WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7150
Browse
15 results
Search Results
Now showing 1 - 10 of 15
Article Citation - WoS: 1Citation - Scopus: 1Synthesis of Pristine Chitosan Foams with Enhanced Pore Structure, Surface Area, and Mechanical Strength for Tissue Engineering Applications(Iop Publishing Ltd, 2025) Polat, M.; Cropper, Chelsea; Ozdamar, A. B.; Polat, H.With its excellent biocompatibility, biodegradability, and antimicrobial activity, chitosan is a promising scaffold material for hard-tissue engineering. Yet, pristine chitosan foams typically lack the strength and porosity required for such use. Here we present a simple emulsion-templating approach to fabricate pristine chitosan foams with optimized strength and porosity. Sodium dodecyl sulfate (SDS), a widely used biocompatible anionic surfactant, was employed at trace levels to aid polymerization. The foams display a dual-scale pore morphology. Cavities of 150-300 mu m are separated by around 50 mu m thick chitosan walls containing large interconnecting openings. The walls are further populated with meso- and macropores of 50-500 nm. This architecture should support cell attachment and growth, facilitate proliferation, and enhance nutrient transport and metabolic exchange. The structure yields high surface area (up to 10 m2 g-1). Mechanically, the thick-walled cavities impart both elastic recovery and high compressive resistance (255 kPa at 40% strain from foams polymerized with 4% chitosan). A preliminary drug-release study using vancomycin confirmed excellent loading and sustained release.Article Citation - WoS: 1Citation - Scopus: 1Spiral-Shaped Dual-Port Microstrip Antenna for 5G/6G Applications With Wideband-To Transition Using Shape-Memory Alloy(Iop Publishing Ltd, 2025) Atac, Enes; Karatay, AnilWe propose a compact, thermally reconfigurable dual-port microstrip antenna featuring a spiral-shaped design and shape-memory alloy (SMA) that enable switching between wideband and narrowband operation for 5G/6G communication systems. The SMA's thermally induced shape-memory behavior allows reconfiguration in response to temperature changes without the need for electronic or optical control circuits, thus avoiding issues such as self-interference problem, high costs, regular maintenance requirements, and durability concerns. In the wideband mode, measured results show that Port 1 covers 4.7-10.5 GHz and Port 2 covers 4.5-8.3 GHz, which closely agrees with simulations. When the SMA is activated by heat, the antenna switches to the narrowband mode, where Port 1 operates at 7.6 and 9.5 GHz, and Port 2 operates at 8.9 GHz. A ground-plane isolation element ensures low coupling between the ports, with the envelope correlation coefficient remaining below 0.1 across all configurations. The antenna reaches a peak gain of 5.2 dBi and maintains consistent performance through repeated switching. By combining spiral-shaped geometry with a responsive smart material, this work presents a novel and efficient approach for designing reconfigurable dual-port antennas suitable for future wireless technologies.Article The Curvature Perturbation Generated by Thermal Fluctuations During Thermal Inflation(Iop Publishing Ltd, 2025) Bae, Jeong-Myeong; Mohammad, Hammam Raihan; Stewart, Ewan D.; Zoe, HeeseungDuring thermal inflation, the temperature determines the number of e-folds of expansion of the universe and so thermal fluctuations are magnified into curvature perturbations. We use classical thermodynamics to calculate the subhorizon thermal fluctuations and trace their evolution into superhorizon temperature perturbations. We convert the temperature perturbations into curvature perturbations using the delta N-formalism, or equivalently the junction condition of curvature perturbations at the end of thermal inflation, denoted by subscript c, and show that the late-time power spectrum is PR= 15 Hc 3 k3 4 pi 4 g & lowast;T 3 kc 3 . cArticle Citation - WoS: 2Citation - Scopus: 4Injectable Nanocomposite Hydrogels With Co-Delivery of Oxygen and Anticancer Drugs for Higher Cell Viability of Healthy Cells Than Cancer Cells Under Normoxic and Hypoxic Conditions(Iop Publishing Ltd, 2025) Kehr, Nermin SedaInjectable nanocomposite hydrogels (NC hydrogels) have the potential to be used for minimally invasive local drug delivery. In particular, pH-sensitive injectable NC hydrogels can be used in cancer treatment to deliver high doses of anticancer drugs to the target site in cancer tissue without damaging healthy tissue. Recent studies have shown that in addition to stimuli-responsive delivery of anticancer drugs to cancer cells, oxygen delivery to the hypoxic environment of cancer tissue can lead to advanced effects, as hypoxia and an acidic pH are common characteristics of cancer tissue. However, few studies have investigated the effects of simultaneous administration of oxygen (O2) and pH-dependent anticancer drugs via injectable NC hydrogels on the viability of healthy and cancer cells under normoxic and hypoxic conditions. In this context, we describe the synthesis of injectable NC hydrogels composed of pH-responsive nanomaterials carrying oxygen and anticancer drugs. Our system provides sustained O2 release and pH-responsive sustained release of anticancer drugs for 15 and 30 d, respectively. Moreover, O2 delivery and/or simultaneous delivery of O2 and anticancer drug resulted in higher cell survival of healthy fibroblast cells than malignant Colo-818 cells under hypoxic conditions (1% O2) after 7 d of incubation.Article Machinability Investigation on Cnc Milling of Recycled Short Carbon Fiber Reinforced Magnesium Matrix Composites(Iop Publishing Ltd, 2024) Atasoy, Sahin; Kandemir, SinanThis study investigates the machinability of magnesium matrix composites reinforced with short carbon fibers, which represent novel materials in the field. AZ91 alloy and its composites containing 2.5 and 5 wt% recycled carbon fiber (rCF) reinforcements were used as workpieces. Face milling was conducted using uncoated carbide cutting tools under dry cutting conditions with varied cutting speeds (480-560-640 m min(-1)) and feed rates (0.65-0.8-0.95 mm min(-1)). The experimental design was based on the Taguchi L-9 (3(3)) orthogonal array. Analysis included cutting forces, surface roughness, wear on cutting inserts, and chip morphology to assess machinability. Taguchi, analysis of variance, and regression methods were employed to analyze cutting force and surface roughness results. Findings indicated satisfactory machinability for AZ91 alloy and comparatively poorer performance for the 5 wt% rCF reinforced composite, with increased reinforcement content correlating with higher cutting force and surface roughness. SEM and EDX analyses revealed significant built-up layer formation on cutting inserts, with predominantly spiral-shaped continuous chips observed in the experiments. Overall, the study affirmed the machinability of the composites and identified suitable cutting parameters for further investigations.Review Citation - WoS: 1Citation - Scopus: 1Colloidal Quantum Dots as Solution-Based Nanomaterials for Infrared Technologies(Iop Publishing Ltd, 2024) Sevim Ünlütürk, S.; Taşcıoğlu, D.; Özçelik, S.This review focuses on recent progress of wet-chemistry-based synthesis methods for infrared (IR) colloidal quantum dots (CQD), semiconductor nanocrystals with a narrow energy bandgap that absorbs and/or emits IR photos covering from 0.7 to 25 micrometers. The sections of the review are colloidal synthesis, precursor reactivity, cation exchange, doping and de-doping, surface passivation and ligand exchange, intraband transitions, quenching and purification, and future directions. The colloidal synthesis section is organized based on precursors employed: toxic substances as mercury- and lead-based metals and non-toxic substances as indium- and silver-based metal precursors. CQDs are prepared by wet-chemical methods that offer advantages such as precise spectral tunability by adjusting particle size or particle composition, easy fabrication and integration of solution-based CQDs (as inks) with complementary metal-oxide-semiconductors, reduced cost of material manufacturing, and good performances of IR CQD-made optoelectronic devices for non-military applications. These advantages may allow facile and materials' cost-reduced device fabrications that make CQD based IR technologies accessible compared to optoelectronic devices utilizing epitaxially grown semiconductors. However, precursor libraries should be advanced to improve colloidal IR quantum dot synthesis, enabling CQD based IR technologies available to consumer electronics. As the attention of academia and industry to CQDs continue to proliferate, the progress of precursor chemistry for IR CQDs could be rapid. © 2024 IOP Publishing Ltd. All rights, including for text and data mining, AI training, and similar technologies, are reserved.Article Citation - Scopus: 1Genetic Algorithm Optimization of Langevin Thermostat and Thermal Properties of Graphene-Aluminum Nanocomposites: a Molecular Dynamics(Iop Publishing Ltd, 2024) Toprak, KasimThe thermal properties of a laminated structure of graphene-coated aluminum composite nanomaterial were investigated through non-equilibrium molecular dynamics (NEMD) simulations to address the problem of temperature deviation in the thermostat volume applied. This paper presents a new insight into the best values of timestep and Langevin thermostat damping parameters for each atom in the nanomaterial with different size configurations using the genetic algorithm (GA) method by considering the timestep and thermostat damping parameters for each atom type, as well as the thickness of the nanomaterial, the thermostat, buffer, and heat flow lengths. The initial population results indicate that the thermostat temperature deviation increases with higher thermostat damping coefficients and timestep. However, the deviation decreases significantly with increased heat flow and thermostat lengths. Variations in buffer length and aluminum thickness do not have a significant effect on temperature. The application of a GA for optimization leads to a decrease in thermostat temperature deviation. The optimized parameters resulted in better thermostat temperature deviations when analyzing the temperature, aluminum thickness, and both buffer and thermostat lengths. Additionally, the thermal conductivity of aluminum-graphene nanomaterial decreases with increasing temperature, buffer length, and aluminum thickness, but increases by up to 9.85% with increasing thermostat length.Article Citation - WoS: 3Citation - Scopus: 6Large-Area (50 Cm X 50 Cm) Optically Transparent Electromagnetic Interference (emi) Shielding of Zto/Ag an Analytical/Numerical and Experimental Study of Optoelectrical and Emi Shielding Properties(Iop Publishing Ltd, 2024) Astarlioglu, Aziz Taner; Oz, Yahya; Unal, Emre; Kilic, Nail Bugra; Celikli, Cenkay; Ozdemir, Mehtap; Erdogan, NursevTransparent conducting oxides (TCOs), exhibiting both high optical transparency and low electrical resistivity, are commonly employed in optoelectronic devices. However, acquiring a balance between these optical and electrical properties in a uniform way over large areas has been a pending challenge, which is essential to achieving optically transparent electromagnetic interference (EMI) shielding surfaces. In this study, we propose and demonstrate a stratified thin film structure consisting of zinc-doped tin oxide (Zn2SnO4, ZTO) as TCO along with a metal layer of silver (Ag) deposited on a large area of 50 cm x 50 cm polycarbonate (PC) substrate enabled by a scanning magnetron sputtering gun. We achieved high EMI shielding of 99.9% at the optical transparency of 68% in the visible spectrum by engineering the stratified architecture of ZTO/Ag/ZTO. The Ag layer of 18 nm in thickness with a sheet resistance of 10 Omega/sq yields shielding effectiveness (SE) of 27 dB in a wide frequency range of 2-20 GHz. The bottom and top ZTO layers, 20 and 40 nm thick, respectively, provide the lowest optical loss of 13% across 400-700 nm. The structure's EMI shielding, optical and structural performances were systematically characterized through a free-space focused-beam system, UV-Vis spectrophotometer, ellipsometry, focused ion-beam cross-sectional sampling and imaging, transmission electron microscopy, atomic force microscopy and secondary ion mass spectroscopy. EMI shielding and optical performances were validated by CST Microwave Studio and the transfer matrix method, respectively. These findings indicate that the proposed multi-layer architecture holds great promise for large-area EMI shielding and other optoelectronic applications.Article Citation - WoS: 14Citation - Scopus: 163D Bioprinting of mouse pre-osteoblasts and human MSCs using bioinks consisting of gelatin and decellularized bone particles(Iop Publishing Ltd, 2024) Kara, Aylin; Distler, Thomas; Akkineni, Ashwini Rahul; Tihminlioglu, Funda; Gelinsky, Michael; Boccaccini, Aldo R.One of the key challenges in biofabrication applications is to obtain bioinks that provide a balance between printability, shape fidelity, cell viability, and tissue maturation. Decellularization methods allow the extraction of natural extracellular matrix, preserving tissue-specific matrix proteins. However, the critical challenge in bone decellularization is to preserve both organic (collagen, proteoglycans) and inorganic components (hydroxyapatite) to maintain the natural composition and functionality of bone. Besides, there is a need to investigate the effects of decellularized bone (DB) particles as a tissue-based additive in bioink formulation to develop functional bioinks. Here we evaluated the effect of incorporating DB particles of different sizes (<= 45 and <= 100 mu m) and concentrations (1%, 5%, 10% (wt %)) into bioink formulations containing gelatin (GEL) and pre-osteoblasts (MC3T3-E1) or human mesenchymal stem cells (hTERT-MSCs). In addition, we propose a minimalistic bioink formulation using GEL, DB particles and cells with an easy preparation process resulting in a high cell viability. The printability properties of the inks were evaluated. Additionally, rheological properties were determined with shear thinning and thixotropy tests. The bioprinted constructs were cultured for 28 days. The viability, proliferation, and osteogenic differentiation capacity of cells were evaluated using biochemical assays and fluorescence microscopy. The incorporation of DB particles enhanced cell proliferation and osteogenic differentiation capacity which might be due to the natural collagen and hydroxyapatite content of DB particles. Alkaline phosphatase activity is increased significantly by using DB particles, notably, without an osteogenic induction of the cells. Moreover, fluorescence images display pronounced cell-material interaction and cell attachment inside the constructs. With these promising results, the present minimalistic bioink formulation is envisioned as a potential candidate for bone tissue engineering as a clinically translatable material with straightforward preparation and high cell activity.Article Citation - WoS: 3Citation - Scopus: 4Patient-Specific Finite Element Analysis for Assessing Hip Fracture Risk in Aging Populations(Iop Publishing Ltd, 2024) Chethan, K. N.; Waldschmidt, Nadine Schmidt Genannt; Corda, John Valerian; Shenoy, Satish B.; Shetty, Sawan; Keni, Laxmikant G.; Mihcin, SenayThe femur is one of the most important bone in the human body, as it supports the body's weight and helps with movement. The aging global population presents a significant challenge, leading to an increasing demand for artificial joints, particularly in knee and hip replacements, which are among the most prevalent surgical procedures worldwide. This study focuses on hip fractures, a common consequence of osteoporotic fractures in the elderly population. To accurately predict individual bone properties and assess fracture risk, patient-specific finite element models (FEM) were developed using CT data from healthy male individuals. The study employed ANSYS 2023 R2 software to estimate fracture loads under simulated single stance loading conditions, considering strain-based failure criteria. The FEM bone models underwent meticulous reconstruction, incorporating geometrical and mechanical properties crucial for fracture risk assessment. Results revealed an underestimation of the ultimate bearing capacity of bones, indicating potential fractures even during routine activities. The study explored variations in bone density, failure loads, and density/load ratios among different specimens, emphasizing the complexity of bone strength determination. Discussion of findings highlighted discrepancies between simulation results and previous studies, suggesting the need for optimization in modelling approaches. The strain-based yield criterion proved accurate in predicting fracture initiation but required adjustments for better load predictions. The study underscores the importance of refining density-elasticity relationships, investigating boundary conditions, and optimizing models through in vitro testing for enhanced clinical applicability in assessing hip fracture risk. In conclusion, this research contributes valuable insights into developing patient-specific FEM bone models for clinical hip fracture risk assessment, emphasizing the need for further refinement and optimization for accurate predictions and enhanced clinical utility.