WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7150
Browse
3 results
Search Results
Now showing 1 - 3 of 3
Article Citation - WoS: 5Citation - Scopus: 4Influence of Partitioning Treatment on Microstructure and Mechanical Properties of an Alloyed Ductile Iron Austempered at Different Temperatures(Walter de Gruyter GmbH, 2023) Neite, Maximilian; Münstermann, Sebastian; Nalçacı, Burak; Davut, Kemal; Erdoğan, MehmetThe present study was conducted to uncover effects of partitioning treatment on Cu-Ni-Mo alloyed ductile iron (DI) austempered at different temperatures. For this purpose, the DI samples, produced via sand casting, were austenitized at 900 °C for 60 min, followed by austempering at the temperatures of 275-325-375 °C for 120 min and afterwards a partitioning treatment was applied at 200 °C for 15 min. In the characterization studies, dilatometer, image analysis, JMat-Pro, mechanical tests, XRD, optical microscope, and scanning electron microscope (SEM) equipped with EBSD detector were utilized. Characterization studies showed that the effects of partitioning treatment were directly correlated with austempering temperature and high carbon austenite volume fraction changed in the range of 19.48-35.45%. That redistribution of carbon (C) between bainitic ferrite and high carbon austenite occurred, in turn, the carbon content of high carbon austenite increased with the partitioning treatment irrespective of austempering temperature were uncovered. Furthermore, the partitioning treatment considerably changed the grain morphologies of both high carbon austenite and banitic ferrite. As a consequence of these microstructural differences, the highest tensile strength of 1489.2 MPa was established in the sample austempered at 275 °C and partitioned at 200 °C, whereas the highest ductility of 5.61% acquired at the austempering temperature of 375 °C. © 2023 Walter de Gruyter GmbH, Berlin/Boston.Article Citation - WoS: 29Citation - Scopus: 31Effect of Heat Input on Haz Softening in Fiber Laser Welding of 22mnb5 Steel(Elsevier, 2023) Tuncel, Oğuz; Aydın, Hakan; Davut, KemalThis study investigates the effects of heat input on the heat-affected zone (HAZ) softening in fiber laser welding of quenched 1.1 mm thick 22MnB5 steel. Laser power (1500-2500 W) and welding speed (40-120 mm/s) parameters are considered as the input process variables. Depending on the input parameters, the applied heat input varied between 12.5 and 62.5 J/mm. The results indicate that a minimum heat input of 50 J/mm is required for full weld penetration. Microhardness findings revealed that the drop in hardness in the HAZ region relative to the base material (BM) reached 39% due to grain coarsening caused by an increase in heat input under the welding conditions. Grain coarsening (prior austenite grains) is also detected in SEM analysis. In addition, grain coarsening at high heat input was also determined quantitatively in EBSD analyses. The proportion of 8.91 mu m grain size in the sample with high heat input is 4.2%, while it is 1.2% in the sample with low heat input. When the heat input increased from 12.5 to 62.5 J/mm, the width of the softened zone with the lowest hardnesses in the HAZ grew from 0.2 mm to 2.2 mm.Article Citation - WoS: 4Citation - Scopus: 5Effects of Tib2 Nanoparticle Content on the Microstructure and Mechanical Properties of Aluminum Matrix Nanocomposites(Walter de Gruyter GmbH, 2017) Kandemir, SinanThe present work reports the fabrication of A357 alloy matrix nanocomposites reinforced with 0.5, 1.0 and 2.0 wt.-% TiB2 nanoparticles (20-30 nm) by a novel method which is the combination of semi-solid mechanical mixing and ultrasonic dispersion of nanoparticles in liquid state. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicated that reasonably effective deagglomeration and uniform distribution of TiB2 nanoparticles into the matrix were achieved. Transmission electron microscopy studies also confirmed that the nanoparticles were embedded into the matrix and a good bonding was obtained between the matrix and the reinforcement. Increasing nanoparticle content led to grain refinement and significant enhancement in the mechanical properties of nanocomposites. The addition of 0.5, 1.0, and 2.0 wt.-% TiB2 nanoparticles increased the 0.2 % proof stress of matrix alloy by approximately 31, 48 and 61 %, respectively. The contribution of different mechanisms to the strength enhancement is discussed. It is proposed that the strengthening is mainly due to Orowan mechanism and dislocation generation effect by the coefficient of thermal expansion mismatch between the TiB2 nanoparticles and the matrix.