WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7150
Browse
67 results
Search Results
Now showing 1 - 10 of 67
Article Effects of Span 60 Template and Freeze Drying on Zinc Borate Produced From Zinc Nitrate Hexahydrate and Borax Decahydrate(Taylor and Francis Ltd., 2022) Alp, Burcu; Gönen, Mehmet; Atakul Savrık, Sevdiye; Balköse, DevrimZinc borate is an important additive to polymers and lubricants. The process variables such as reactant concentration, presence of template in precipitating medium and drying method determine the composition and particle size of zinc borates. In the present study, zinc borate precipitate obtained by mixing aqueous zinc nitrate and borax decahydrate solutions was dried either by conventional method or by freeze drying. The products were well characterized by advanced methods. Zinc borate from 1 mol dm(-3) reactants had (2.1 +/- 0.5)x(2.5 +/- 0.5)x(1.3 +/- 0.2) mu m and (0.5 +/- 0.1)x(1.3 +/- 0.1)x(0.028 +/- 0.01) mu m dimensions by conventional and freeze drying respectively. Individual particles smaller in size is obtained since the particles are not agglomerated due to absence of surface tension of liquid water for case of freeze drying. Planar particles agglomerated into 20 to 60 mu m crystals in the presence of template Span 60 in 1 mol dm(-3) reactants for conventional drying. Nano zinc borate particles with primary particle size of (46 +/- 9) nm were obtained by decreasing the reactant concentration to 0.1 mol dm(-3). The primary particle size was decreased to (40 +/- 3) nm by addition of Span 60 to dilute solutions. However zinc borate nanoparticles obtained from dilute solutions adhered to each other forming agglomerates during conventional drying. Their freeze drying would allow formation of a freely flowing nano powder.Article Citation - WoS: 14Supercritical Ethanol Drying of Zinc Borates of 2zno Center Dot 3b(2)o(3)center Dot 3h(2)o and Zno Center Dot B2o3 Center Dot 2h(2)o(Elsevier Ltd., 2011) Gönen, Mehmet; Balköse, Devrim; Ülkü, SemraSupercritical ethanol (SCE) drying of zinc borates was investigated to obtain dry zinc borate nanoparticles and to elucidate possible chemical interactions between zinc borates and ethanol. Commercial and synthesized 2ZnO center dot 3B(2)O(3)center dot 3H(2)O and ZnO center dot B2O3 center dot 2H(2)O samples were dried by both conventional and SCE drying methods and the products were compared. Zinc borates were characterized using X-ray powder diffraction (XRD), thermo gravimetric analysis (TGA), Fourier transform infrared (FTIR) analysis, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and helium pycnometer. Zn and B contents of samples were also determined by analytical titration. It was found that zinc borate of ZnO center dot B2O3 center dot 2H(2)O decomposed completely into zinc oxide and boric acid. However, zinc borate having oxide formula of 2ZnO center dot 3B(2)O(3)center dot 3H(2)O decomposed partially to form anhydrous zinc borate, zinc oxide, water and boric acid during the SCE drying carried out at 250 degrees C and 6.5 MPa. Boric acid and water were extracted from both of zinc borates by supercritical ethanol. The extraction of boric acid by ethanol in the SCE drying of zinc borates is an important result which can be utilized in the production of boric acid from water insoluble natural minerals, e.g. colemanite. The boric acid-ethanol solution could be directly utilized in the synthesis of ethyl borate. (C) 2011 Elsevier B.V. All rights reserved.Book Part Key Engineering Materials Volume I: Current State of the Art on Novel Materials(Taylor and Francis Ltd., 2014) Balköse, Devrim; Horak, Daniel; Soltes, Ladislav[No abstract available]Book Citation - Scopus: 5Aluminium-Coated Polymer Films as Infrared Light Shields for Food Packing(Apple Academic Press, 2014) Hamrang, Abbas; Balköse, Devrim; Zaikov, Gennadij Efremovich; Haghi, A. K.This book covers a broad range of polymeric materials and provides industry professionals and researchers in polymer science and technology with a single, comprehensive book summarizing all aspects involved in the functional materials production chain. This volume presents the latest developments and trends in advanced polymer materials and structures. It discusses the developments of advanced polymers and respective tools to characterize and predict the material properties and behavior. This book has an important role in advancing polymer materials in macro and nanoscale. Its aim is to provide original, theoretical, and important experimental results that use non-routine methodologies. It also includes chapters on novel applications of more familiar experimental techniques and analyses of composite problems that indicate the need for new experimental approaches. This new book: • Provides a collection of articles that highlight some important areas of current interest in key polymeric materials and technology. • Gives an up-to-date and thorough exposition of the present state of the art of key polymeric materials and technology. • Describes the types of techniques now available to the engineers and technicians and discusses their capabilities, limitations, and applications. • Provides a balance between materials science and chemical aspects, basic and applied research. • Focuses on topics with more advanced methods. • Emphasizes precise mathematical development and actual experimental details. • Explains modification methods for changing of different materials properties. © 2020 Elsevier B.V., All rights reserved.Article Citation - WoS: 5Citation - Scopus: 7Effect of the Zeolite Filler on the Thermal Degradation Kinetics of Polypropylene(Scibulcom Ltd., 2006) Tıhmınlıoğlu, Funda; Pehlivan, Hilal; Balköse, Devrim; Ülkü, SemraIn this study, the thermal degradation behaviour of polypropylene (PP) and polypropylene-zeolite composites was investigated. Clinoptilolite, a natural zeolitic tuff, was used as the filling material into the composites. Effect of both pure clinoptilolite and silver ion exchanged form of clinoptilolite addition on the thermal degradation kinetics of polypropylene composites was studied by using differential scanning calorimetry (DSC) and thermal gravimetry analysis (TGA) techniques. Polymer degradation was evaluated by using DSC with heating rates of 5, 10, and 20 degrees C/ min from room temperature up to 500 degrees C. Silver concentration (4.36, 27.85 and 183.8 mg Ag/g zeolite) was the selected parameter under consideration. From the DSC curves, it was observed that the heat of degradation values of the composites containing 2-6% silver exchanged zeolites (321-390 kJ/kg) were larger compared to that of the pure PP free of silver and zeolite (258 kJ/kg). From the DSC results it was confirmed that PP-zeolite composites can be used at higher temperatures compared to the pure PP polymer because of its higher thermal stability. The thermal decomposition activation energies of the composites were calculated by using both the Kissenger and Ozawa models. The values predicted from these two equations were in close agreement. From the TGA curves, it was found that zeolite addition into the PP matrix speeds down the decomposition reaction, however, silver exchanged zeolite addition into the matrix accelerates the reaction. The higher the silver concentration, the lower the thermal decomposition activation energies were obtained. As a result, PP was found to be much more susceptible to thermal decomposition in the presence of silver exchanged zeolite.Article Citation - WoS: 5Citation - Scopus: 6Use, Preparation, and Characterization of Copper-Containing Silica Gel(American Chemical Society, 2020) Ulutan, Sevgi; Tüzüm Demir, Ayşe Pınar; Balköse, DevrimThe preparation and characterization of humidity-indicating silica gel containing copper sulfate were aimed at in the present study. The equilibrium and kinetics of Cu(II) sorption were investigated by contacting 200-1600 mg dm(-3) Cu ion-containing solutions with silica hydrogel slabs having 10% silica. The diffusion coefficient of Cu(II) in silica hydrogel was determined to be on the order of 10(-10) m(2) s(-1). X-ray diffraction indicated that the gels contained mainly CuSO4 center dot 3H(2)O, CuSO4 center dot H2O, and small amounts of CuSO4 and CuSiO3 center dot 2H(2)O. The silica gel with Cu(II) can be used as a humidity indicator since its color changes from light blue to dark blue upon moisture adsorption.Article Citation - WoS: 6Citation - Scopus: 9Preparation and Characterization of Flexible Polyvinylchloride-Copper Composite Films(Smithers Rapra Technology, 2013) Kurt, Emrah; Özçelik, Cenk Yağız; Yetgin, Senem; Özmıhçı Ömürlü, Filiz; Balköse, DevrimFlexible PVC films are statically charged due to their low electrical conductivity. This creates fire threat during its handling. Conductive materials are added to films to prevent this. In the present study it was aimed to prepare PVC- copper composite films by sol gel technique and characterize the prepared films. It was aimed to increase the electrical conductivity of the films by adding copper powder. However, the copper particles settled down to bottom instead of forming a conductive network that covers the whole cross section. Thus at the film crosssection a plastic upper phase and a copper rich lower phase were present. The film did not conduct electricity due to this uneven distribution. The minimum volumetric and surface resistivities of the films were at the order of 109 ohm-cm and 1010 ohm square respectively.Article Citation - WoS: 2Citation - Scopus: 10Water and Water Vapor Sorption Studies in Poly(propylene)-Zeolite Composites(John Wiley and Sons Inc., 2003) Pehlivan, Hilal; Özmıhçı, Filiz; Tıhmınlıoğlu, Funda; Balköse, Devrim; Ülkü, SemraWater and water vapor sorption to porous poly(propylene)zeolite composites prepared by hot pressing have been studied as a function of zeolite loading. This work presents the first report on the effect of the zeolite as a filler on the water sorption properties of PP composites. Water swelling experiments were conducted at 25°C using pure PP and PP-zeolite film samples having different zeolite loadings (6-40 wt%). Since PP is a hydrophobic polymer, it does not sorp any water, but the composites having 10, 20, 30, and 40% zeolite sorbed 0.63, 1.00, 1.72 and 3.74 wt% water, respectively. The zeolite itself at the same conditions sorbed 24.5 wt% water. As the filler loading in the composites increased, equilibrium uptake values increased too. On the other hand, water vapor sorption and kinetics has been studied using a Cahn 2000 gravimetric sorption system. Within in the range 0.35-0.95%, water vapor was adsorbed by the composites containing 10-40 wt% zeolite. Experimental effective water vapor diffusivities of the composite films were about one order of magnitude higher than the experimental water diffusion coefficient in composites. The transport of water in composites was slower than that in the liquid water due to the longer diffusion pathway and adsorption on the surface of the composites. Although the liquid water may fill all the voids in the composite, water vapor is adsorbed on the surface of the zeolite only.Article Citation - WoS: 4Citation - Scopus: 5Dynamic Heat of Adsorption of Water Vapour on Zeolitic Tuff and Zeolite 4a by Flow Microcalorimetry(Scibulcom Ltd., 2006) Ülkü, Semra; Balköse, Devrim; Alp, BurcuIn this study a practical method for measurement of heat of adsorption of water vapour on adsorbents was developed to evaluate the feasibility of substitution of a zeolitic tuff with zeolite 4A in air drying and heat pumps. The change of heat of adsorption with inlet humidity of the air passing through the calorimeter was investigated. Samples were characterised by X-ray diffraction and thermal gravimetric analysis techniques. Specific heats of the zeolitic tuff and zeolite 4A were measured as 1.01 and 1.42 J/g K, respectively. Adsorption isotherms fitted to the Langmuir model with regression coefficient 0.93 and 0.94 with monolayer capacities, Xm 9.68% and 26.35% H 2O for the zeolitic tuff and zeolite 4A, respectively. The energy storage intensity was measured in the range 48-97 J/g and 464-201 J/g for the tuff and zeolite 4A, respectively. Heat of adsorption of zeolite decreased with surface coverage and it was in the range 1750-2835 and 1104-2640 J/g H 2O for the zeolitic tuff and zeolite 4A, respectively.Article Citation - WoS: 2Citation - Scopus: 2A Study of Chemical and Physical Changes During Biaxially Oriented Polypropylene Film Production(Walter de Gruyter GmbH, 2003) Ülkü, Semra; Balköse, Devrim; Arkış, Esen; Sipahioğlu, MuzafferPolypropylene films obtained during the biaxial orientation process were characterized by energy dispersive X-ray analysis (EDX), scanning electron microscopy. X-ray diffraction, differential scanning calorimetry, infrared spectroscopy. Inorganic particles with Al, Si, Na, Mg, Ti, K,O elements were present in biaxially oriented films. Polypropylene had molecules with both isotactic configuration and it was crystallized only in isotactic α phase. The films drawn in one and two directions had unit cells with b axis parallel to surface of the films. The antioxidants present in the films were consumed during processing, preventing polypropylene oxidation in air at high processing temperatures. One surface of the films contained less polypropylene and had functional groups rich in oxygen such as C=O and COO.