WoS İndeksli Yayınlar Koleksiyonu / WoS Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7150
Browse
6 results
Search Results
Now showing 1 - 6 of 6
Article Citation - WoS: 24Citation - Scopus: 23Photovoltaic Performance of Magnetron Sputtered Antimony Selenide Thin Film Solar Cells Buffered by Cadmium Sulfide and Cadmium Sulfide /Zinc Sulfide(Elsevier B.V., 2023) Cantas, A.; Gundogan, S.H.; Turkoglu, F.; Koseoglu, H.; Aygun, G.; Ozyuzer, L.Antimony selenide (Sb2Se3)-based thin-film solar cells have recently attracted worldwide attention as an abundant, low-cost, and efficient photovoltaic technology. The highest efficiencies recorded for Sb2Se3 solar cells have been obtained using cadmium sulfide (CdS) as a buffer layer. The Cd-included hybrid buffer layers could be one option to increase device efficiency through more effective usage of light. Therefore, in this work, the effect of single CdS and hybrid CdS/zinc sulfide (ZnS) buffer layers on the photovoltaic performance of Sb2Se3 thin-film solar cells has been investigated in detail. Sb2Se3 thin films have been deposited on molybdenum (Mo)-coated soda-lime glass (SLG) substrates by radio frequency magnetron sputtering technique followed by a post-heat treatment process. The morphological, and structural properties of Sb2Se3 thin films have been investigated by X-Ray Diffraction and Scanning Electron Microscopy. To compare the device performances of single CdS and hybrid CdS/ZnS buffered Sb2Se3 thin-film solar cells, SLG/Mo/Sb2Se3/CdS/ZnS/indium tin oxide (ITO) and SLG/Mo/Sb2Se3/CdS/ITO structures have been fabricated. The findings of this study have revealed a reduction in solar cells’ performance from η=3.93% for CdS buffer to η=0.13% for CdS/ZnS hybrid buffer. The change in the solar cell performance using the CdS/ZnS hybrid buffer has been discussed in detail. © 2023 Elsevier B.V.Article Citation - WoS: 6Citation - Scopus: 5Structural and Optical Characteristics of Antimony Selenosulfide Thin Films Prepared by Two-Step Method(Springer, 2022) Türkoğlu, Fulya; Ekren, Memduh Emirhan; Cantaş, Ayten; Yakıncı, Kübra; Gündoğan, Hazal; Aygün, Gülnur; Özyüzer, LütfiAntimony triselenide (Sb2Se3) is one of the most promising absorber material choices among the inorganic semiconductors that has attracted much attention today. However, highest recorded efficiencies for Sb2Se3 solar cells are still lower than ideal. Exploring antimony selenosulfide (Sb-2(SxSe1-x)(3)) to increase device performance is one option because some features of alloyed Sb-2(SxSe1-x)(3) depend on composition such as bandgap and band position. In this study, two-step process was used to grow Sb-2(SxSe1-x)(3) thin films. In the first stage, Sb2Se3 thin films were deposited on soda lime glass substrates using direct current magnetron sputtering technique. In the second stage, Sb2Se3 thin films were exposed to sulfurization process in a quartz ampoule to obtain Sb-2(SxSe1-x)(3) thin films. Characterization results showed that morphological, optical, and structural properties of Sb-2(SxSe1-x)(3) thin films grown by presented method were highly dependent on amount of sulfur in the films. By the adjustment of the S/S + Se atomic ratio, Sb-2(SxSe1-x)(3) absorber materials with suitable bandgap, favorable orientation and compact morphology can be obtained for photovoltaic applications.Article Citation - WoS: 21Citation - Scopus: 24Effect of Defects and Secondary Phases in Cu2znsns4 Absorber Material on the Performance of Zn(o,s) Buffered Devices(Elsevier Ltd., 2019) Türkoğlu, Fulya; Köseoğlu, Hasan; Cantaş, Ayten; Akça, Fatime Gülşah; Meriç, Ece; Buldu, Dilara Gökçen; Aygün, GülnurCopper zinc fin sulfide (CZTS) absorber layer attracts so much attention in photovoltaic industry since it contains earth abundant, low cost and non-toxic elements contrary to other chalcogenide based solar cells. In the present work, CZTS absorber layers were prepared following a two-stage process: firstly, a stack of metal precursors (Copper (Cu)/Tin (Sn)/Zinc (Zn)/Copper (Cu)) were deposited on molybdenum (Mo) substrate by magnetron sputtering, then this stack was annealed under S atmosphere inside a tubular furnace. CZTS thin films were investigated using energy dispersive X-ray spectroscopy, X-ray diffraction, scanning electron microscopy and Raman spectroscopy. The effect of sulfurization time and the thickness of top and bottom Cu layer in precursors on the properties of CZTS thin films were investigated. The importance of Cu thickness adjacent to Sn to avoid detrimental phases was addressed. The significance of sulfurization time to restrict the Sn and Zn losses, formation of oxides such as fin dioxide and zinc oxide, and formation of molybdenum disulfide and voids between Mo/CZTS interface was also addressed. Moreover, cadmium sulfide buffer layer, which is conventionally used in CZTS solar cells, is replaced by an environmentally friendly alternative zinc oxysulfide buffer layer.Article Citation - WoS: 10Citation - Scopus: 10In-Situ Spectroscopic Ellipsometry and Structural Study of Hfo2 Thin Films Deposited by Radio Frequency Magnetron Sputtering(American Institute of Physics, 2014) Cantaş, Ayten; Özyüzer, Gülnur Aygün; Basa, Deepak KumarWe have investigated the reduction of unwanted interfacial SiO2 layer at HfO2/Si interface brought about by the deposition of thin Hf metal buffer layer on Si substrate prior to the deposition of HfO2 thin films for possible direct contact between HfO2 thin film and Si substrate, necessary for the future generation devices based on high-κ HfO2 gate dielectrics. Reactive rf magnetron sputtering system along with the attached in-situ spectroscopic ellipsometry (SE) was used to predeposit Hf metal buffer layer as well as to grow HfO2 thin films and also to undertake the in-situ characterization of the high-κ HfO2 thin films deposited on n-type 〈100〉 crystalline silicon substrate. The formation of the unwanted interfacial SiO2 layer and its reduction due to the predeposited Hf metal buffer layer as well as the depth profiling and also structure of HfO2 thin films were investigated by in-situ SE, Fourier Transform Infrared spectroscopy, and Grazing Incidence X-ray Diffraction. The study demonstrates that the predeposited Hf metal buffer layer has played a crucial role in eliminating the formation of unwanted interfacial layer and that the deposited high-κ HfO2 thin films are crystalline although they were deposited at room temperature.Article Citation - WoS: 10Citation - Scopus: 10Morphology, Order, Light Transmittance, and Water Vapor Permeability of Aluminum-Coated Polypropylene Zeolite Composite Films(John Wiley and Sons Inc., 2011) Balköse, Devrim; Oğuz, Kaan; Özyüzer, Lütfi; Tarı, Süleyman; Arkış, Esen; Özmıhçı Ömürlü, FilizIn this study, the polypropylene-zeolite composite films having 2-6 wt % natural zeolite were coated with a thin film of aluminum (Al) by magnetron sputtering, and the contribution of the Al coating on film properties was investigated. The samples were characterized by EDX, X-ray diffraction, SEM, AFM, UV-visible spectroscopy, and water vapor permeation analyses. The surface of the films coated with a smooth Al film having 98-131 nm thickness. EDX revealed that Al percentage on the surface appeared to be as 8-10 wt % indicating contribution of polymer surface under Al film to analysis. XRD analysis showed that the grain size of Al at the surface was 22-29 nm. The surface roughness increased after Al-coating process. The transmission of coated films was very low for both UV and visible regions of the light spectrum. Permeation analysis indicated that water vapor permeation was lower for Al-coated material.Conference Object Citation - WoS: 1Selection of the Best Proper Dc-Squids in a Multi-Squid Configuration(IEEE, 2007) Avcı, İlbeyi; Akram, R.; Bozbey, Ali; Tepe, Mustafa; Abukay, DoğanWe have carried out experimental investigation of multi-DC-SQUID magnetometer configuration fabricated on YBa2Cu30 7-δ thin films onto 24 degree SrTiO3 bicrystal substrates by directly coupling the pick-up loop to DC-SQUIDs. The layout of the magnetometer pick-up loop was chosen as a square washer configuration by maximizing loop effective area and minimizing loop inductance. We have used De-Magnetron Sputtering technique for deposition of the films and chemical etching process for patterning the Josephson junctions having 4 μm widths. The use of multi-SQUID configuration is related to the selection of the best proper junctions for SQUID to improve the chip sensitivity with selectivity option of choosing the squid junctions rather than multichannel operation. Selection of the best junctions compared to each other depending on the junction critical currents and noise levels caused by the fabrication process and placements of the junctions on the grain boundary enable having an increased output signal of the DC-SQUID.