WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7150
Browse
13 results
Search Results
Now showing 1 - 10 of 13
Article Citation - WoS: 17Citation - Scopus: 23Synthesis of Zinc Borate by Inverse Emulsion Technique for Lubrication(Springer Verlag, 2011) Atakul Savrık, Sevdiye; Balköse, Devrim; Ülkü, SemraLubricating oil additives based on boron compounds are promising materials for lubrication due to their tribological advantages such as antiwear efficiency, good film strength, and high temperature resistance. This article deals with the preparation of zinc borate particles that are well dispersed and colloidally stabilized in mineral oil. This method starts with preparing two inverse emulsions (water-in-oil) with sorbitan monostearate (Span 60) as a surfactant, light neutral oil as a continuous phase, and the aqueous solutions of borax decahydrate (Na2B4O7·10H 2O) and zinc nitrate (Zn(NO3)2·6H 2O) as the dispersed phases. The produced particles were zinc borate crystals having both rod-like and spherical morphologies, and the diameters of spherical particles were changing between 20 and 30 nm. FTIR spectra of the obtained particles showed the characteristic peaks of trihedral borate (B(3)-O) and tetrahedral borate (B(4)-O) groups as well as the specific peaks of the sorbitan monostearate. TG showed 30.42% and 22.08% mass loss at 600 °C for the samples prepared by inverse emulsion and precipitation techniques, respectively. The endothermic peak at 50 °C is observed due to the melting of sorbitan monostearate and the heat of melting is evaluated as -3.50 J/g. Tribological studies revealed that sorbitan monostearate not only outperformed as a dispersing agent of inorganic particles, but also it proved to be an anti-wear agent. Zinc borate produced by precipitation decreased the wear scar diameter from 1.402 to 0.639 mm and the friction coefficient from 0.099 to 0.064. The inverse emulsion was effective in decreasing wear scar diameter and the friction coefficient by lowering them to 0.596 and 0.089 mm, respectively.Conference Object Citation - WoS: 23Citation - Scopus: 30Thermal Behaviour of Metal Soaps From Biodegradable Rubber Seed Oil(Springer Verlag, 2010) Balköse, Devrim; Egbuchunam, Theresa Obuajulu; Okieimen, Felix EbhodagheSoaps are a class of surface active compounds derived from natural oils and fats. Double decomposition reactions permit the synthesis of metallic soaps, which are long-chain carboxylates of metal ions, from alkaline ones such as sodium, potassium or ammonium soaps. Metallic soaps are commercially important as they find use in diverse applications such as driers in paints or inks, components of lubricating greases, heat stabilizers for plastics (especially PVC), catalysts and water proofing agents, fuel additives and cosmetic products amongst others. Many of these applications are related to the thermal properties of these compounds and the thermal behaviour of metal soaps in terms of decomposition processes is of great importance. Rubber seed oil (RSO) which is an unsaturated triglyceride abundantly available in Nigeria, India and Australia is an excellent starting material for metal soaps. In this study rubber seed oil having 2.2% myristic acid, 7.6% palmitic acid, 10.7% stearic acid, 20.61% oleic acid, 36.62% linoleic acid, 22.5% linolenic acid was used in making barium, calcium, cadmium and zinc soaps. The thermal behaviour of soaps (Ba, Ca, Cd and Zn) of rubber seed oil for use as additives in the processing of poly(vinyl chloride) (PVC) was investigated by thermal gravimetry and differential scanning calorimetry. The stability of the soaps was examined by thermogravimetry up to 873 K at a constant heating rate of 10 °C min -1. The soaps were found to be thermally stable up to 473 K as they recorded less than 5% mass loss at this temperature with values of apparent activation energy for decomposition varying from 52 to 96 kJ mol-1. Differential scanning calorimetric studies of the soaps revealed melting and decomposition behaviour of metal soaps. © 2010 Akadémiai Kiadó, Budapest, Hungary.Conference Object Citation - WoS: 22Citation - Scopus: 24Characterization of Poly(vinyl Chloride) Powder Produced by Emulsion Polymerization(Springer Verlag, 2010) Atakul Savrık, Sevdiye; Balköse, Devrim; Ulutan, Sevgi; Ülkü, SemraThe effect of emulsion process formulation ingredients on the morphology, structure, and properties of polyvinyl chloride (PVC) powder has been considered in this study. PVC powder was extracted with ethanol and films were obtained by solvent casting from tetrahydrofurane. Characterization of powders, films, and ethanol extract was performed through FTIR spectroscopy, DSC, AFM, SEM, EDX analysis, methylene blue, and nitrogen adsorption. PVC powder was composed of spheres of a large particle size range from 10 nm to 20 μm as shown by SEM. The specific surface area of the PVC powder was determined as 16 and 12 m 2 g-1 from methylene blue adsorption at 25 °C and from N2 adsorption at -196 °C, respectively. AFM indicated the surface roughness of the films obtained by pressing the particles was 25.9 nm. Density of PVC powder was determined by helium pycnometry as 1.39 g cm -3. FTIR spectroscopy indicated that it contained carbonyl and carboxylate groups belonging to additives such as surface active agents, plasticizers, and antioxidants used in production of PVC. These additives were 1.6% in mass of PVC as determined by ethanol extraction. EDX analysis showed PVC particles surfaces were coated with carbon-rich materials. The coatings had plasticizer effect since, glass transition temperature was lower than 25 °C for PVC powder and it was 80 °C for ethanol extracted powders as found by using differential scanning calorimetry. These additives from polymerization process made PVC powder more thermally stable as understood from Metrom PVC thermomat tests as well. © 2010 Akadémiai Kiadó, Budapest, Hungary.Article Citation - WoS: 11Citation - Scopus: 13Sorption and Diffusion of Water Vapour on Edible Films(Springer Verlag, 2008) Berkün, Didem; Balköse, Devrim; Tıhmınlıoğlu, Funda; Alsoy Altınkaya, SacideTwo types of films consisting of sodium salt of carboxymethyl cellulose (NaCMC) and hydroxypropyl cellulose (HPC) as film forming materials and glycerin as plasticizer were prepared, characterized and their water vapour sorption properties were determined. The water sorption isotherms of the films were measured using a magnetic suspension balance. Results show that diffusion of water vapour in NaCMC based film is faster than that in HPC based films, due to the heterogeneous structure and larger pore dimensions of the NaCMC films.Article Citation - WoS: 22Citation - Scopus: 28The Effect of Zinc Stearate on Thermal Degradation of Paraffin Wax(Springer Verlag, 2008) Gönen, Mehmet; Balköse, Devrim; İnal, Fikret; Ülkü, SemraIn this research, the effects of zinc stearate addition on paraffin wax degradation were investigated by differential scanning calorimetry (DSC) and thermogravimetry (TG). The apparent activation energies of wax decomposition in nitrogen and air atmospheres were determined as 76 and 37 kJ mol-1, respectively applying Kissinger method to TG data. The degradation rate constants of paraffin containing zinc stearate (0.1-0.5%) were found to be almost two times greater than that of paraffin only in air atmosphere. However, zinc stearate did not affect the rate constants in nitrogen significantly.Article Citation - Scopus: 1On the Terms Mass and Weight(Springer Verlag, 2008) Robens, E.; Klobes, P.; Balköse, Devrim; Amarasiri, S.; Jayaweera, A.A short survey is given on mass units and recommendations on the proper use of the notations mass and weight.Whereas mass is an inertial physical quantity in classical mechanics, weight is a force due to the gravitational field and depending on the geographic situation.Article Citation - WoS: 7Citation - Scopus: 7Water vapour adsorption on DNA(Springer Verlag, 2008) Balköse, Devrim; Alp, Burcu; Ülkü, SemraDNA adsorbed very low amount of water at low relative humidities, amount of adsorption increased to 140% at 98% relative humidity at 25°C. Heat of adsorption was 109 kJ mol-1 H2O for the increase of moisture content from 0 to 1.96%. At higher moisture contents the heat released approached heat of condensation of water vapour on free liquid surface, 40 kJ mol-1 H2O.Article Citation - WoS: 29Citation - Scopus: 31Cure Kinetics of Epoxy Resin-Natural Zeolite Composites(Springer Verlag, 2008) Cansever Erdoğan, Beyhan; Seyhan, Abdullah Tuğrul; Ocak, Yılmaz; Tanoğlu, Metin; Balköse, Devrim; Ülkü, SemraThe cure kinetics of epoxy resin and epoxy resin containing 10 mass% of natural zeolite were investigated using differential scanning calorimetry (DSC). The conformity of the cure kinetic data of epoxy and epoxy-zeolite system was checked with the auto-catalytic cure rate model. The results indicated that the hydroxyl group on the zeolite surface played a significant role in the autocatalytic reaction mechanism. This group was able to form a new transition state between anhydride hardener and epoxide group. The natural zeolite particles acted as catalyst for the epoxy system by promoting its curing rate.Article Citation - WoS: 9Citation - Scopus: 10Methods of Humidity Determination Part Ii: Determination of Material Humidity(Springer Verlag, 2008) Rübner, Katrin; Balköse, Devrim; Robens, E.Part II covers the most common methods of measuring the humidity of solid material. State of water near solid surfaces, gravimetric measurement of material humidity, measurement of water sorption isotherms, chemical methods for determination of water content, measurement of material humidity via the gas phase, standardisation, cosmonautical observations are reviewed.Article Citation - WoS: 8Citation - Scopus: 8Methods of Humidity Determination Part I: Hygrometry(Springer Verlag, 2008) Rübner, Katrin; Balköse, Devrim; Robens, E.Part I of the short survey covers definitions of air humidity and the respective measuring methods such as hygrometry, psychrometry, dew point measurement, LIDAR hygrometry and humidity sensors. Techniques based on property changes of matter with adsorbed moisture from air are reviewed.