TR Dizin İndeksli Yayınlar / TR Dizin Indexed Publications Collection

Permanent URI for this collectionhttps://hdl.handle.net/11147/7149

Browse

Filters

2007 - 200942010 - 201992020 - 20238

Settings

Department: search.filters.department.İzmir Institute of Technology. Chemical EngineeringLanguage: search.filters.language.en

Search Results

Now showing 1 - 10 of 21
  • Article
    Pomza ve Nsdd-pomza ile Sabit Yataklı Kolon Reaktörde Metilen Mavisi Giderimi: Deneysel ve Modelleme Çalışması
    (2019) Balcı, Esin; Ökten, Hatice Eser; Genişoğlu, Mesut; Recepoğlu, Yaşar Kemal; Gören, Ayşegül Yağmur
    Nano sıfır değerlikli demir (nSDD) yüksek renk konsantrasyonlarına sahip tekstil atıksularının arıtımında ekonomik ve çevre dostu bir adsorban olarak ortaya çıkmaktadır. Ancak nSDD partikülleri sulu çözeltilerde elektrostatik etkileşimler sebebiyle kolayca topaklaşmakta ve bu da arıtma veriminin düşmesine neden olmaktadır. Dolayısıyla düşük maliyetli, doğal poröz yapıda ve ortalama 2m2/gr spesifik yüzey alanına sahip pomza, nSDD topaklaşmasını önleyici bir malzeme olarak kullanılabilir. Bu çalışmada sadece pomza ve pomzanSDD (ağırlıkça 9:1) karışımının kullanıldığı kolon reaktörde 25, 50, 75 ve 100 mg/L metilen mavisi konsantrasyonları için arıtma verimleri incelenmiştir. Pomzanın ve pomza-nSDD karışımının 100 mg/L metilen mavisi deneyindeki toplam kapasiteleri sırasıyla 2,8 ve 4,2 mg/g-adsorban olarak bulunmuştur. Özellikle düşük konsantrasyonlarda, pomza-nSDD karışımının arıtma performansını önemli ölçüde arttırdığı görülmüştür. Thomas modeli deneysel verilere uygulanmış ve modelin öngörü gücünün düşük konsantrasyonda yüksekken, yüksek konsantrasyonlarda ortalama olduğu kanısına varılmıştır.
  • Article
    Citation - Scopus: 2
    A Comparative Assessment for Efficient Oleuropein Extraction From Olive Leaf (olea Europaea L. Folium)
    (Murat Yakar, 2023) Recepoğlu, Yaşar Kemal; Gümüşbulut, Gülin; Yüksel Özşen, Aslı
    Since oleuropein has long been known in the health sector and is abundant directly in our country as the fourth largest olive producer, oleuropein, the predominant phenolic ingredient in olive leaves, was recovered in this study using Soxhlet extraction. The effects of different solvent types (acetonitrile, ethanol, methanol, and water), extraction period (4 cycles, 4 h, and 8 h), particle size (250-500 µm and 900-2000 µm), and pretreatment of olive leaves on the yield of oleuropein were examined to determine the maximum yield. A greater oleuropein yield was obtained when the particle size of olive leaves utilized for extraction was lowered. Furthermore, aqueous solvents revealed a higher yield of oleuropein than pure solvents and prolonging the extraction duration resulted in a significant increase in the amount of oleuropein extracted. On the other hand, pretreatment of olive leaves resulted in a reduction in oleuropein output. As a result, with 36% extraction efficiency in terms of olive leaf conversion, the highest oleuropein extraction yield was obtained as 13.35 mg g-1 dry leaf for 8 h of extraction time using olive leaves with a particle size of 250-500 µm and an 80% methanol solution as solvent. © Author(s) 2023.
  • Research Project
    Nanolifli yapıda, sinir büyüme faktörü yüklü mikro küreleri içeren jalatin bazlı doku iskelelerinin hazırlanması ve karakterizasyonu
    (TÜBİTAK - Türkiye Bilimsel ve Teknolojik Araştırma Kurumu, 2014) Altınkaya, Sacide; Erdal, Esra; Büyüköz, Melda
    In living organisms most of the tissues have the capability of regeneration; on the other hand, this situation is different in mammalian adult neural cells since they loose their ability of proliferation. Compared to peripheral nervous system, central nervous system has restricted regeneration capability which results in trauma, stroke and neuropathology etc. The first studies for the regeneration of nervous system concentrated on the use of autographs, tissue transplanted from one part of the body to another in the same individual, but it has limitations including short-age. Another type of investigation was allograft, which is transplantation of cells isolated from cadavers to the patient, but this approach is also not suitable because of host immune rejection. A new hope to cure neurodegenerative diseases appeared with biomaterials and tissue engineering studies. In this study, it is aimed to develop a novel, nanofibrous scaffolds with the capability of controlled releasing neural growth factor loaded in microspheres. Nanofibrous and oriented scaffolds were prepared from gelatin by a combination of thermally induced phase separation (TIPS), porogen-leaching and molding techniques while alginate microspheres were produced in oil in water emulsion through cross linking of alginate with calcium ions. The bioactivity of the growth factor released from microspheres was determined using PC12 cell line, derived from rat adrenal medulla and differentiate when treated with nerve growth factor. The scaffolds including connected pores with a high porosity, nanofibrous structure which mimic the extracellular matrix and properties similar to natural brain tissure were produced. Compared to solid walled scaffolds, nanofibrous scaffolds allow attachment of cells without any change in their morphologies. Model protein Į-chemotripsin and bovin serum albumin used for protecting the activity of nerve growth factor were loaded in alginate microspheres with an encapsulation efficiency of 100 %. It was found that NGF loaded into microspheres can maintain its activity and it can even differentiate PC-12 cells in a shorter time compared to NGF directly added into cell culture medium.
  • Article
    Citation - WoS: 3
    Citation - Scopus: 4
    Photocatalytic Degradation of Aquatic Organic Pollutants With Zn- and Zr-Based Metalorganic Frameworks: Zif-8 and Uio-66
    (TÜBİTAK - Türkiye Bilimsel ve Teknolojik Araştırma Kurumu, 2022) Çalık, Fatma Defne; Erdoğan, Bilgesu; Yılmaz, Esra; Saygı, Gizem; Çakıcıoğlu-Özkan, Fehime
    Water treatment has been an essential issue with the increasing population over 40 years. Researchers center on the major organic pollutants, such as dyes, pesticides, and pharmaceutical products. Photocatalytic degradation is one of the promising methods for aquatic organic pollutant treatment. Over the years, scientists have been working on developments for photocatalysts to enhance their pollutant degradation performances. From the reviewed studies, it is seen that properties like surface area, chemical, mechanical, and thermal stability, and uniform distribution of active sites are crucial, and an increase in these properties provides better degradation efficiency. In this sense, metal-organic frameworks as photocatalysts can be considered more advantageous. This study focuses on the organic aquatic pollutant degradation studies by using well-known MOFs like ZIF-8 and UiO-66 photocatalysts. Mainly the organic dye (RhB, MB, MO, etc.) degradation efficiencies of ZIF-8 and UiO-66 have been achieved to 100%. Recently, the degradation capacities of various pharmaceuticals such as diazinon, acetaminophen, levofloxacin, and sulfamethoxazole have also been investigated. According to the reviewed studies, ZIF-8 and UiO-66 can be considered remarkable photocatalysts for the degradation of organic pollutants.
  • Article
    Citation - WoS: 4
    Citation - Scopus: 5
    Co2 Absorption Into Primary and Secondary Amine Aqueous Solutions With and Without Copper Ions in a Bubble Column
    (TÜBİTAK - Türkiye Bilimsel ve Teknolojik Araştırma Kurumu, 2022) Yousefzadeh, Hamed; Güler, Cansu; Erkey, Can; Uzunlar, Erdal
    Chemical absorption of CO2 into aqueous amine solutions using a nonstirred bubble column was experimentally investigated. The performance of CO2 absorption of four different primary and secondary amines including monoethanolamine (MEA), piperazine (PZ), 2-piperidineethanol (2PE), and homopiperazine (HPZ) were compared. The effects of initial concentration of amine, the inlet mole fraction of CO2, and solution temperature on the rate of CO2 absorption and CO2 loading (mol CO2/mol amine) were studied in the range of 0.02–1 M, 0.10–0.15, and 25–40 °C, respectively. The effect of the presence of copper ions in the amine solution on CO2 loading was also studied. By comparison of the breakthrough curves of the amines at different operational conditions, it was revealed that the shortest and longest time for the appearance of the breakthrough point was observed for MEA and HPZ solutions, respectively. CO2 loading of MEA, 2PE, PZ, and HPZ aqueous solutions at 25 °C, 0.2 M of initial concentration of amine, and 0.15 of inlet mole fraction of CO2 were 1.06, 1.14, 1.13, and 1.18 mol CO2/mol amine, respectively. By decreasing the inlet mole fraction of CO2 from 0.15 to 0.10, CO2 loading slightly decreased. As the initial concentration of amine and temperature decreased, CO2 loading increased. Also, the presence of copper ions in the absorbent solution resulted in a decrease in the CO2 loading of MEA and HPZ aqueous solutions. In case of PZ and 2PE amines, adding copper ions led to precipitation even at low copper ion concentrations.
  • Article
    Citation - WoS: 1
    Citation - Scopus: 1
    Selective Catalytic Hydrogenation of Cellulose Into Sorbitol With Ru-Based Catalysts
    (TÜBİTAK, 2022) Orak, Ceren; Sapmaz, Aycan; Yüksel, Aslı
    Sorbitol is one of the platform chemicals and can be produced from various renewable and sustainable sources via different processes. Hydrothermal liquefaction is an effective and promising approach to produce sorbitol, since the subcritical reaction media and appropriate catalysts provide a selective production of platform chemicals. In this study, sorbitol was produced from different renewable sources (cellulose and glucose) in the presence of Ru-based catalysts (Ru/SiO2, Ru/AC, Ru/SBA-15, and Ru/SBA-15-SO3) under subcritical conditions. The highest cellulose conversion was achieved as 90% in the presence of Ru/SBA-15-SO3 for 1 h of reaction duration. The highest sorbitol yield (%) by hydrothermal liquefaction of cellulose was obtained as 6.2% by using Ru/AC for 1 h of reaction duration. A total of 99.9% of glucose conversion was achieved in the presence of all catalysts. The highest sorbitol yield (%) by hydrothermal liquefaction of glucose was found as 3.8% for 1 h of reaction duration. Owing to the results of GC-MS analysis, the intermediate products were identified, and, thus, a reaction pathway was proposed.
  • Article
    Citation - WoS: 11
    Citation - Scopus: 13
    Effect of Cnt Incorporation on Pan/Ppy Nanofibers Synthesized by Electrospinning Method
    (TÜBİTAK, 2020) İnce Yardımcı, Atike; Tanoğlu, Metin; Yılmaz, Selahattin; Selamet, Yusuf
    In this study, carbon nanotubes (CNTs) added polyacrylonitrile/polypyrrole (PAN/PPy) electrospun nanofibers were produced. Average diameters of the nanofibers were measured as 268 and 153 nm for 10 and 25 wt% of PPy contents, respectively. A relatively higher strain to failure values (23.3%) were observed for the low PPy content. When as-grown CNTs (1 and 4 wt%) were added into the PAN/PPy blends, disordered nanofibers were observed to form within the microstructure. To improve the interfacial properties of CNTs/PAN/PPy composites, CNTs were functionalized with H2SO4/HNO3/HCl solution. The functionalized CNTs were well dispersed within the nanofibers and aligned along the direction of nanofibers. Therefore, beads formation on nanofibers decreased. The impedance of the nanofibers was found to decrease with the PPy content and CNT addition. These nanofibers had a great potential to be used as an electrochemical actuator or a tissue engineering scaffold.
  • Article
    Ultrasound Assisted Extraction for the Recovery of Phenolic Compounds From Waste Hazelnut Shell
    (Yıldız Teknik Üniversitesi, 2020) Dal, Orkan; Şengün, Duygu; Yüksel Özşen, Aslı
    Hazelnut shell is the primary byproduct of hazelnut industry which has the potential source of antioxidants, and phenolics with interest of pharmaceutical, food, and cosmetic industries. The main goal of this study is to determine effects of extraction method, extraction time, solvent type, solid to liquid ratio, and particle size on extraction yield, antioxidant capacity, and total phenolic content of waste hazelnut shell. The highest extraction yield was found as 15.4% by using methanol as solvent, in combined extraction for 16 h total extraction time. As for the best antioxidant capacity, 0.0508 mg TE mL-1 was observed by using methanol as a solvent in ultrasonic extraction, whereas the highest phenolic content was found as 0.188 mg GAE mL-1 by Soxhlet extraction with acetone for 8 h. After extraction of hazelnut shell waste, major components were found as oleic and palmitic acids for all solvent types according to GC-MS results.
  • Article
    Hydrothermal Treatment of Cellulose in Hot-Pressurized Water for Thr Production of Levulinic Acid
    (Uludağ Üniversitesi, 2016) Yüksel, Aslı
    Bu makalede selülozu değerli kimyasallara, özellikle levulinik asite, parçalamak amacı ile suyun kaynama noktası üzerinde ve kritik noktası altında (374. 15 °C ve 22.1 MPa) çalışılan sıcak-basınçlı su, reaksiyon ortamı olarak kullanılmıştır. Reaksiyon sıcaklığı, basıncı, süresi, oksitleme ajanı çeşidi ve miktarının selülozun parçalanmasına ve ürün dağılımına olan etkileri incelenmiştir. Selüloz bozunma yüzdesi ve levulinik asit oluşum verimini kıyaslamak amacı ile deneyler hem oksitleme ajanı (H2SO ve H2O) kullanarak, hem de kullanmayarak gerçekleştirilmiştir. Farklı sıcaklık (150 - 280 °C), basınç (5-64 bar) ve tepkime sürelerinde (30 - 120 dk.) oluşan likit ürünlerin analizleri HPLC ve GC-MS ile gerçekleştirilmiştir. Ana sıvı ürünler olarak levulinik asit, 5-HMF ve formik asit tespit edilmiştir. 125 mM sülfürik asit eklenerek 200 °C sıcaklıkta ve 60 dk boyunca gerçekleştirilen tepkime sonucunda, %73 selüloz bozunmuş ve %38 verimle levulinik asit elde edilmiştir.
  • Article
    Citation - WoS: 14
    Xenograft Tumor Volume Measurement in Nude Mice: Estimation of 3d Ultrasound Volume Measurements Based on Manual Caliper Measurements
    (Dokuz Eylül Üniversitesi, 2020) Barış, Mustafa; Serinan, Efe; Çalışır, Meryem; Şimşek, Kürşat; Aktaş, Safiye; Yılmaz, Osman; Seçil, Mustafa; Kılıç Özdemir, Sevgi
    Objectives: Volume measurement of subcutaneous xenograft tumors in nude mice models is an important metric to assess tumor growth or response to therapy. Manual calipers are widely used for this purpose. But the measurements with manual calipers may be inaccurate. Contrarily, three-dimensional (3D) ultrasonographic measurements give reliable and accurate tumor volume calculation. We aim to; evaluate the accuracy of common four formulas given in the literature to estimate xenograft tumor volumes based on manual caliper measurements and offer a new coefficient for a better estimation of the tumor volumes. Patients and Methods: Detailed manual diameter measurements of xenograft tumors were in 14 nude mice performed using Vernier caliper. Tumor volumes were calculated using the suggested formulas in the literature based on manual measurements. 3D ultrasound volume measurements were performed on same xenograft tumors using high resolution Vevo 2100 imaging system. To propose a new coefficient; means of ratio between manual and ultrasound volume measurement values were used. Also, data set was divided into two subgroups as tumor volume under 800 mm3 and over 800 mm3. New coefficients for each subgroup were defined. Results: Only with prolate ellipsoid formula there was no statistically significant difference between volume measurements with two methods (p=0,24). Our proposed formula (0,45 L*W*H) could estimate tumor volumes as good as prolate ellipsoid formula. Coefficient 0,35 and 0,81 in the same formula were found efficient in the selected subgroups. Conclusion: Using one common coefficient/formula for tumor volume estimation in any tumor size can be inaccurate. Appropriate coefficient should be chosen according to the dataset worked with.