WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7150
Browse
31 results
Filters
Settings
Search Results
Now showing 1 - 10 of 31
Article Preparation and Characterization of Hydroxyapatite Reinforced Polymeric Scaffolds(Natl Inst Science Communication-NISCAIR, 2025) Firata, Duygu Doga; Ersoz, Su Turku; Burcu Alp, Fatma; Cetin, Ali Emrah; Ciftcioglu, MuhsinPorous HA reinforced PLA/PCL scaffolds with polymer volume percentages in the 7.0-7.6 range have been prepared by solvent-casting/salt leaching technique. The scaffolds have been characterized by conducting gravimetric measurements, FTIR analysis, TGA, X-ray diffraction analysis, compression tests, cell viability tests, and thermal and hydrolytic degradation tests in order to investigate the effect of PLA/PCL, PLA/HA, PCL/HA and PLA/PCL/HA blending on scaffold properties. Porosity of the scaffolds has been determined to be in the 83-92 percent range. The scaffold porosity has decreased with HA content. The water absorption of the scaffolds has been found to be in between 400 and 750%. The yield strength and the elastic modulus of the scaffolds have been determined to be in the 0.001-0.02 and 5.6-10.6 MPa ranges, respectively. The yield strength of the scaffolds has increased by both PCL and HA contents whereas elastic modulus has increased with PCL content but has decreased with HA content. Mechanical test results have indicated that the addition of HA has increased the strength of the scaffolds while decreasing their flexibility. The activation energies for the thermal degradation of the scaffolds have been determined to be in the 130-398 kJ/mol range and have been shown to be a function of PCL, PLA, and HA content. The hydrolytic degradation behavior of the scaffolds in acetate buffer solutions (pH=4.5) during 127 days and XRD analysis have indicated that the hydrolytic degradation occurring in the amorphous part of the surface film has been diffusion-controlled. The diffusion coefficients of the degradation products in the scaffolds have been estimated to be in the 1.21-4.95x10(-13) m(2)/s range. Cell viability test results have indicated that the composition of the composite scaffold structure has played a determining role in the prepared scaffolds.Article Citation - WoS: 6Citation - Scopus: 6Inverse Effects of Lanthanide Co-Doping on the Photocatalytic Hydrogen Production and Dye Degradation Activities of Cu Doped Sol-Gel Tio<sub>2</Sub>(Elsevier, 2023) Yurtsever, Husnu Arda; Erzin, Kubilay; Ciftcioglu, Muhsin; Yurtsever, Hüsnü Arda; Erzin, Kubilay; Çiftçioğlu, MuhsinCopper doped and lanthanide-copper co-doped titania powders were prepared by sol-gel technique and the effects of co-doping on the photocatalytic reduction and oxidation activities of titania were investigated in this work. Characterization studies indicated that a reduced structure was formed due to the presence of Ti3+ species in copper doped titania powder and a more stable structure was formed when lanthanides were used as co-dopants. Copper doped powder had a significantly higher activity in photocatalytic hydrogen production (1037 mu mol/g/h) than the co-doped powders (similar to 400 mu mol/g/h). The oxidation activities of co-doped powders however were determined to be about 2 times higher than that of the copper doped powder. The decrease in the reduction activity was attributed to the decrease in the number of Ti3+ sites, whereas the increase in oxidation activity was probably a result of the increase in the surface area and dye adsorption due to lanthanide co-doping.Article Impact of Titania Phase Structure and Surface Reactivity on the Photocatalytic Degradation of Various Dyes and Textile Wastewater(National Institute of Science Communication and Policy Research, 2023) Yurtsever, Hüsnü Arda; İloğlu, Onur; Çiftçioğlu, MuhsinTitania (TiO2) powders have been prepared by precipitation method in different precipitation media which contain sulfate, nitrate or organic species. Photocatalytic degradation of different dyes and a real textile wastewater have been conducted with these powders along with commercial powder Degussa P25 for comparison. Ethyl alcohol (organic medium), sulfuric acid (sulfate medium) and nitric acid (nitrate medium) have been used to dissolve titanium precursor for the precipitation of TiO2 in ammonia solution. UV-Vis DRS and XPS results indicate that S doping in sulfate medium precipitated powder and N doping in nitrate medium precipitated powder has been occurred and the presence of S or N containing impurities on the grain boundaries have been improved light absorption of TiO2 significantly. However, these powders have exhibited low surface reactivities. The highest surface reactivity has been obtained with the powder precipitated in organic medium which also has the highest crystallite sizes (76 nm rutile and 34 nm anatase crystallites) with relatively low rutile weight percentage (10.0%). The surface-normalized rate constants of this powder are 0.02038 min-1.m-2 in real textile wastewater degradation and 0.0161 min-1.m-2 in methyl orange degradation, which are 0.01563 and 0.0091 min-1.m-2, respectively, for Degussa P25. Results have shown that this powder show 30-70% higher surface reactivities compared to Degussa P25. The main structural difference of organic medium precipitated powder and Degussa P25 has been found to be the anatase-rutile weight ratio and crystallite size of rutile phase whereas band gap energy of Degussa P25 is lower and other properties are not significantly different.Article Citation - WoS: 10Citation - Scopus: 12Enhanced Model Protein Adsorption of Nanoparticulate Hydroxyapatite Thin Films on Silk Sericin and Fibroin Surfaces(Springer, 2022) Özcan, Selçuk; Çiftçioğlu, MuhsinHydroxyapatite coated metallic implants favorably combine the required biocompatibility with the mechanical properties. As an alternative to the industrial coating method of plasma spraying with inherently potential deleterious effects, sol-gel methods have attracted much attention. In this study, the effects of intermediate silk fibroin and silk sericin layers on the protein adsorption capacity of hydroxyapatite films formed by a particulate sol-gel method were determined experimentally. The preparation of the layered silk protein/hydroxyapatite structures on glass substrates, and the effects of the underlying silk proteins on the topography of the hydroxyapatite coatings were described. The topography of the hydroxyapatite layer fabricated on the silk sericin was such that the hydroxyapatite particles were oriented forming an oriented crystalline surface. The model protein (bovine serum albumin) adsorption increased to 2.62 µg/cm2 on the latter surface as compared to 1.37 µg/cm2 of hydroxyapatite on glass without an intermediate silk sericin layer. [Figure not available: see fulltext.].Article Citation - WoS: 10Citation - Scopus: 9Bi̇yomalzemelerden İ̇zole Edi̇len Staphylococcus Epidermidis Suşlarinin Yüzey Özelli̇kleri̇ni̇n Beli̇rlenmesi̇(Ankara Mikrobiyoloji Derneği, 2010) Sudağıdan, Mert; Erdem, İlker; Çavuşoğlu, Cengiz; Çiftçioğlu, MuhsinThe surface properties of bacteria play an important role on adhesion to the biomaterial surface. In this study, the surface properties of Staphylococcus epidermidis strains isolated from clinically used polymeric biomaterial surfaces were investigated on the basis of zeta potential, hydrophobicity and surface topography. A total of 10 S.epidermidis strains isolated from intravenous catheters (n= 5), endotracheal tubes (n= 3) and central venous catheters (n= 2) which were used in the patients of pulmonary Intensive Care Unit, Ege University Medical Faculty Hospital, were included to the study. Seven of those isolates were biofilm producers, inhabiting biofilm genes, 2 were non-biofilm producers, however, inhabiting biofilm genes, and 1 was non-biofilm producer, inhabiting no biofilm genes. Zeta potential analysis have been performed in 3 different buffers (phosphate-buffered saline, 1 mM potassium chloride and 1 mM potassium phosphate buffer) and at different pH values (pH 4.1-8.2), in order to simulate in vivo environment of the biomaterials. Hydrophobicities of the strains were examined by bacterial adhesion to hydrocarbon (BATH) test and the surface topography of biofilms and slime layers were visualized by atomic force microscopy (AFM) and scanning electron microscopy (SEM) methods. It was found that all strains have negative zeta potential values (surface charge) in all buffers and pH values. In hydrophobicity analysis, the highest value (86%) was determined for non-biofilm forming S.epidermidis strain YT-169b (endotracheal tube isolate) and the lowest hydrophobicity (2.5%) was determined for biofilm forming S.epidermidis strain YT-212 (central venous catheter isolate). Biofilm and slime layers of the strains were imaginated by AFM and SEM analysis in ?m scale. SEM analysis showed that bacteria highly adhered to rough surfaces on biomaterial surfaces and the produced slime layers covered the surface of bacteria. In conclusion, elucidating the surface properties of opportunistic pathogens in different physiologic buffers will give important clues for the production of non-adhesive materials and antibacterial surfaces for those bacteria. It was also estimated that designing the surface of the biomaterial to have negative surface charge in the body and to be as smooth as possible will hamper biofilm formation.Article Citation - WoS: 6Citation - Scopus: 8The Effect of Powder Preparation Method on the Artificial Photosynthesis Activities of Neodymium Doped Titania Powders(Elsevier, 2018) Yurtsever, Hüsnü Arda; Çiftçioğlu, MuhsinThe effects of nanostructure on the artificial photosynthesis activities of undoped and Nd doped titania (TiO2) powders prepared by three different chemical co-precipitation methods were investigated. Substitutional/interstitial N and S doping was observed in powders due to the presence of high concentrations of HNO3 (NP) and H2SO4 (SP) in the powder preparation media, respectively. Nd, N and S doping caused anatase/rutile phase transformation inhibition and crystallite size reduction in the nanostructure. Light absorption was significantly enhanced by Nd doping and the residual SO42-/NOx species in the nanostructure. Photocatalytic hydrogen production activity of Nd doped NP powder was 4 times greater than undoped NP powder at 700 degrees C and had a high purity (CO:H-2 ratio similar to 0.00). CO was determined to be the main product in photocatalytic CO2 reduction. NP powders had the highest CO yields and Nd doping enhanced CO production. The powders with high crystallite sizes and rutile weight fractions had the highest artificial photosynthesis activities. (C) 2018 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.Article Citation - WoS: 4Citation - Scopus: 3Modification of Surface Charge Characteristics for Unsupported Nanostructured Titania-Zirconia Uf/Nf Membrane Top Layers With Calcination Temperature(Springer, 2020) Erdem, İlker; Çiftçioğlu, MuhsinCeramic membranes are more advantageous alternatives especially for harsh working conditions when compared with the polymeric membranes. The porous multilayer structure of the ceramic membranes (composed of support, intermediate, and top layers) can be prepared via different oxides. Titania and zirconia, having superior properties, are mainly preferred for the top layer formation. The separation properties of the membrane are both dependent on pore morphology and surface charge of the oxide(s) forming the top layer. The effect of surface charge in separation may be very significant in case of filtration of charged species with relatively lower mass as in the ultrafiltration (UF) and nanofiltration (NF). In this study, unsupported membrane top layers were prepared with varying titania/zirconia ratios by sol-gel technique. Their surface charges at different pH conditions after calcination at varying temperatures (400 degrees, 500 degrees, and 600 degrees C) were determined. The surface charge of the pure titania (full Ti) top layer was decreasing with the increasing calcination temperature. The highest magnitudes of zeta potential for both acidic and basic conditions were measured via Zr rich top layer (TiZr2575) at calcination temperatures >= 500 degrees C, which was composed of anatase, rutile (titania), and tetragonal (zirconia) phases after calcination. The tailor-made top layer can be prepared with modifications during membrane preparation.Article Citation - WoS: 48Citation - Scopus: 49The Effect of Rare Earth Element Doping on the Microstructural Evolution of Sol-Gel Titania Powders(Elsevier Ltd., 2017) Yurtsever, Hüsnü Arda; Çiftçioğlu, MuhsinThe development of a better understanding of the low temperature nanophase evolution of high surface area titania (TiO2) based powders is essential for their use in photocatalytic applications. A series of rare earth (RE) element doped TiO2 powders were prepared by sol-gel processing. The effects of RE doping level, ionic size and heat treatment temperature on the nanophase structure evolution and the dopant ion location in TiO2 main matrix were investigated. Anatase was determined to be the main phase up to 900 °C at all doping levels for all REs. Anatase to rutile phase transformation was inhibited by RE doping. The inhibitory effect of REs increased with increasing ionic radius. Oxide phases of La, Nd, Pr, Sm were not present up to 5% and Nd4Ti9O24 phase was formed at 10% doping level at 800 °C. The formation of RE2Ti2O7 phases were determined for the REs with relatively lower ionic radii at 800 °C.Article Citation - WoS: 19Citation - Scopus: 17Preparation and Characterization of Nanocrystalline Titania Powders by Sonochemical Synthesis(Elsevier Ltd., 2012) Çağlar Duvarcı, Özlem; Çiftçioğlu, MuhsinNanocrystalline mesoporous titania powders were synthesized by hydrolyzing titanium isopropoxide in ethanol-water mixtures which were ultrasonically treated without using any templates or chemicals. Titanium isopropoxide-ethanol mixture was added dropwise to a water-ethanol mixture placed in an ultrasonic bath. The properties of the sonochemically synthesized powder were compared with those of the powders prepared without ultrasonic treatment along with Degussa P-25 titania powder. The phase structure, crystallite size, surface area, particle size, powder density were determined and sintering behavior was analyzed in this work. The nanotitania powder prepared during ultrasonic induced hydrolysis (TiO 2-U) was determined to be formed from a mixture of anatase and brookite phases at 25°C. The brookite phase in nanotitania powder prepared without ultrasonic treatment (TiO 2-NoU) was detected at 70°C. The anatase-rutile phase transformation was completed in the 500-700°C range for both powders. The average crystallite sizes of the powders at 25°C were determined as 10 and 5nm for TiO 2-NoU and TiO 2-U, respectively. The surface area decreased from 238 to106m 2/g for TiO 2-NoU and from 287 to 82m 2/g for TiO 2-U when the calcination temperature was increased from 200 to 500°C. The evolution of the N 2 adsorption-desorption behavior with calcination temperature and the corresponding pore size distributions/volumes was attributed to the formation of closely packed submicron aggregates during powder synthesis and calcination. The sintering behavior was concluded to be controlled by 7-10nm crystallites and the submicron aggregates. The determination of the densification behavior of titania powders prepared by different methods with various levels of dopants may prove to be very useful for a better understanding of the phase/pore structure evolution which is crucial for a significant number of applications.Article Citation - WoS: 13Citation - Scopus: 14Monetite Promoting Effect of Citric Acid on Brushite Cement Setting Kinetics(Maney Publishing, 2014) Şahin, Erdem; Çiftçioğlu, MuhsinBrushite forming calcium phosphate cements receive growing interest in hard tissue scaffold applications due to their high surface area and high bioresorbability. The finer microstructure of monetite, the dehydrated form of brushite, has attracted attention for bone tissue engineering applications. The reduction in brushite content of the b-tricalcium phosphate-monocalcium phosphate monohydrate cement system by selective inhibition of growth upon addition of citric acid to excess setting liquid was investigated. The relaxation period during cement setting was monitored by pH stat titration and free drift runs. Spectrometric analysis revealed that the change in solubility of calcium phosphates upon addition of citric acid caused the inhibition of brushite formation and promotion of monetite precipitation. Dissolution of monetite crystals was insensitive to citrate adsorption despite their lower surface area compared to brushite. Overall brushite/ monetite ratio decreased consistently with increasing citric acid concentration in the of 0?1-0?5M range.