WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection

Permanent URI for this collectionhttps://hdl.handle.net/11147/7150

Browse

Filters

2002 - 2009122010 - 2019142020 - 20234

Settings

COAR Access Rights: search.filters.coarAccessRights.open accessSubject: search.filters.subject.Mechanical properties

Search Results

Now showing 1 - 10 of 30
  • Article
    Citation - WoS: 13
    Citation - Scopus: 16
    Influence of Recycled Carbon Fiber Addition on the Microstructure and Creep Response of Extruded Az91 Magnesium Alloy
    (KeAi Communications Co., 2023) Kandemir, Sinan; Bohlen, Jan; Dieringa, Hajo
    In this study, the recycled short carbon fiber (CF)-reinforced magnesium matrix composites were fabricated using a combination of stir casting and hot extrusion. The objective was to investigate the impact of CF content (2.5 and 5.0 wt.%) and fiber length (100 and 500 µm) on the microstructure, mechanical properties, and creep behavior of AZ91 alloy matrix. The microstructural analysis revealed that the CFs aligned in the extrusion direction resulted in grain and intermetallic refinement within the alloy. In comparison to the unreinforced AZ91 alloy, the composites with 2.5 wt.% CF exhibited an increase in hardness by 16–20% and yield strength by 5–15%, depending on the fiber length, while experiencing a reduction in ductility. When the reinforcement content was increased from 2.5 to 5.0 wt.%, strength values exhibited fluctuations and decline, accompanied by decreased ductility. These divergent outcomes were discussed in relation to fiber length, clustering tendency due to higher reinforcement content, and the presence of interfacial products with micro-cracks at the CF-matrix interface. Tensile creep tests indicated that CFs did not enhance the creep resistance of extruded AZ91 alloy, suggesting that grain boundary sliding is likely the dominant deformation mechanism during creep. © 2023
  • Article
    Citation - WoS: 5
    Citation - Scopus: 6
    Effect of Coiling Temperature on the Structure and Properties of Thermo-Mechanically Rolled S700mc Steel
    (Technical Faculty in Bor, 2022) Di Nunzio, P. E.; Cesile, M. C.; Oktay, S.; Davut, Kemal; Şeşen, M. K.
    The boron-free S700MC steel is usually produced by exploiting the properties of a ferrite-bainite mixed microstructure formed by coiling the strips at a temperature of about 450 degrees C, i.e.below the bainite starting temperature. With the aim of further enhancing the mechanical properties of 6 to 10 mm thick strips, industrial tests were carried out at a coiling temperature of 600 degrees C to promote the formation of a structure of ferrite and carbides, which is also acceptable for this type of steel. Unexpectedly, a microstructure composed of ferrite and martensite was obtained. Compared to the ferritic-bainitic grade, the new structure is characterized by a slight decrease of the yield point but by an increase of the ultimate tensile strength by no less than 80 MPa, with a transition from a quasi-discontinuous to a clearly continuous yielding behaviour. Accordingly, the ratio of yield strength to tensile strength decreases from 0.90 to 0.75 and the impact energy decreases by 35 J and 60 J for the two gauge levels, respectively. The mechanical behaviour of the strips coiled at high temperature is explained as a direct consequence of the dual phase structure with a hard phase interspersed in a soft ferrite matrix. The presence of martensite is explained by the so-called incomplete bainite reaction. The partial transformation into ferrite after coiling and the long time required for the coil to cool down stabilize the untransformed austenite due to the carbon enrichment making bainite formation at lower temperatures impossible.
  • Article
    Citation - WoS: 41
    Citation - Scopus: 45
    High Temperature Tensile, Compression and Creep Behavior of Recycled Short Carbon Fibre Reinforced Az91 Magnesium Alloy Fabricated by a High Shearing Dispersion Technique
    (National Engineering Research Center for Magnesium Alloys of China, Chongqing University, 2021) Kandemir, Sinan; Gavras, Sarkis; Dieringa, Hajo
    The present study seeks the feasibility of using short carbon fibres recycled from polymer matrix composites as alternative to virgin carbon fibres in the reinforcement of magnesium alloys. The microstructures, high temperature mechanical and creep properties of AZ91 alloy and its composites with various recycled carbon fibre contents (2.5 and 5 wt.%) and lengths (100 and 500 ?m) were investigated in the temperature range of 25–200 °C. The microstructural characterization showed that the high shear dispersion technique provided the cast composites with finer grains and relatively homogenous distribution of fibres. The materials tested displayed different behaviour depending on the type of loading. In general, while enhancements in the mechanical properties of composites is attributed to the load bearing and grain refinement effects of fibres, the fluctuations in the properties were discussed on the basis of porosity formation, relatively high reinforcement content leading to fibre clustering and interlayer found between the matrix and reinforcement compared to those of AZ91 alloy. The compressive creep tests revealed similar or higher minimum creep rates in the recycled carbon fibre reinforced AZ91 in comparison to the unreinforced AZ91. © 2021
  • Article
    Citation - WoS: 3
    Citation - Scopus: 3
    Investigations of Flame Retardant Properties of Zinc Borate Accompanying With Huntite and Hydromagnesite in Polymer Composites
    (Polish Mineral Engineering Society, 2020) Atay, Hüsnügül Yılmaz; İçin, Öykü; Kuru, Buket
    Fires have been a danger to human beings for the centuries. As people lost their lives and property in fires, they tried to fight the fire and their efforts in this area continued increasingly. Unfortunately, it is still not possible to completely reset the risk of starting the fire. But it seems likely to extinguish immediately after the fire has started, and this is very important to save people's lives. Scientists have been working in this field in recent years; they are concentrated on producing fire-resistant materials using different materials. This can be provided by different ways; either fire-resistant material can be produced new, or the fire resistivity can be provided by incorporating the additive material into a flammable material. In our previous studies, we used huntite and hydromagnesite minerals to give fire resistance property to polymer materials, very successful results were obtained. In this study, huntite and hydromagnesite minerals were used for accompanying with zinc borate in polypropylene composites in order to increase the flame retardant property of a polymeric materials. Different content of minerals were blended with polypropylene, and composites were produced by twin-screw extruder for observing synergistic effect. Scanning electron microscopy (SEM) analyses were conducted to determine the structural and morphological properties of the composites. Thermal properties were determined according to thermogravimetric analysis (TGA). Tensile and three point bending tests were carried out to obtain mechanical properties. Flame retardant performance was evaluated according to UL 94 vertically flammability test. It was concluded that very good synergistic effects were obtained that zinc borate was significantly influential with huntite/hydromagnesite in the flammability characteristics of composites because higher char formation is observed with zinc borate addtion. Moreover, the zinc borate reduced the smoke generated during combustion.
  • Article
    Citation - WoS: 16
    Citation - Scopus: 24
    Developing Polymer Composite-Based Leaf Spring Systems for Automotive Industry
    (Walter de Gruyter GmbH, 2018) Öztoprak, Nahit; Güneş, Mehmet Deniz; Tanoğlu, Metin; Aktaş, Engin; Eğilmez, Oğuz Özgür; Şenocak, Çiler; Kulaç, Gediz
    Composite-based mono-leaf spring systems were designed and manufactured to replace existing mono-leaf metal leaf spring in a light commercial vehicle. In this study, experimentally obtained mechanical properties of different fiber-reinforced polymer materials are presented first, followed by the description of the finite element analytical model created in Abaqus 6.12-1 (Dassault Systemes Simulia Corp., RI, US) using the obtained properties. The results from the finite element analysis are presented next and compared with actual size experimental tests conducted on manufactured prototypes. The results demonstrated that the reinforcement type and orientation dramatically influenced the spring rate. The prototypes showed significant weight reduction of about 80% with improved mechanical properties. The hybrid composite systems can be utilized for composite-based leaf springs with considerable mechanical performance.
  • Article
    Citation - WoS: 9
    Citation - Scopus: 9
    Synthesis and Characterization of Novel High Temperature Structural Adhesives Based on Nadic End Capped Mda-Btda Copolyimide
    (IOP Publishing Ltd., 2018) Acar, Oktay; Varış, Serhat; Işık, Tuğba; Tirkeş, Seha; Demir, Mustafa Muammer
    A series of novel copolyimide structural adhesives were synthesized using 4,4′-diaminodiphenylmethane (MDA), 3,4′-oxydianiline (ODA) and 3,3′,4,4′-benzophenonetetracarboxylic acid dianhydride (BTDA) as co-monomers, and nadic anhydride as an end cap reagent. The adhesives with different MDA and ODA contents were examined in terms of their structure, thermal stability, mechanical properties, and adhesive performance. They have glass transition temperatures (T g) about 400 °C, with thermal stability up to 500 °C. The effect of diamine monomer compositions on adhesion performance and processability of the copolyimides were studied. The copolyimides exhibited adhesion strength up to 16.3 MPa at room temperature. Nadic end capped MDA-BTDA-ODA copolyimide resins gained adjustable and controllable processability with the addition of ether bridged aromatic segments. The copolyimide adhesive with equimolar composition of MDA:ODA is distinguished form the both commercial PMR-15 and LARC RP-46 polyimides in terms of its better processability and mechanical performance.
  • Article
    Citation - WoS: 14
    Citation - Scopus: 16
    Microstructure and Mechanical Properties of A357/Sic Nanocomposites Fabricated by Ultrasonic Cavitation-Based Dispersion of Ball-Milled Nanoparticles
    (SAGE Publications Inc., 2017) Kandemir, Sinan
    In this work, A357/0.5 wt.% SiC nanocomposites were fabricated with a combination of ultrasonic processing and a nanoparticle feeding mechanism that involves the introduction of a closed end aluminium tube filled with the ball-milled SiC nanoparticles (20-30 nm) and aluminium powders (<75 μm) into the melt for complete deagglomeration and uniform dispersion of nanoparticles through the matrix. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicate that relatively effective deagglomeration and uniform dispersion of SiC nanoparticles into the molten alloy were achieved. The hardness and tensile properties of the nanocomposites were notably improved compared to those of the ultrasonically processed A357 alloy without reinforcement, showing the strengthening potency of nanoparticles and the good bonding obtained at the particle-reinforcement interface.
  • Article
    Citation - WoS: 187
    Citation - Scopus: 266
    Improvement of Barrier and Mechanical Properties of Whey Protein Isolate Based Food Packaging Films by Incorporation of Zein Nanoparticles as a Novel Bionanocomposite
    (Elsevier Ltd., 2016) Oymacı, Pelin; Alsoy Altınkaya, Sacide
    In this study, whey protein isolate (WPI) based bio-nanocomposite films embedded with zein nanoparticles (ZNP) were prepared by solution casting. Nanoparticles were coated with sodium caseinate to obtain a uniform distribution in the films. The mechanical, water vapor barrier, surface wetting, morphological and viscoelastic properties of the films were investigated. The addition of ZNP significantly improved the water vapor barrier and mechanical properties of the WPI without adversely affecting the elongation of the films. Dynamical mechanical analysis and contact angle measurements revealed that upon addition of the nanoparticles, the fractional free volume and hydrophilicity of the WPI films decreased. Sodium caseinate containing both hydrophilic and hydrophobic groups created an efficient interface between the hydrophobic ZNP and hydrophilic WPI matrix, allowing for a homogeneous distribution of nanoparticles even at very high loading levels as evidenced by the scanning electron microscope (SEM) and atomic force microscopy (AFM) images. The WPI/ZNP nanocomposite films can potentially become effective food packaging materials.
  • Article
    Citation - WoS: 55
    Citation - Scopus: 64
    High-Early Ductile Cementitious Composites With Characteristics of Low Early-Age Shrinkage for Repair of Infrastructures
    (Springer Verlag, 2015) Şahmaran, Mustafa; Al-Emam, Muhannad; Yıldırım, Gürkan; Şimşek, Yunus Emre; Erdem, Tahir Kemal; Lachemi, Mohamed
    Reduced performance in concrete infrastructures is mainly caused by the formation of cracks, which may arise due to deteriorating mechanisms during service life. In most cases, reduced performance calls for urgent repairs to the degraded section. Therefore, it is highly desirable to develop dimensionally stable, ductile repair materials that can attain adequately high strength in a limited amount of time, compensate for significant deformation due to mechanical and environmental loadings, and prevent early-age shrinkage cracks. In this paper, the performance of such a material (high-early-strength engineered cementitious composites, HES-ECC, with very low early-age shrinkage capacity) was investigated by studying mechanical properties and dimensional stability. Composites were produced with different water to cementitious materials and slag to Portland cement ratios. In order to enhance composite properties in terms of ductility and early-age shrinkage characteristics, saturated lightweight aggregates replaced sand in the mixtures. The experimental results show that the majority of HES-ECC mixtures developed in this study attained compressive strength values of more than 20.0 MPa and minimum flexural strength of 6.0 MPa within 6 h. Moreover, the HES-ECC mixtures exhibited strain-hardening behavior with strain capacities comparable to normal strength ECC, as well as substantially reduced autogenous shrinkage strain, both of which are unlikely to trigger the formation of cracks in tension at early ages. The integration of these conflicting parameters suggests that HES-ECC can easily meet the need for fast and durable repairs.
  • Article
    Citation - WoS: 166
    Citation - Scopus: 170
    Mechanical Properties of Monolayer Gas and Gase Crystals
    (American Physical Society, 2016) Yağmurcukardeş, Mehmet; Senger, Ramazan Tuğrul; Peeters, François M.; Şahin, Hasan
    The mechanical properties of monolayer GaS and GaSe crystals are investigated in terms of their elastic constants: in-plane stiffness (C), Poisson ratio (ν), and ultimate strength (σU) by means of first-principles calculations. The calculated elastic constants are compared with those of graphene and monolayer MoS2. Our results indicate that monolayer GaS is a stiffer material than monolayer GaSe crystals due to the more ionic character of the Ga-S bonds than the Ga-Se bonds. Although their Poisson ratio values are very close to each other, 0.26 and 0.25 for GaS and GaSe, respectively, monolayer GaS is a stronger material than monolayer GaSe due to its slightly higher σU value. However, GaS and GaSe crystals are found to be more ductile and flexible materials than graphene and MoS2. We have also analyzed the band-gap response of GaS and GaSe monolayers to biaxial tensile strain and predicted a semiconductor-metal crossover after 17% and 14% applied strain, respectively, for monolayer GaS and GaSe. In addition, we investigated how the mechanical properties are affected by charging. We found that the flexibility of single layer GaS and GaSe displays a sharp increase under 0.1e/cell charging due to the repulsive interactions between extra charges located on chalcogen atoms. These charging-controllable mechanical properties of single layers of GaS and GaSe can be of potential use for electromechanical applications. © 2016 American Physical Society.