WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection

Permanent URI for this collectionhttps://hdl.handle.net/11147/7150

Browse

Filters

2004 - 200912010 - 20202

Settings

Author: search.filters.author.Tanoğlu, MetinDepartment: search.filters.department.İzmir Institute of Technology. Materials Science and Engineering

Search Results

Now showing 1 - 3 of 3
  • Article
    Citation - WoS: 1
    Interfacial Properties of Aluminum/Glass-fiber Reinforced Polypropylene Sandwich Composites
    (Springer Verlag, 2013) Baştürk, S. B.; Tanoğlu, Metin; Guruşçu, A.; Tanoğlu, Metin; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of Technology
    Aluminum/glass-fiber-reinforced polypropylene (Al/GFPP) laminates were manufactured by using various surface pretreatment techniques. Adhesion at the composite/metal interface was achieved by a surface pretreatment of Al sheets with amino-based silane coupling agents, incorporation of a polyolefin-based adhesive film and modification with a PP-based film containing 20 wt.% of maleic-anhydride-modified polypropylene (PP-g-MA). In order to increase the effect of bonding between components of the laminates, the combination of silane treatment and the addition of the PP-based film was also investigated. The mechanical properties (shear, peel, and bending strengths) of adhesively bonded Al/GFPP laminates were examined to evaluate the effects of the surface treatments mentioned. It was revealed that the adhesion in the laminated Al/GFPP systems could be improved by the treatment of aluminum surface with an amino-based silane coupling agent. Judging from the results of peel and bending strength, with incorporation of polyolefin-based films, adhesion in the Al/GFPP laminates increased significantly. The modification of Al/GFPP interfaces with a PP-g-MA/PP layer led to the highest improvement in their adhesion properties. The combination of surface modification with silane and addition of PP-based films did not yield the high bending strength desired. This may be due to the insufficient bonding between silane groups and PP-based films.
  • Article
    Citation - WoS: 11
    Citation - Scopus: 13
    Effect of Cnt Incorporation on Pan/Ppy Nanofibers Synthesized by Electrospinning Method
    (TÜBİTAK, 2020) İnce Yardımcı, Atike; Selamet, Yusuf; Tanoğlu, Metin; Tanoğlu, Metin; Yılmaz, Selahattin; Yılmaz, Selahattin; Selamet, Yusuf; 03.02. Department of Chemical Engineering; 03.10. Department of Mechanical Engineering; 04.05. Department of Pyhsics; 03. Faculty of Engineering; 04. Faculty of Science; 01. Izmir Institute of Technology
    In this study, carbon nanotubes (CNTs) added polyacrylonitrile/polypyrrole (PAN/PPy) electrospun nanofibers were produced. Average diameters of the nanofibers were measured as 268 and 153 nm for 10 and 25 wt% of PPy contents, respectively. A relatively higher strain to failure values (23.3%) were observed for the low PPy content. When as-grown CNTs (1 and 4 wt%) were added into the PAN/PPy blends, disordered nanofibers were observed to form within the microstructure. To improve the interfacial properties of CNTs/PAN/PPy composites, CNTs were functionalized with H2SO4/HNO3/HCl solution. The functionalized CNTs were well dispersed within the nanofibers and aligned along the direction of nanofibers. Therefore, beads formation on nanofibers decreased. The impedance of the nanofibers was found to decrease with the PPy content and CNT addition. These nanofibers had a great potential to be used as an electrochemical actuator or a tissue engineering scaffold.
  • Conference Object
    Microstructure-Performance Relation in Pmma-Based Open-Cell Porous Materials for High Pressure Ceramic Sanitaryware Casting
    (Trans Tech Publications, 2004) Ergün, Yelda; Dirier, C.; Tanoğlu, Metin; Tokman, C.; Tanoğlu, Metin; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of Technology
    The ceramic whiteware/sanitaryware industry is rapidly undergoing to implement high-pressure casting techniques for ceramic article production. In these techniques, materials with open pore microstructure that allows drainage of water under applied pressure are needed. The polymethyl methacrylate (PMMA) based polymeric porous materials have become the most suitable type of materials for this purpose because of their short casting periods and high service lives. However, the superior service life and performance of these materials are closely related to the microstructure. In the present study, the porous materials with various compositions of the constituents in the emulsion were produced to effect the microstructure of PMMA-based materials. The variations on the pore microstructure were interrelated to the performance of the material for high-pressure sanitaryware casting. The pore morphology and water permeability of the samples was measured using optical and SEM microscopy and permeability measurement techniques, respectively. The compressive collapse stress and modulus values were determined by performing compression testing. The results showed a significant interrelation between microstructure and the performance of the PMMA-based ceramic mould materials.