WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7150
Browse
29 results
Search Results
Now showing 1 - 10 of 29
Article Effects of Span 60 Template and Freeze Drying on Zinc Borate Produced From Zinc Nitrate Hexahydrate and Borax Decahydrate(Taylor and Francis Ltd., 2022) Alp, Burcu; Gönen, Mehmet; Atakul Savrık, Sevdiye; Balköse, DevrimZinc borate is an important additive to polymers and lubricants. The process variables such as reactant concentration, presence of template in precipitating medium and drying method determine the composition and particle size of zinc borates. In the present study, zinc borate precipitate obtained by mixing aqueous zinc nitrate and borax decahydrate solutions was dried either by conventional method or by freeze drying. The products were well characterized by advanced methods. Zinc borate from 1 mol dm(-3) reactants had (2.1 +/- 0.5)x(2.5 +/- 0.5)x(1.3 +/- 0.2) mu m and (0.5 +/- 0.1)x(1.3 +/- 0.1)x(0.028 +/- 0.01) mu m dimensions by conventional and freeze drying respectively. Individual particles smaller in size is obtained since the particles are not agglomerated due to absence of surface tension of liquid water for case of freeze drying. Planar particles agglomerated into 20 to 60 mu m crystals in the presence of template Span 60 in 1 mol dm(-3) reactants for conventional drying. Nano zinc borate particles with primary particle size of (46 +/- 9) nm were obtained by decreasing the reactant concentration to 0.1 mol dm(-3). The primary particle size was decreased to (40 +/- 3) nm by addition of Span 60 to dilute solutions. However zinc borate nanoparticles obtained from dilute solutions adhered to each other forming agglomerates during conventional drying. Their freeze drying would allow formation of a freely flowing nano powder.Article Citation - WoS: 5Citation - Scopus: 6Use, Preparation, and Characterization of Copper-Containing Silica Gel(American Chemical Society, 2020) Ulutan, Sevgi; Tüzüm Demir, Ayşe Pınar; Balköse, DevrimThe preparation and characterization of humidity-indicating silica gel containing copper sulfate were aimed at in the present study. The equilibrium and kinetics of Cu(II) sorption were investigated by contacting 200-1600 mg dm(-3) Cu ion-containing solutions with silica hydrogel slabs having 10% silica. The diffusion coefficient of Cu(II) in silica hydrogel was determined to be on the order of 10(-10) m(2) s(-1). X-ray diffraction indicated that the gels contained mainly CuSO4 center dot 3H(2)O, CuSO4 center dot H2O, and small amounts of CuSO4 and CuSiO3 center dot 2H(2)O. The silica gel with Cu(II) can be used as a humidity indicator since its color changes from light blue to dark blue upon moisture adsorption.Article Citation - WoS: 6Citation - Scopus: 9Preparation and Characterization of Flexible Polyvinylchloride-Copper Composite Films(Smithers Rapra Technology, 2013) Kurt, Emrah; Özçelik, Cenk Yağız; Yetgin, Senem; Özmıhçı Ömürlü, Filiz; Balköse, DevrimFlexible PVC films are statically charged due to their low electrical conductivity. This creates fire threat during its handling. Conductive materials are added to films to prevent this. In the present study it was aimed to prepare PVC- copper composite films by sol gel technique and characterize the prepared films. It was aimed to increase the electrical conductivity of the films by adding copper powder. However, the copper particles settled down to bottom instead of forming a conductive network that covers the whole cross section. Thus at the film crosssection a plastic upper phase and a copper rich lower phase were present. The film did not conduct electricity due to this uneven distribution. The minimum volumetric and surface resistivities of the films were at the order of 109 ohm-cm and 1010 ohm square respectively.Article Citation - WoS: 2Citation - Scopus: 10Water and Water Vapor Sorption Studies in Poly(propylene)-Zeolite Composites(John Wiley and Sons Inc., 2003) Pehlivan, Hilal; Özmıhçı, Filiz; Tıhmınlıoğlu, Funda; Balköse, Devrim; Ülkü, SemraWater and water vapor sorption to porous poly(propylene)zeolite composites prepared by hot pressing have been studied as a function of zeolite loading. This work presents the first report on the effect of the zeolite as a filler on the water sorption properties of PP composites. Water swelling experiments were conducted at 25°C using pure PP and PP-zeolite film samples having different zeolite loadings (6-40 wt%). Since PP is a hydrophobic polymer, it does not sorp any water, but the composites having 10, 20, 30, and 40% zeolite sorbed 0.63, 1.00, 1.72 and 3.74 wt% water, respectively. The zeolite itself at the same conditions sorbed 24.5 wt% water. As the filler loading in the composites increased, equilibrium uptake values increased too. On the other hand, water vapor sorption and kinetics has been studied using a Cahn 2000 gravimetric sorption system. Within in the range 0.35-0.95%, water vapor was adsorbed by the composites containing 10-40 wt% zeolite. Experimental effective water vapor diffusivities of the composite films were about one order of magnitude higher than the experimental water diffusion coefficient in composites. The transport of water in composites was slower than that in the liquid water due to the longer diffusion pathway and adsorption on the surface of the composites. Although the liquid water may fill all the voids in the composite, water vapor is adsorbed on the surface of the zeolite only.Article Citation - WoS: 2Citation - Scopus: 2Morphology of Sodium Salt of Calf Thymus Dna on Mica, Alumina, and Silica Surfaces: Effect of Solvent and Drying Method(Taylor and Francis Ltd., 2017) Yetgin, Senem; Balköse, DevrimInvestigation of morphology of deoxyribonucleotide triphosphate (DNA) dried on different surfaces by atomic force microscopy (AFM) is important in DNA research that is focused on subjects of condensation for gene therapy, sizing, DNA mapping, and cancer examination. The solvent, the surface type, and the method of drying effect the morphology of DNA on solid surfaces. Ethanol and water were used as solvents, flat mica, silica, and alumina surfaces were used as the substrates in the present study. Different methods such as ambient air-drying, N2-forced flow regime drying, and freeze-drying have been applied to droplets of DNA solutions in water or ethanol on the substrates. Forced flow drying regime causes nonlinear DNA attachment on the surface and self-assembly. DNA vertical distance on mica surface was found to be 6 and 1.4 nm for DNA dried in ambient air from ethanol and water solutions, respectively. It was 1.6 nm for N2 flow drying of aqueous DNA solution on mica surface. It was 4.6, 4.6, and 1.99 nm for ambient, N2 flow, and freeze-dried aqueous DNA on alumina surfaces, respectively. Aqueous solution of DNA dried under N2 flow on silica surface had 0.8 nm vertical distance. The smallest standard deviation of 0.05 nm was observed for DNA dried under N2 flow on alumina surface.Article Citation - WoS: 15Citation - Scopus: 18Preparation and Characterization of Magnesium Stearate, Cobalt Stearate, and Copper Stearate and Their Effects on Poly(vinyl Chloride) Dehydrochlorination(John Wiley and Sons Inc., 2015) Gönen, Mehmet; Egbuchunam, Theresa Obuajulu; Balköse, Devrim; İnal, Fikret; Ülkü, SemraPreparation and characterization of pure metal soaps and investigation of their effects on poly(vinyl chloride) (PVC) dehydrochlorination were the objectives of the present study. Magnesium stearate (MgSt2), cobalt stearate (CoSt2), and copper stearate (CuSt2) were prepared by a precipitation method. An aqueous sodium stearate (NaSt) solution was mixed at 500 rpm with respective metal salt solutions at 75oC. The precipitates that formed were collected by filtration, washed with water, and ultimately dried at 105oC under reduced pressure. Lamellar crystals that melted on heating were obtained. Solid-liquid phase transitions were observed by optical microscopy at 160oC, 159oC, and 117oC for MgSt2, CoSt2, and CuSt2, respectively. However, the melting points of MgSt2, CoSt2, and CuSt2 were determined as 115oC, 159oC, and 111oC, respectively, by analysis by differential scanning calorimetry. The onset temperature of the mass loss was the lowest at 255oC for CuSt2 and the lowest activation energy for thermal decomposition was 18 kJ/mol for CuSt2. CoSt2 was effective in extending the induction time of PVC dehydrochlorination at both 140oC and 160oC. The activation energy calculated from stability time decreased from 175 kJ/mol for a blank PVC sample to 114, 105, and 107 kJ/mol for MgSt2, CoSt2, and CuSt2-containing PVC samples, respectively. All three metal soaps accelerated the dehydrochlorination of PVC. J. VINYL ADDIT. TECHNOL., 21:235-244, 2015.Article Citation - WoS: 5Citation - Scopus: 5Methylene Blue Adsorption From Aqueous Solutions To Flexible Poly(vinyl Chloride) Silica Composites(John Wiley and Sons Inc., 2015) Yetgin, Senem; Ulutan, Sevgi; Balköse, DevrimMethylene blue (MB) adsorption studies were performed with poly(vinyl chloride)-(dioctyl phthalate)-silica composites, which were obtained by using plastisol-plastigel technology. The films were flexible, having elastic modulus of 1.0-1.5 GPa. Diminishing MB concentration in the aqueous phase was followed as the adsorption process advanced by using visible spectroscopy. Contributions of the individual components of the composites to adsorption were also investigated. Although the MB adsorption capacity was extensively high for silica, it was moderate for the composite, most likely owing to the occlusion of pores of silica by plasticizer to some extent. The improvement of MB adsorption capacity of the composites as the silica ratio increased was explicitly deduced from the optical microscopy photographs. The diffusion coefficients of MB through the composites were 5 × 10-13, 6 × 10-13, and 3 × 10-13 m2 s-1 with regression coefficients of 0.73, 0.89, and 0.88 for 0, 2, and 16% silica-containing composites, respectively. Because of the slow diffusion of MB in poly(vinyl chloride)-silica composites, using them as dynamic column adsorbent was not practical. However, these versatile plastics can be used as plastic labels, colored clothing, leather substitutes, antimicrobial medical devices, and laser printable surfaces.Article Citation - WoS: 6Citation - Scopus: 7Preparation and Characterization of Flexible Poly(vinyl Chloride) Foam Films(John Wiley and Sons Inc., 2012) Şahin, Erdem; Yaşar Mahlıçlı, Filiz; Yetgin, Senem; Balköse, DevrimIn this study, the effect of activator ZnO and heating time at 190°C on foaming, gelation, and dehydrochlorination of poly(vinyl chloride) (PVC) plastisol was investigated. For this purpose, a PVC plastisol was prepared by mixing PVC, dioctyl phthalate (DOP), azodicarbonamide (ADC), ZnO, and the heat stabilizers calcium stearate (CaSt 2) and zinc stearate(ZnSt 2). PVC plastisol films were heated for 3, 6, 12, and 24 min periods at 190°C to see the effect of heating time on the gelation and foaming processes of the PVC foam. The time of 12 min was determined to be optimum for the completion of gelation and foaming processes without thermal degradation of PVC. No foaming was observed under the same conditions for the samples without ZnO. ZnO had a significant catalytic effect on ADC decomposition, accelerating the foaming of the films. Average porosity measurement showed a consistent increase in porosity with heating time up to 76% and the average density decreased from 1.17 to 0.29 g/cm 3 on foaming. Tensile tests showed that the tensile strength and tensile strain both increased considerably up to 0.98 MPa and 207%, respectively, with heating time and the elastic modulus was seen to gradually decrease from 4.7 to 0.7 MPa with heating time. Films without ZnO had higher tensile strength since there were no pores. PVC thermomat tests showed that ZnO lowered the stability time of plastigel film with azodicarbonamide.Article Citation - WoS: 18Citation - Scopus: 21Crystallization Kinetics and Affecting Parameters on Polycaprolactone Composites With Inorganic and Organic Additives(John Wiley and Sons Inc., 2015) Cesur, Serap; Alp, Burcu; Küçükgöksel, Yelda; Kahraman, Tansel; Balköse, DevrimThe isothermal crystallization and mechanical behavior of biodegradable polycaprolactone (PCL) composites with organic (oleic acid and glycerol monooleate) and inorganic (zinc oxide, organoclay, and hydroxy apatite) additives used alone or simultaneously were investigated. The effect of all additives on the degree of crystallinity percentage (DOC%), isothermal crystallization kinetics parameters, and mechanical test results of PCL composites was studied. The PCL composite films were prepared by solvent casting by using dichloromethane as the solvent. The films were characterized by X-ray diffraction, differential scanning calorimetry (DSC), and tensile tests. DSC of the first melting and X-ray diffraction DOC% results (for composites by solvent casting) are compatible. The values by DSC of the second melting (for composites by extrusion method) are lower. Organoclay gives the highest crystallinity among the other inorganic additives used. Small amounts of inorganic additives act as a nucleating agent and increase the crystallinity; the higher amounts decrease. The organic additives act as the plasticizer. When used alone, it lowers the crystallinity, but when used with inorganic additives, it improves the dispersion of inorganic particles in the polymer matrix. The isothermal crystallization kinetics parameters by Avrami analysis showed that crystallization was controlled by nucleation and the crystals had spherical structure. The nucleation type changed between thermal and athermal nucleation. The Pukanzky model interaction parameter B indicated that the organic additives improved the dispersion of inorganic particles in the polymer matrix. Statistically significant, eight correlations (F>6) were obtained for the crystallinity, crystallization parameters, Young's modulus, and tensile strength as a function of concentration of additives.Article Citation - WoS: 1Citation - Scopus: 1Flexible Pvc-Silica Composites as an Adsorptive Material for Water Soluble Dyes(Smithers Rapra Technology, 2013) Ulutan, Sevgi; Yetgin, Senem; Balköse, DevrimMethylene Blue (MB) adsorption studies were performed on flexible Polyvinyl Chloride/Silica composites which were obtained by using plastisol-plastigel technology. Change of MB concentration in aqueous phase as the adsorption process advanced was followed by using visible spectroscopy. The diffusion of MB through the composites exhibited non-Fickian behavior with a diffusivity of 10-11 m2s-1. Making use of such PVC-silica composite sheets as column packing, the packing time will be reduced and the surface available for diffusion will be increased. © 2013 Smithers Rapra Technology.
- «
- 1 (current)
- 2
- 3
- »