Civil Engineering / İnşaat Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/13
Browse
3 results
Search Results
Now showing 1 - 3 of 3
Article Citation - WoS: 15Citation - Scopus: 17Effects of Nanosecond Laser Ablation Parameters on Surface Modification of Carbon Fiber Reinforced Polymer Composites(SAGE Publications, 2023) Martin, Seçkin; İplikçi, Hande; Barışık, Murat; Türkdoğan, Ceren; Yeke, Melisa; Nuhoğlu, Kaan; Esenoğlu, Gözde; Tanoğlu, Metin; Aktaş, Engin; Dehneliler, Serkan; İriş, Mehmet ErdemRemoval of contaminants and top polymer layer from the surface of carbon-fiber-reinforced polymer (CFRP) composites is critical for high-quality adhesive-joining with direct bonding to the reinforcing fiber constituents. Surface treatment with a laser beam provides selective removal of the polymer matrix without damaging the fibers and increasing the wettability. However, inhomogeneous thermal properties of CFRP make control of laser ablation difficult as the laser energy absorbed by the carbon fibers is converted into heat and transmitted through the fiber structures during the laser operation. In this study, the effect of scanning speed and laser power on nanosecond laser surface treatment was characterized by scanning electron microscope images and wetting angle measurements. Low scanning speeds allowed laser energy to be conducted as thermal energy through the fibers, which resulted in less epoxy matrix removal and substantial thermal damage. Low laser power partially degraded the epoxy the surface while the high power damaged the carbon fibers. For the studied CFRP specimens consisting of unidirectional [45/0/?45/90]2s stacking of carbon/epoxy prepregs (HexPly®-M91), 100 mJ/mm2 generated by 10 m/s scanning speed and 30 W power appeared as optimum processing parameters for the complete removal of epoxy matrix from the top surface with mostly undamaged carbon fibers and super hydrophilic surface condition. © The Author(s) 2023.Article Citation - WoS: 11Citation - Scopus: 12Cement Based Strain Sensor: a Step To Smart Concrete(Foundation Cement, Lime, Concrete, 2011) Teomete, Egemen; Erdem, Tahir KemalAccording to a report published in USA, 30% of the bridges in USA were found to be structurally de cient while concrete infrastructures have a state of material deterioration before the design life is reached (1). Earthquakes, material degradations and other environmental effects decrease the performance of the structures. The assessment of structures by structural health monitoring is very important to protect the lives of people. The best decision about a damaged structure after an earthquake can be made by use of structural tests and structural health monitoring. Structural tests and structural health monitoring are important steps in the decision making of asset management for maintenance and repair of infrastructures. The classical sensors (strain gauges, piezo-electric sensors) have low durability, low sensitivity and high cost. The low durability of classical sensors disables long term measurement while their high cost limits the amount of sensors that can be used (2). The addition of carbon ber to cement based material decreases the electrical resistance of the material. By application of load, the electrical resistance of the material changes (3-5).Article Citation - WoS: 31Citation - Scopus: 33Modification of Carbon Fibre/Epoxy Composites by Polyvinyl Alcohol (pva) Based Electrospun Nanofibres(Adcotec Ltd., 2016) Beylergil, Bertan; Tanoğlu, Metin; Aktaş, EnginIn this study, the effects of modifying interlaminar region of unidirectional carbon fibre/epoxy composites by the incorporation of electrospun polyvinyl alcohol (PVA) nanofibres were investigated. PVA nanofibres were directly deposited onto the carbon fabrics by electrospinning method to improve mechanical performance of those composites. The features of the electrospun nanofibres were characterized by microscopy techniques. The unidirectional carbon fibre/epoxy composite laminates with/without PVA nanofibre interlayers were manufactured by vacuum-infusion technique in a [0]4 configuration. Tensile, three-point bending, compression, Charpy-impact and Mode-I fracture toughness tests (Double Cantilever Beam (DCB)) were carried out in accordance with ASTM standards to evaluate mechanical performance of the composites. Scanning electron microscopy (SEM) observations were made on the specimens to evaluate microstructural features. It was observed that the carbon fabrics were successfully coated with a thin layer of PVA nanofibres by electrospinning technique. The results showed that P VA nanofibres improve the mechanical properties of unidirectional carbon/epoxy composite laminates when subjected to in-plane loading. On the other hand, PVA nanofibres slightly reduced the mode-I fracture toughness values although they led to more stable crack propagation.