WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7150
Browse
2 results
Search Results
Article Citation - WoS: 63Citation - Scopus: 72Ito/Au Multilayer Thin Films on Transparent Polycarbonate With Enhanced Emi Shielding Properties(Elsevier, 2020) Erdoğan, Nursev; Özyüzer, Lütfi; Erden, Fuat; Özdemir, Mehtap; Astarlıoğlu, A. Taner; Aygün, Gülnur; Özdemir, Mehtap; Özbay, Salih; Aygün, Gülnur; Özyüzer, Lütfi; 04.05. Department of Pyhsics; 04. Faculty of Science; 01. Izmir Institute of TechnologyITO/Au/ITO multilayer thin films were deposited onto polycarbonate substrate via magnetron sputtering technique without intentional heating. The deposition times of both ITO and Au layers were studied to optimize the overall transparency and conductivity. As-prepared thin films were characterized using X-ray diffraction analysis, secondary ion mass spectroscopy, scanning and transmission electron microscopy, atomic force microscopy and physical property measurement system. The optical measurement results revealed that the transmittance of the films were enhanced by increasing the gold deposition time up to 15 s. Beyond this point, further increasing the duration caused a decrease in optical transmittance. Upon optimization of the Au deposition time, the deposition duration of ITO layers was also studied to increase electromagnetic interference (EMI) shielding effectiveness (SE). Maximum EMI SE in this work was measured as 26.8 dB, yielding 99.8% power attenuation, which was verified by simulation results.Article Citation - WoS: 22Citation - Scopus: 23Effect of Heat Treating Metallic Constituents on the Properties of Cu2znsnse4 Thin Films Formed by a Two-Stage Process(Elsevier Ltd., 2017) Olgar, Mehmet Ali; Başol, B. M.; Aygün, Gülnur; Özyüzer, Lütfi; Aygün, Gülnur; Özyüzer, Lütfi; Bacaksız, Emin; 04.05. Department of Pyhsics; 04. Faculty of Science; 01. Izmir Institute of TechnologyIn this study Cu2ZnSnSe4 (CZTSe) thin films were grown by a two-stage process that involved sputter deposition of a Cu/Sn/Zn/Cu metallic stack, annealing the stack at various temperatures for 30 min, evaporation of a Se cap over the metallic stack thus forming a precursor layer, and subjecting the precursor layer to a final high temperature reaction step at 550 °C. Different samples were prepared with annealing temperatures of the metallic stacks ranging from 200 °C to 350 °C. The results showed that heat treatment of the metallic stacks did not cause much change in their morphology and elemental composition, however their phase content changed noticeably when the anneal temperature was raised to 250 °C. Specifically, while the metallic films were dominated by CuSn and Cu5Zn8 phases at low temperatures, the dominant phase shifted to Cu6Sn5 at the annealing temperature of 250 °C and higher. Also formation of a distinct Cu3Zn2 phase was observed upon annealing at temperatures at or above 250 °C. After reaction with Se, the CZTSe layer obtained from the metallic film, which was annealed at 250 °C was found to be the best n terms of its composition, crystalline quality and purity, although it contained a small amount of CuSe. The other layers were found to contain small amounts of other secondary phases such as SnSe, CuSe2, ZnSe and Cu2SnSe3. SEM micrographs showed denser structure for CZTSe layers grown from metallic films annealed at or above 250 °C. Optical band gap, resistivity and carrier concentration of the best quality CZTSe film were found to be about 0.87 eV, 2 Ω-cm and 4 × 1017 cm− 3, respectively.