Civil Engineering / İnşaat Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/13
Browse
348 results
Search Results
Now showing 1 - 10 of 348
Article Citation - Scopus: 1Anomalous Crustal Structure Beneath the Örenli-Eğiller Depression Zone, Inferred From Magnetotelluric Studies, Western Anatolia, Türkiye(TÜBİTAK - Türkiye Bilimsel ve Teknolojik Araştırma Kurumu, 2024) Chandrasekharam, Dornadula; Raju, K.; Subba Rao, P.B.V.; Baba, AlperIn Türkiye, the prevalence of high radiogenic granites makes them ideal locations for initiating enhanced geothermal system (EGS) projects. One such occurrence of these granites is observed in the Kozak area of the Bergama region. To assess the energy potential of this site, a magnetotelluric (MT) survey was conducted, focusing on determining the depth distribution of the intrusive granite. The survey employed dimensionality analysis, utilizing Bahr skew and phase tensor analyses that denote a 2D subsurface nature up to 100 s and beyond that a 3D nature. In the present study, we interpreted MT data up to 100 s. The data collected, including rotated impedance tensors and tippers, were inverted using a nonlinear conjugate gradient algorithm integrated into the MT interpretation software of the WinG Link 2D inversion data modeling package. Multiple homogeneous half-space initial models were tested during the 2D inversion process. The findings indicate the existence of a midcrustal conductor associated with graphites and iron sulfides in the source region. This conductivity may be attributed to processes such as exsolution of metamorphic fluids, influx of mantle sources, or the entry of magmatic fluids through transcrustal fault zones. The findings indicate that the intrusive granite was emplaced along a NE–SW major fault, penetrating shallow crustal levels. The depth of this granite intrusion is determined to be 15 km, covering an outcrop area of 60 km². This detailed geological information allows a comprehensive assessment of the power-generating capacity of the intrusive granite. The results of this investigation contribute valuable insights for the development and optimization of Enhanced Geothermal System (EGS) projects in the region. © 2024, TUBITAK. All rights reserved.Article Citation - WoS: 18Citation - Scopus: 18In-Depth Exploration of Temperature Trends in Morocco: Combining Traditional Methods of Mann Kendall With Innovative Ita and Ipta Approaches(Springer Basel Ag, 2024) Qadem, Zohair; Tayfur, GökmenThis study examines trends in minimum and maximum temperatures at various climate stations located in different regions of Morocco for a period of five decades (1970 to 2019). Mann-Kendall, Sen's estimator, Innovative Trend Analysis (ITA) and Innovative Polygon Trend Analysis (IPTA) were used in the analysis. The results show significant fluctuations, at different time scales, between minimum and maximum temperatures at all stations. In coastal areas, such as Rabat Sale, minimum temperatures fell during January and February while other months saw increases. Average minimum temperatures in Rabat Sale tend to fall by 0.5 degree celsius. On the other hand, maximum temperatures in Rabat Sale rose by 0.2 degrees C. A decrease of 0.4 degree celsius for T-min and 1.6 degree celsius for T-max were observed in higher continental regions, such as Meknes. Other stations, such as Fez Sais (0.6 degree celsius T-min and 2.6 degree celsius T-max) and Taza (1.1 degree celsius T-min and 2.6 degree celsius T-max) showed an upward trend. Trends also vary, with notable increases in minimum and maximum temperatures, indicating different climatic dynamics according to altitude and locality. In particular, the ITA highlights a significant increase in annual maximum temperatures, with a P-value < 0.05 and trend slopes ranging from 0.0015 degree celsius per year in Rabat Sale to 0.0076 degree celsius per year in Taza. In addition, the IPTA results confirm diversity of upward and downward trends on monthly and seasonal scales, highlighting impact of geographical factors such as proximity to sea, topography, and continentality that contribute to formation of regional microclimates. The results highlight significant impact of climate change in Morocco.Review Citation - WoS: 19Citation - Scopus: 22Water Dams: From Ancient To Present Times and Into the Future(MDPI, 2024) Angelakis, Andreas N.; Baba, Alper; Valipour, Mohammad; Dietrich, Jorg; Fallah-Mehdipour, Elahe; Krasilnikoff, Jens; Ahmed, Abdelkader T.Since ancient times, dams have been built to store water, control rivers, and irrigate agricultural land to meet human needs. By the end of the 19th century, hydroelectric power stations arose and extended the purposes of dams. Today, dams can be seen as part of the renewable energy supply infrastructure. The word dam comes from French and is defined in dictionaries using words like strange, dike, and obstacle. In other words, a dam is a structure that stores water and directs it to the desired location, with a dam being built in front of river valleys. Dams built on rivers serve various purposes such as the supply of drinking water, agricultural irrigation, flood control, the supply of industrial water, power generation, recreation, the movement control of solids, and fisheries. Dams can also be built in a catchment area to capture and store the rainwater in arid and semi-arid areas. Dams can be built from concrete or natural materials such as earth and rock. There are various types of dams: embankment dams (earth-fill dams, rock-fill dams, and rock-fill dams with concrete faces) and rigid dams (gravity dams, rolled compacted concrete dams, arch dams, and buttress dams). A gravity dam is a straight wall of stone masonry or earthen material that can withstand the full force of the water pressure. In other words, the pressure of the water transfers the vertical compressive forces and horizontal shear forces to the foundations beneath the dam. The strength of a gravity dam ultimately depends on its weight and the strength of its foundations. Most dams built in ancient times were constructed as gravity dams. An arch dam, on the other hand, has a convex curved surface that faces the water. The forces generated by the water pressure are transferred to the sides of the structure by horizontal lines. The horizontal, normal, and shear forces resist the weight at the edges. When viewed in a horizontal section, an arch dam has a curved shape. This type of dam can also resist water pressure due to its particular shape that allows the transfer of the forces generated by the stored water to the rock foundations. This article takes a detailed look at hydraulic engineering in dams over the millennia. Lessons should be learned from the successful and unsuccessful applications and operations of dams. Water resource managers, policymakers, and stakeholders can use these lessons to achieve sustainable development goals in times of climate change and water crisis.Article Art and Construction Related Qualities of 14th‒15th Century Monuments in a Rural Landscape on the Western Coast of Türkiye(KeAi Communications Co., 2024) Hamamcıoğlu Turan, Mine; Aktaş, Engin; Toköz, Özge DenizThis study aims to contribute to the understanding of the evolution of art and construction in the early settlements established by Turkish communities on the far west Asian coast by focusing on two developed examples in Urla Peninsula. Conventional surveying and evaluation techniques of architectural restoration and civil engineering were utilized. Key findings include the understanding of the hierarchy of rural settlements in the studied landscape: old Çesme the most developed village of peninsula in the 16th century. It was positioned along a valley in distance to coast, but in control of harbor that played significant role in commerce between Europe and Asia. Its mosque and tomb, dated to late 14th – early 15th centuries, used to crown it. Cylindrical minaret tower of mosque, domed tomb tower on a cubical base and squinch in the transition zone of mosque are evidences for Central Asian roots. Usage of local lime stone, re-usage of andesite blocks, framing of the stone blocks with bricks, and pendentive in tomb refer to Roman-Byzantine constructions. The study presents the development of Turkish art and construction on the far west Asian coast in the 14th‒15th centuries. Findings will be a guide for related conservation management in similar contexts. © 2024 The Author(s)Article Citation - Scopus: 2Application of Endurance Time Method in Seismic Assessment of Rc Frames Designed by Direct Displacement-Based Procedure(Turkish Chamber of Civil Engineers, 2024) Karımzada, Nisar Ahmad; Shırkhanı, Amir; Aktaş, EnginThis paper addresses the Direct Displacement-Based Design (DDBD) approach of multi-story RC frame structures consistent with changes to design criteria between Turkish earthquake codes of TSC-2007 and TBEC-2018. The corresponding response modification factor (R) of structures designed based on the DDBD approach is also estimated in this research. The design base shear forces of both codes are compared considering different R factors and also with that of the DDBD approach. The results showed that the DDBD approach, as per TBEC-2018, provides RC frame structures with higher R values compared to the similar approach in accordance with TSC-2007. The Endurance Time (ET) method is a time history-based procedure for seismic assessment of structures under intensifying dynamic excitations aided to judge their performance at various intensity levels. Since, up to now, the ET method has not been considered to evaluate the performance of the structures designed by the DDBD approach, this paper addresses this issue. The ET performance curves of RC frames show that structures designed by the DDBD approach in accordance with TBEC-2018 exhibit higher Interstory Drift Ratios (IDRs) values than TSC-2007 at various hazard levels.Article Citation - WoS: 38Citation - Scopus: 43Quantitative Evaluation of the Damage To Rc Buildings Caused by the 2023 Southeast Turkey Earthquake Sequence(SAGE Publications, 2024) Pujol, Santiago; Bedirhanoğlu, İdris; Dönmez, Cemalettin; Dowgala, Jeffrey D.; Eryılmaz Yıldırım, Meltem; Klaboe, Kari; Köroğlu, Fahri Baran; Lequesne, Rémy D.; Öztürk, Baki; Pledger, Liam; Sönmez, EgemenData from 15 earthquakes that occurred in 12 different countries are presented showing that, without better drift control, structures built with building codes allowing large seismic drifts are likely to keep leaving a wide wake of damage ranging from cracked partitions to building overturning. Following the earthquake sequence affecting southeast Turkey in 2023, a team led by Committee 133 of the American Concrete Institute surveyed nearly 250 reinforced concrete buildings in the area extending from Antakya to Malatya. Buildings ranging from 2 to 16 stories were surveyed to assess their damage and evaluate the robustness of their structures in relation to overall stiffness, as measured by the relative cross-sectional areas of structural walls and columns. The majority of the buildings were estimated to have been built in the past 10 years. Yet, the structures surveyed were observed to have amounts of structural walls and columns comparable with amounts reported after the Erzincan (1992), Duzce (1999), and Bingol (2003) Earthquakes in Turkey. These amounts are, on average, much smaller than the wall and column amounts used in Chile and Japan. Because of that lack of robustness and given the intensities of the motions reported from Antakya to Malatya (with 10 stations with peak ground velocity (PGV) of 100 cm/s or more), it is concluded that structures in this region experienced large drifts. Excessive drift (1) exposed a myriad of construction and detailing problems leading to severe structural damage and collapse, (2) induced overturning caused by p-delta for some buildings, and (3) caused widespread damage to brittle masonry partitions. The main lesson is simple: ductility is necessary but not sufficient. It is urgent that seismic drift limits are tightened in high-seismicity regions worldwide. © The Author(s) 2024.Article Citation - WoS: 3Citation - Scopus: 3Ensemble and Optimized Hybrid Algorithms Through Runge Kutta Optimizer for Sewer Sediment Transport Modeling Using a Data Pre-Processing Approach(Elsevier, 2023) Safari, Mir Jafar Sadegh; Gül, Enes; Dursun, Ömer Faruk; Tayfur, GökmenUncontrolled sediment deposition in drainage and sewer systems raises unexpected maintenance expenditures. To this end, implementation of an accurate model relying on effective parameters involved is a reliable benchmark. In this study, three machine learning techniques, namely extreme learning machine (ELM), multilayer perceptron neural network (MLPNN), and M5P model tree (M5PMT); and three optimization approaches of Runge Kutta (RUN), genetic algorithm (GA), and particle swarm optimization (PSO) are applied for modeling. The optimization and ensemble hybridization approaches are applied in the modeling procedure. For the case of hybrid optimized models, the ELM and MLPNN models are hybridized with RUN, GA, and PSO algorithms to develop six hybrid models of ELM-RUN, ELM-GA, ELM-PSO, MLPNN-RUN, MLPNN-GA, and MLPNN-PSO. Ensemble hybrid models are developed through coupling the ELM and MLPNN models with the M5PMT algorithm. The data pre-processing approach is applied to find the best randomness characteristic of the utilized data. Results illustrate that the RUN-based hybrid models outperform the GA- and PSO-based counterparts. Although the MLPNN-RUN and MLPNN-M5PMT hybrid models generate better results than their alternatives, MLPNN-M5PMT slightly outperforms MLPNN-RUN model with a coefficient of determination of 0.84 and a root mean square error of 0.88. The current study shows the superiority of the ensemble-based approach to the optimization techniques. Further investigation is needed by considering alternative optimization techniques to enhance sediment transport modeling. © 2023 International Research and Training Centre on Erosion and Sedimentation/the World Association for Sedimentation and Erosion ResearchArticle Citation - WoS: 7Citation - Scopus: 5Meteorological Drought and Trend Effects on Transboundary River Basins in Afghanistan(Springer, 2023) Hayat, Ehsanullah; Tayfur, GökmenAfghanistan, as a landlocked country located within central and southwestern Asia, has an arid to semi-arid climate. Most of the people are involved in agricultural activities, and a major part of the country's gross domestic product depends on agriculture, but the country has the lowest water storage capacity. Consecutive periods of drought and rapid snowmelt due to climate change have made it more challenging for suitable water resource management practices. This study investigates the historical meteorological drought characteristics across the whole country by employing the Reconnaissance Drought Index for the period 1979-2019 using data from 55 meteorological stations. Trends in precipitation and temperature are also investigated using the Mann-Kendall's and the Sen's slope statistical tests. A four-decadal countrywide drought map is generated. Extreme and severe droughts were observed in 1999 and 2000 across the whole country. Moderate drought events have started to occur with a frequency of 3 to 5 years since 1999. The decadal annual rainfall values in each river basin indicate that rainfall has decreased in the last two decades with a significant decline in 1999-2008. The trends of increase in temperature and decrease in precipitation are indications of rapid climate change in the country, especially in the south, west, and southwest regions. Due to the intensity and frequency of the droughts, river flow rates have decreased; and therefore, there is a need for the upstream and downstream neighboring countries to come to terms with the phenomenon of a new normal in the hydrological cycle and accordingly revise new water sharing treaties.Article Modeling Plasticity and Damage in Fiber Reinforced Composites by a Crystal Plasticity Based Approach(Elsevier, 2023) Dizman, E. Aybars; Özdemir, IzzetIn very thin ply laminates, delamination failure initiation occurs at much higher stress levels as compared to conventional ply laminates. This results in significant plastic deformation in the matrix accompanied by large fiber rotations. A closer look reveals that microstructure of fiber reinforced composites at large strains do not rotate with the plastic spin induced by the total deformation gradient and therefore inelasticity of such materials requires dedicated constitutive models. This paper focuses on inelastic response of such composites by using a recently proposed crystal plasticity based modeling framework and extents it by a non-local continuum damage mechanics formulation. As opposed to existing works related to composites, adapted crystal plasticity model is formulated and implemented in an implicit manner. To address the initiation and evolution of damage observed at large strains, localizing implicit gradient damage (LIGD) framework is used to degrade the slip resistance and hardening mechanisms on longitudinal and transverse slip systems by means of two separate damage variables. A user element (UEL) subroutine encapsulating all the components of the model is developed and integrated within the commercial finite element solver Abaqus. Capabilities of the model are assessed at material point, ply, and component levels by comparisons with analytical solutions and selected experimental results from the literature.Article Citation - WoS: 7Citation - Scopus: 7Investigating the Effects of Pa66 Electrospun Nanofibers Layered Within an Adhesive Composite Joint Fabricated Under Autoclave Curing(American Chemical Society, 2023) Esenoğlu, Gözde; Tanoğlu, Metin; Barışık, Murat; İplikçi, Hande; Yeke, Melisa; Nuhoğlu, Kaan; Türkdoğan, Ceren; Martin, Seçkin; Aktaş, Engin; Dehneliler, Serkan; Gürbüz, Ahmet Ayberk; İriş, Mehmet ErdemEnhancing the performance of adhesively joined composite components is crucial for various industrial applications. In this study, polyamide 66 (PA66) nanofibers produced by electrospinning were coated on unidirectional carbon/epoxy prepregs to increase the bond strength of the composites. Carbon/epoxy prepregs with/without PA66 nanofiber coating on the bonding region were fabricated using the autoclave, which is often used in the aerospace industry. The single lap shear Charpy impact energy and Mode-I fracture toughness tests were employed to examine the effects of PA66 nanofibers on the mechanical properties of the joint region. Scanning electron microscopy (SEM) was used to investigate the nanofiber morphology and fracture modes. The thermal characteristics of Polyamide 66 nanofibers were explored by using differential scanning calorimetry (DSC). We observed that the electrospun PA66 nanofiber coating on the prepreg surfaces substantially improves the joint strength. Results revealed that the single lap shear and Charpy impact strength values of the composite joint are increased by about 79 and 24%, respectively, by coating PA66 nanofibers onto the joining region. The results also showed that by coating PA66 nanofibers, the Mode-I fracture toughness value was improved by about 107% while the glass transition temperature remained constant.