WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7150
Browse
2 results
Search Results
Article Citation - Scopus: 1Assessing the Density of Wood in Heritage Buildings’ Elements Through Expedited Semi-Destructive Techniques(Multidisciplinary Digital Publishing Institute (MDPI), 2025) Şen, Ali Umut; Sen, Ali Umut; Gomes, Maria da Gloria; 01. Izmir Institute of TechnologyFeatured Application The research presented and justified in this text aims to provide agents involved in the conservation and refurbishment of old timber elements in buildings with a correlation table for interpreting the readings obtained with penetration resistance testing equipment.Abstract Historically, wood has been among the main materials used in heritage buildings. However, the species and mechanical properties of these elements are often unknown. This uncertainty complicates safety assessment calculations, aggravated by the natural variability of the wood properties. The aim of this work is to assess the density of wooden elements in service using semi-destructive techniques that retain the integrity of structural elements. This research had two phases. First, penetration resistance tests were carried out on laboratory scale on Pinus sylvestris L. wood samples taken from 18th, 19th, and 20th century heritage buildings in Lisbon, Portugal. Later, a field study was carried out on wooden elements from the same buildings, involving needle penetration, core drilling, and moisture content determination tests. The laboratory test results showed a strong correlation between the needle penetration depth and wood density, with an R2 value of 0.76. The results of the field study indicated that the density estimated by the needle penetration test correlated effectively with the measured density of extracted cores after moisture correction, with an R2 of 0.99. In conclusion, the experimental results confirm that penetration resistance and moisture tests are reliable and practical for estimating wood density under in-service conditions.Conference Object Citation - WoS: 22Citation - Scopus: 24Characterization of Poly(vinyl Chloride) Powder Produced by Emulsion Polymerization(Springer Verlag, 2010) Atakul Savrık, Sevdiye; Balköse, Devrim; Ülkü, Semra; Ülkü, Semra; Balköse, Devrim; 03.02. Department of Chemical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologyThe effect of emulsion process formulation ingredients on the morphology, structure, and properties of polyvinyl chloride (PVC) powder has been considered in this study. PVC powder was extracted with ethanol and films were obtained by solvent casting from tetrahydrofurane. Characterization of powders, films, and ethanol extract was performed through FTIR spectroscopy, DSC, AFM, SEM, EDX analysis, methylene blue, and nitrogen adsorption. PVC powder was composed of spheres of a large particle size range from 10 nm to 20 μm as shown by SEM. The specific surface area of the PVC powder was determined as 16 and 12 m 2 g-1 from methylene blue adsorption at 25 °C and from N2 adsorption at -196 °C, respectively. AFM indicated the surface roughness of the films obtained by pressing the particles was 25.9 nm. Density of PVC powder was determined by helium pycnometry as 1.39 g cm -3. FTIR spectroscopy indicated that it contained carbonyl and carboxylate groups belonging to additives such as surface active agents, plasticizers, and antioxidants used in production of PVC. These additives were 1.6% in mass of PVC as determined by ethanol extraction. EDX analysis showed PVC particles surfaces were coated with carbon-rich materials. The coatings had plasticizer effect since, glass transition temperature was lower than 25 °C for PVC powder and it was 80 °C for ethanol extracted powders as found by using differential scanning calorimetry. These additives from polymerization process made PVC powder more thermally stable as understood from Metrom PVC thermomat tests as well. © 2010 Akadémiai Kiadó, Budapest, Hungary.