Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
4 results
Search Results
Article Citation - WoS: 25Citation - Scopus: 26Lowering the Sintering Temperature of Solid Oxide Fuel Cell Electrolytes by Infiltration(Elsevier Ltd., 2019) Sındıraç, Can; Çakırlar, Seda; Büyükaksoy, Aligül; Akkurt, SedatA dense electrolyte with a relative density of over 95% is vital to prevent gas leakage and thus the achievement of high open circuit voltage in solid oxide fuel cells (SOFCs). The densification process of ceria based electrolyte requires high temperatures heat treatment (i.e. 1400-1500 degrees C). Thus, the minimum co-sintering temperatures of the anode-electrode bilayers are fixed at these values, resulting in coarse anode microstructures and consequently poor performance. The main purpose of this study is to densify gadolinia doped ceria (GDC), a common SOFC electrolyte, at temperatures lower than 1400 degrees C. By this aim, an approach involving the infiltration of polymeric precursors into porous electrolyte scaffolds, a method commonly used for composite SOFC electrodes, is proposed. By infiltrating polymeric precursors of GDC into porous GDC scaffolds, a reduction in the sintering temperature by at least 200 degrees C is achieved with no additives that might affect the electrical properties. Energy dispersive x-ray spectroscopy line scan analyses performed on porous GDC scaffolds infiltrated by a marker solution (polymeric FeOx precursor in this case) reveals a homogeneous infiltrated phase distribution, demonstrating the effectiveness of polymeric precursors.Article Citation - WoS: 4Citation - Scopus: 4Effects of Catalyst Precursor Type and Preparation Conditions, and Solvent Type on Activity and Selectivity of Pt/Sio2 Catalyst in Citral Hydrogenation(Walter de Gruyter GmbH, 2011) Depboylu, Can Okan; Yılmaz, Selahattin; Akkurt, SedatIn this study, citral hydrogenation reaction in liquid phase over silica gel supported Pt catalysts was investigated. It was desired to hydrogenate carbonyl group selectively to produce valuable unsaturated alcohols, namely geraniol and nerol. Pt/SiO2 catalysts were prepared by impregnation method. The effects of parameters investigated in the present study included Pt precursor type (hexachloroplatinic acid (HCLPA), platinum II acetylacetonate (PAA)), catalyst activation temperature (350°C and 450°C), catalyst activation without calcination, catalyst washing with 0.1 M NaOH and solvent type (ethanol, 2-pentanol). The catalysts activities and selectivities were affected by the type of precursor and activation temperature. The maximum citral conversion (89.50 percent) was achieved at lower activation temperature (350°C) with PAA precursor based catalyst. It was observed that higher activation temperature provided lower citral conversion but higher selectivity to unsaturated alcohols; increasing the activation temperature to 450°C decreased citral conversion to 26.10 percent. But selectivity to unsaturated alcohols, geraniol and nerol, increased from 7.06 to 54.60 percent. Catalyst washing and 2-pentanol prevented acetal formation. Catalyst activation without calcination gave lower citral conversion (20.84 percent) and selectivity to unsaturated alcohols (30.00 percent). Copyright © 2011 The Berkeley Electronic Press. All rights reserved.Conference Object Citation - Scopus: 1Microstructural Characterization of Industrial Chromite and Spinel Cement Kiln Refractories With Emphasis on the Iron-Rich Rims(Trans Tech Publications, 2004) Mercanköşk, Y.; Akkurt, Sedat; Çiftçioğlu, MuhsinMagnesia-chromite (MgO + MgO·Cr2O3) and magnesia-spinel (MgO + MgO·Al2O3) refractory bricks that are used in the high temperature zones of rotary cement kilns are investigated for their microstructural characteristics. Their microstructures are important because the size, shape and distribution of periclase grains, chromites and the quality of their bonding phases significantly affect their service performances. The purpose of this study was to characterize the microstructures of industrial brick samples to develop a protocol to compare different products e.g. for evaluation as replacement bricks. In some of the chromite containing bricks iron-rich rims were observed, while a domestic brick with similar chemistry had no such feature. These iron-rich rims were examined using SEM-EDS. It was found that the counter-diffusion of Fe+3 and Cr+3 were responsible for their formation. Exsolved chrome-spinel was widely observed in the microstructures of chromite bricks. Magnesia-spinel bricks were found to contain low melting calcium aluminates as bond phases in the microstructure, posing a threat to service performance. Portmortem microanalysis of industrially used bricks revealed alkali attack in addition to creep as main destruction mechanisms for brick. Traces of elements like Mo, S and alkalies were observed and thought to originate from the use of waste derived fuels.Conference Object Citation - WoS: 8Citation - Scopus: 8Low Temperature Synthesis of Spinel Powders by Mechanical Grinding(Trans Tech Publications, 2004) Yalamaç, Emre; Akkurt, Sedat; Çiftçioğlu, MuhsinLow temperature synthesis of spinel powder via intense mechanical grinding was performed. A dramatic decrease in the synthesis temperatures of ground powders was achieved. We were able to produce partially crystallized spinel at room temperature via a 110 minute grinding. Characterization of the synthesized powders was performed using SEM, XRD and DTA. Each stage of synthesis was analyzed using these techniques. Mixtures of Mg(OH)2 and Al(OH) 3 were used for synthesis. Temperatures as low as 800°C were able to produce bumps in the XRD patterns of ground powders at the 2θ angles for spinel crystals.