constructed in Hellenistic Period are aimed to be determined. This study is limited with investigation of effect of wall profiles and opening organizations on in-plane and out-of-plane wall behaviors under lateral loading. Primarily, wall profiles and opening types of dry masonry towers in ancient Caria, Pamphylia and Cilicia regions, that have not lost authenticity and integrity or had information about their authentic form, were documented. By using gathered data, hypothetic towers with different wall profiles and opening types are designed. To determine in-plane and out-of-plane wall behavior of hypothetic towers, simulation of quasi-static tilt analysis based on equilibrium were carried out, and form changes at walls and collapse angles of towers were identified. Wall profile and opening properties effecting on structural strength under lateral loading were determinedd.Article Citation - Scopus: 4Betonarme Çerçeve Yapıların Olasılıklı Sismik Analizi(Gazi Üniversitesi, 2006) Korkmaz, Armağan; Aktaş, EnginBetonarme çerçeve yapıların sismik davranışlarının belirlenmesinde, analizlere olasılıklı ifadelerin dahil edilmesi, sismik davranışın daha gerçekçi tanımlanmasına yardımıcı olacaktır. Çalışmada betonarme çerçeve yapıların olasılıklı sismik analizlerinin gerçekleştirilmesi amaçlanmış, bu amaçla örnek betonarme çerçeve yapılar ele alınmıştır. Bu betonarme çerçeve yapılar için öteleme analizleri DRAIN 2D programı ile yapılmıştır. Öteleme analizlerinin ardından zaman tanım alanında dinamik analizler gerçekleştirilmiştir. Öteleme analizleri, zaman tanım alanında dinamik analiz sonuçları ile karşılaştırılmıştır. Bu karşılaştırmanın ardından kırılganlık analizleri yapılmıştır. Betonarme çerçeve yapıların olasılıklı sismik davranışını ortaya koymak amacı ile kırılganlık analizleri ile kırılganlık eğrileri elde edilmiştir. Çalışmanın ana amacı, öteleme analizleri ile zaman tanım alanında dinamik analizlerin karşılaştırılması sonucu, daha gerçekçi bir sismik davranış tanımlama ihtiyacının olduğunu göstermek ve kırılganlık analizleri ile, sismik davranışın olasılıklı olarak daha gerçekçi bir şekilde ifadesini sağlayabilmektir.Article Citation - WoS: 16Citation - Scopus: 24Developing Polymer Composite-Based Leaf Spring Systems for Automotive Industry(Walter de Gruyter GmbH, 2018) Öztoprak, Nahit; Güneş, Mehmet Deniz; Tanoğlu, Metin; Aktaş, Engin; Eğilmez, Oğuz Özgür; Şenocak, Çiler; Kulaç, GedizComposite-based mono-leaf spring systems were designed and manufactured to replace existing mono-leaf metal leaf spring in a light commercial vehicle. In this study, experimentally obtained mechanical properties of different fiber-reinforced polymer materials are presented first, followed by the description of the finite element analytical model created in Abaqus 6.12-1 (Dassault Systemes Simulia Corp., RI, US) using the obtained properties. The results from the finite element analysis are presented next and compared with actual size experimental tests conducted on manufactured prototypes. The results demonstrated that the reinforcement type and orientation dramatically influenced the spring rate. The prototypes showed significant weight reduction of about 80% with improved mechanical properties. The hybrid composite systems can be utilized for composite-based leaf springs with considerable mechanical performance.Article Citation - Scopus: 11A Novel Planar Scissor Structure Transforming Between Concave and Convex Configurations(WITPress, 2017) Yar, Müjde; Korkmaz, Koray; Kiper, Gökhan; Maden, Feray; Akgün, Yenal; Aktaş, EnginIn this paper, a novel two-dimensional scissor structure that transforms between concave and convex configurations is presented. The structure is designed by a method of assembling kite or anti-kite loops in the flat configuration. Angulated units are generated from the assembled loops. Finally, a new angulated scissor unit is introduced in order to design the novel scissor structure.