WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7150
Browse
Search Results
Now showing 1 - 6 of 6
Article Citation - WoS: 45Citation - Scopus: 48Recrystallization and Grain Growth Kinetics of In718 Manufactured by Laser Powder Bed Fusion(Elsevier, 2022) Doğu, Merve Nur; Davut, Kemal; Obeidi, Muhannad Ahmed; Yalçın, Mustafa Alp; Gu, Hengfeng; Low, Thaddeus Song En; Ginn, Jon; Brabazon, DermotThe recrystallization and grain growth behaviour of IN718 alloy additively manufactured by laser powder bed fusion (L-PBF) is presented herein. The effects of three different temperatures (1050, 1150 and 1250 °C) and holding times (15, 45 and 90 min) were investigated. The texture evolution of the samples was recorded via electron backscatter diffraction (EBSD). The as-built sample is composed of bowl-shaped melt pools, a chessboard-like grain pattern and has a cube texture {100}<001>. Recrystallized grains were observed in the samples treated at 1150 °C for 15 min, as well as the samples treated for longer periods and at higher temperatures. Recrystallization was observed to start from high dislocation density regions, including the overlapping melt pools and the borders of the chessboard-like pattern. The initial cube texture transforms into a first-generation cube-twin texture {122}<212> via a twinning-assisted recrystallization mechanism. Then, those recrystallization nuclei sweep through the high defect density matrix; during which almost no new twins are formed. The samples treated at 1250 °C are almost completely recrystallized, which forms a weaker cube texture and a stronger P-orientation {011}<112>. However, the growth of recrystallized grains is very limited due to the presence of non-coherent precipitates.Article Citation - WoS: 3Citation - Scopus: 4Partial Austenitisation and Tbf Steel Composed of Ferrite, Bainitic Ferrite, and Austenite(Taylor & Francis, 2022) Erişir, Ersoy; Bilir, Oğuz Gürkan; Sözer, Yunus Emre; Ararat, Özge; Davut, KemalA TRIP-aided bainitic-ferritic (TBF) steel with a chemical composition of Fe-0.19C-1.7Mn-1.09Si-0.51Al-0.05Nb (wt-%) was partially austenitised from a hot-rolled martensitic initial microstructure. After the hot rolling, the martensitic specimens were reheated to different intercritical temperatures and then austempered at 350 degrees C. Thus, the effect of the initial microstructure of TBF steel on intercritical austenite formation during partial austenitisation was studied. The microstructures were investigated by scanning electron microscopy and electron backscatter diffraction (EBSD), and the tensile properties were tested. Microstructural observations revealed that a final microstructure of fine ferrite, bainitic ferrite, and retained austenite can be obtained. The steel partial austenitised at 770 degrees C showed a good combination of ultimate tensile strength and total elongation.Article Citation - WoS: 8Citation - Scopus: 8Design and Fabrication of Polymer Micro/Nano Composites With Two-Level Mechanical Reinforcing Procedure(Wiley, 2022) Kandemir, Ayşe Çağıl; Dönmez, Fatma; Davut, Kemal; Kaplan Can, HaticeBiocompatible composite production was accomplished by utilizing two-level hierarchical approach for mechanical reinforcement. A well-known commodity polymer; low-density polyethylene (LDPE), which has high-fracture toughness, yet low strength and modulus was used as the main matrix material. As the first step of hierarchy, ductile LDPE was blended with brittle polyvinylpyrrolidone (PVP), which is an eco-friendly, nontoxic and biocompatible polymer. This resulted in slight decrease of strength and drastic reduction of toughness (%70), yet modulus was increased by 78%. As the second level of hierarchy, PVP composites were introduced in LDPE. Nano-scaled Halloysite clay and micro-scaled spherical Silica particles were utilized as additives in the aforementioned PVP composites. The reason for the choice of these particles is that they are nontoxic, low-cost and in the case of Halloysite; abundant in nature. Owing to the implementation of the second level; modulus improvement was further enhanced to 150%, with additional benefits of strength increase up to 17% and less reduction in fracture toughness (minimum 51% reduction). Dynamic mechanical analysis also supported these outcomes that storage modulus of composites are higher than both LDPE and LDPE-PVP blend. The proposed biocompatible composites in the end of this study would be utilized in biomedical applications necessitating mechanical improvements.Article Citation - WoS: 6Citation - Scopus: 6A Numerical Methodology for Monitoring Stress Distributions and Experimental Proof of the Concept on Metal Embedded Thin Polymer-Matrix Composites Using X-Ray Diffraction(Elsevier, 2022) Demir, Eralp; Sas, Hatice S.; Işık, Murat; Aydoğan Güngör, Eda; Davut, KemalIn this study, a numerical methodology is developed to monitor stress distributions and an experimental technique is investigated to measure stresses on metal embedded polymer matrix fiber-reinforced composite materials using X-ray diffraction (XRD) method. The numerical method successfully predicts the stress distributions using only a few data points with an average accuracies of 11.6% and 11.8%, respectively for tapered and open hole tensile sample geometries. Experimental part of this study investigates different methodologies to measure stresses on surfaces of polymer composites materials of thin walled structures by XRD. For this reason, metallic materials were integrated onto the surface and near-surface of polymer matrix composites in three different configurations as in the forms of metal foil, metal powder, and metal wire mesh. In-situ experiments of measured and applied stresses revealed metal powder embedded composite materials as a promising material configuration for reliable monitoring of stresses.Article Citation - WoS: 6Citation - Scopus: 6Texture Evolution of Friction Stir-Processed Dual-Phase Steel(Springer, 2022) Aktarer, Semih Mahmut; Küçükömeroğlu, Tevfik; Davut, KemalEvolution of crystallographic texture and local strains in different zones of a dual-phase steel subjected to severe plastic deformation by friction stir process was examined by electron backscatter diffraction technique. Misorientations, which were expressed by the values of grain orientation spread and kernel average misorientation (KAM), increased from the thermomechanical affected zone (TMAZ) to pin-affected stir zone (PE-SZ). KAM maps showed that the highest local strain appeared in the PE-SZ. Misorientation distributions were found to be consistent with microhardness distributions in the processed region. The crystallographic texture of base metal, heat-affected zone, and TMAZ was similar. Recrystallization and deformation texture components were observed at stir zones, and recrystallization texture components decreased drastically at PE-SZ. Rotated cube, goss and rotated goss texture components were detected at PE-SZ. Rotated cube texture component indicates partial recrystallization after plastic deformation. Shear texture components were determined using shear direction (SD) as reference. Different shear texture components (111), (112), and (101)Article Citation - WoS: 39Citation - Scopus: 41Effect of Post Fabrication Aging Treatment on the Microstructure, Crystallographic Texture and Elevated Temperature Mechanical Properties of In718 Alloy Fabricated by Selective Laser Melting(Elsevier, 2022) Özer, Seren; Bilgin, Güney Mert; Davut, Kemal; Esen, Ziya; Dericioğlu, Arcan.FThe effect of building direction and post fabrication aging treatment on the microstructure, crystallographic texture and high temperature mechanical properties of Inconel 718 (IN718) alloy fabricated by selective laser melting (SLM) method was investigated. After aging, arc-shaped structures seen in as-fabricated samples disappeared and converted into a mixture of columnar and equiaxed grains. Nano-sized γ″ and/or γ′ precipitates were formed upon aging; however, MC type carbides and Laves phase encountered in as-fabricated samples were not dissolved completely after aging. Moreover, aging did not alter the texture ((001)//building direction (BD)) of as-fabricated samples. Mechanical properties of the alloys under tension were influenced by the build direction, aging time and test temperature. As-fabricated samples produced in vertical direction exhibited higher room temperature strengths with lower ductility due to orientation of overlapped prior melt pools. Room temperature tensile test results revealed that peak aging caused a significant improvement in ultimate tensile strength (UTS), from 1066.5 MPa and 998.4 MPa to 1408.5 MPa and 1330.4 MPa whereas elongation values decreased from 27.5% and 32.2% to 19.6% and 23.7% in vertically and horizontally built samples, respectively. Peak-aged samples (aged at 700 °C for 8 h) tested at 600 °C displayed serrated regions in their stress-strain curves due to dynamic strain aging (DSA). Although strength values of the samples displayed an expected decrease by temperature, ductility of the samples reduced to minimum at temperatures around 700–800 °C, which was attributed to intermediate temperature embrittlement.