WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection

Permanent URI for this collectionhttps://hdl.handle.net/11147/7150

Browse

Filters

2019 - 20202

Settings

Subject: search.filters.subject.Microtomography

Search Results

Now showing 1 - 2 of 2
  • Article
    Citation - WoS: 23
    Citation - Scopus: 23
    Hot Air Permeable Preceramic Polymer Derived Reticulated Ceramic Foams
    (American Chemical Society, 2020) de Mello Innocentini, Murilo Daniel; Ahmetoğlu, Çekdar Vakıf; Marsola, Gabriel Antonio; Orlandi Lasso, Paulo Renato; Soraru, Gian Domenico; Semerci, Tuğçe; Vakıfahmetoğlu, Çekdar; 03.09. Department of Materials Science and Engineering; 03. Faculty of Engineering; 01. Izmir Institute of Technology
    Open and partially closed cell polymer derived ceramic, specifically silicon oxycarbide, foams were produced from commercially available polyurethane (PU) foams through the replica technique combined with the preceramic polymer pyrolysis route. The focus was directed on the role of PU morphology (cell size and open/partially closed cells), synthesis parameters (cross-linking temperature and time), and type of the polysiloxane precursors for fine-tuning the microstructural features of the resulting ceramic foams and their eventual effect on the fluid dynamic/mechanical properties. Consequently, ceramic foams having dense/hollow struts with/without hierarchical porosity were able to be manufactured and characterized in detail. The average total porosity including all compositions was above 95%, the maximum surface area was found to be reaching 79 m(2).g(-1), and the room temperature permeability measurements indicated a wide range for k(1) (0.28 x 10(-9)-11.48 x 10(-9) m(2)) and k(2) (0.34 x 10(-5)-54.17 x 10(-5) m) according to the selected PU substrate. Hot air permeation tests showed that the foams were stable up to 700 degrees C without any loss of functionality. Accordingly, they are envisioned to be employed as reusable air filtration device parts for pollutants (viruses, bacteria, dust, etc.), catalytic supports, and filter components for reactions occurring in aggressive environments.
  • Article
    Citation - WoS: 6
    Citation - Scopus: 6
    A Study on Numerical Determination of Permeability and Inetia Coefficient of Aluminum Foam Using X-Ray Microtomography Techniques: Focus on Inspection Methods for Reliability (permeability and Inertia Coefficient by Tomography)
    (Begell House, 2019) Mobedi, Moghtada; Mobedi, Moghtada; Nakayama, Akira; Özkol, Ünver; Özkol, Ünver; Çelik, Hasan; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of Technology
    The volume-averaged (i.e., macroscopic) transport properties such as permeability and inertia coefficient of two aluminum foams with 10 and 20 pores per inch (PPI) pore density are found using microtomography images. It is shown that a comparison between the numerical values and the experimental results may not be sufficient to prove the correctness of the obtained results. Hence, in addition to traditional validation methods such as grid independency and comparison with reported results in literature, further inspections such as (a) checking the development of flow, (b) inspection of Darcy and non-Darcy regions, (c) conservation of flow rate through the porous media, (d) sufficiency of number of voxels in the narrow throats, and (e) observation of transverse velocity gradients in pores for high and low Reynolds numbers can be performed to further validate the achieved results. These techniques have been discussed and explained in detail for the performed study. Moreover, the obtained permeability and inertia coefficient values are compared with 19 reported theoretical, numerical, and experimental studies. The maximum deviation between the present results and the reported studies for 10 PPI is below 25%, while for 20 PPI it is below 28%.