WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7150
Browse
4 results
Search Results
Article Citation - WoS: 15Citation - Scopus: 17Effect of Substrate Rotation Speed and Off-Center Deposition on the Structural, Optical, and Electrical Properties of Azo Thin Films Fabricated by Dc Magnetron Sputtering(American Institute of Physics, 2018) Aygün, Gülnur; Aygün, Gülnur; Köseoğlu, Hasan; Özdemir, Mehtap; Özdemir, Mehtap; Özyüzer, Lütfi; Özyüzer, Lütfi; Özyüzer, Gülnur Aygün; Özyüzer, Lütfi; 04.05. Department of Pyhsics; 04. Faculty of Science; 01. Izmir Institute of TechnologyIn this study, aluminum-doped zinc oxide (AZO) thin films were deposited by DC magnetron sputtering at room temperature. The distance between the substrate and target axis, and substrate rotation speed were varied to get high quality AZO thin films. The influences of these deposition parameters on the structural, optical, and electrical properties of the fabricated films were investigated by X-ray diffraction (XRD), Raman spectroscopy, spectrophotometry, and four-point probe techniques. The overall analysis revealed that both sample position and substrate rotation speed are effective in changing the optical, structural, and electrical properties of the AZO thin films. We further observed that stress in the films can be significantly reduced by off-center deposition and rotating the sample holder during the deposition. An average transmittance above 85% in the visible range and a resistivity of 2.02 × 10-3Ω cm were obtained for the AZO films.Article Citation - WoS: 266Citation - Scopus: 292High Quality Ito Thin Films Grown by Dc and Rf Sputtering Without Oxygen(IOP Publishing Ltd., 2010) Tuna, Öcal; Özyüzer, Lütfi; Selamet, Yusuf; Selamet, Yusuf; Aygün, Gülnur; Aygün, Gülnur; Özyüzer, Lütfi; 04.05. Department of Pyhsics; 04. Faculty of Science; 01. Izmir Institute of TechnologyHigh quality indium tin oxide (ITO) thin films were grown without oxygen by both dc and RF magnetron sputtering techniques on glass substrates. The effects of substrate temperature, film thickness and sputtering method on the structural, electrical and optical properties of the as-grown films were investigated. The results showed that the substrate temperature had substantial effects on the film properties, in particular on the crystallization and resistivity. When the substrate temperature was increased to 150 °C, crystallization in the (2 2 2) plane started appearing for both dc and RF sputtered films. We additionally found that with further increments of substrate temperature, the preferred crystallization orientation changed differently for dc and RF sputtered films. Optical transmission in the visible region for a film thickness of 70 nm was found to be above 85%. The bandgap was calculated to be about 3.64 eV for the substrate temperature of 150 °C for a 70 nm thick film. The value of the bandgap increased with respect to the increment in film thickness as well as substrate temperature. We also measured the temperature dependence of the resistivity and Hall coefficient of the films, and calculated the carrier concentration and Hall mobility. Very low room temperature resistivities for dc and RF magnetron sputtered grown films of about 1.28 × 10-4 Ω cm and 1.29 × 10-4 Ω cm, respectively, were obtained. © 2010 IOP Publishing Ltd.Article Citation - WoS: 15Citation - Scopus: 13Impact of temperature increments on tunneling barrier height and effective electron mass for plasma nitrided thin Sio2 layer on a large wafer area(American Institute of Physics, 2010) Aygün, Gülnur; Aygün, Gülnur; Erlbacher, T.; Wolf, M.; Schellenberger, M.; Pfitzner, L.; 04.05. Department of Pyhsics; 04. Faculty of Science; 01. Izmir Institute of TechnologyThermally grown SiO2 layers were treated by a plasma nitridation process realized in a vertical furnace. The combination of a pulsed-low frequency plasma and a microwave remote plasma with N2/NH 3/He feed gas mixture was used to nitride the thermally grown SiO2 gate dielectrics of MIS structures. Temperature dependency of effective masses and the barrier heights for electrons in pure thermally grown SiO2 as well as plasma nitrided SiO2 in high electric field by means of Fowler-Nordheim regime was determined. It is frequently seen from the literature that either effective electron mass or barrier height (generally effective electron mass) is assumed to be a constant and, as a result, the second parameter is calculated under the chosen assumption. However, in contrast to general attitude of previous studies, this work does not make any such assumptions for the calculation of neither of these two important parameters of an oxide at temperature ranges from 23 to 110 °C for SiO 2, and 23 to 130 °C for nitrided oxide. It is also shown here that both parameters are affected from the temperature changes; respectively, the barrier height decreases while the effective mass increases as a result of elevated temperature in both pure SiO2 and plasma nitrided SiO 2. Therefore, one parameter could be miscalculated if the other parameter, i.e., effective mass of electron, was assumed to be a constant with respect to variable physical conditions like changing temperature. Additionally, the barrier heights were calculated just by taking constant effective masses for both types of oxides to be able to compare our results to common literature values. © 2010 American Institute of Physics.Article Citation - WoS: 14Citation - Scopus: 18Xps Study of Pulsed Nd:yag Laser Oxidized Si(Elsevier Ltd., 2006) Özyüzer, Gülnur Aygün; Aygün, Gülnur; Atanassova, Elenada A.; Kostov, K.; Turan, Raşit; 04.05. Department of Pyhsics; 04. Faculty of Science; 01. Izmir Institute of TechnologyX-ray photoelectron spectra (XPS) of thin SiO2 layers grown by pulsed Nd:YAG laser at a substrate temperature of 748 K are presented. The peak decomposition technique combined with depth profiling is employed to identify the composition and chemical states of the film structure. It is established that the oxide is non-stoichiometric, and contains all oxidation states of Si in different amounts throughout the film. The interface Si/laser-grown oxide is not abrupt, and the coexistence of Si2O3 and Si2O suboxides in a relatively wide interfacial region is found. It is concluded that post-oxidation annealing is necessary in order to improve the microstructure of both oxide and near interface region.