WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7150
Browse
2 results
Search Results
Article Citation - WoS: 6Citation - Scopus: 5Structural and Optical Characteristics of Antimony Selenosulfide Thin Films Prepared by Two-Step Method(Springer, 2022) Türkoğlu, Fulya; Ekren, Memduh Emirhan; Özyüzer, Lütfi; Yakıncı, Kübra; Aygün, Gülnur; Aygün, Gülnur; Özyüzer, Lütfi; 04.05. Department of Pyhsics; 04. Faculty of Science; 01. Izmir Institute of TechnologyAntimony triselenide (Sb2Se3) is one of the most promising absorber material choices among the inorganic semiconductors that has attracted much attention today. However, highest recorded efficiencies for Sb2Se3 solar cells are still lower than ideal. Exploring antimony selenosulfide (Sb-2(SxSe1-x)(3)) to increase device performance is one option because some features of alloyed Sb-2(SxSe1-x)(3) depend on composition such as bandgap and band position. In this study, two-step process was used to grow Sb-2(SxSe1-x)(3) thin films. In the first stage, Sb2Se3 thin films were deposited on soda lime glass substrates using direct current magnetron sputtering technique. In the second stage, Sb2Se3 thin films were exposed to sulfurization process in a quartz ampoule to obtain Sb-2(SxSe1-x)(3) thin films. Characterization results showed that morphological, optical, and structural properties of Sb-2(SxSe1-x)(3) thin films grown by presented method were highly dependent on amount of sulfur in the films. By the adjustment of the S/S + Se atomic ratio, Sb-2(SxSe1-x)(3) absorber materials with suitable bandgap, favorable orientation and compact morphology can be obtained for photovoltaic applications.Article Citation - WoS: 22Citation - Scopus: 23Effect of Heat Treating Metallic Constituents on the Properties of Cu2znsnse4 Thin Films Formed by a Two-Stage Process(Elsevier Ltd., 2017) Olgar, Mehmet Ali; Başol, B. M.; Aygün, Gülnur; Özyüzer, Lütfi; Aygün, Gülnur; Özyüzer, Lütfi; Bacaksız, Emin; 04.05. Department of Pyhsics; 04. Faculty of Science; 01. Izmir Institute of TechnologyIn this study Cu2ZnSnSe4 (CZTSe) thin films were grown by a two-stage process that involved sputter deposition of a Cu/Sn/Zn/Cu metallic stack, annealing the stack at various temperatures for 30 min, evaporation of a Se cap over the metallic stack thus forming a precursor layer, and subjecting the precursor layer to a final high temperature reaction step at 550 °C. Different samples were prepared with annealing temperatures of the metallic stacks ranging from 200 °C to 350 °C. The results showed that heat treatment of the metallic stacks did not cause much change in their morphology and elemental composition, however their phase content changed noticeably when the anneal temperature was raised to 250 °C. Specifically, while the metallic films were dominated by CuSn and Cu5Zn8 phases at low temperatures, the dominant phase shifted to Cu6Sn5 at the annealing temperature of 250 °C and higher. Also formation of a distinct Cu3Zn2 phase was observed upon annealing at temperatures at or above 250 °C. After reaction with Se, the CZTSe layer obtained from the metallic film, which was annealed at 250 °C was found to be the best n terms of its composition, crystalline quality and purity, although it contained a small amount of CuSe. The other layers were found to contain small amounts of other secondary phases such as SnSe, CuSe2, ZnSe and Cu2SnSe3. SEM micrographs showed denser structure for CZTSe layers grown from metallic films annealed at or above 250 °C. Optical band gap, resistivity and carrier concentration of the best quality CZTSe film were found to be about 0.87 eV, 2 Ω-cm and 4 × 1017 cm− 3, respectively.