Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
6 results
Search Results
Article Citation - WoS: 10Citation - Scopus: 9Bi̇yomalzemelerden İ̇zole Edi̇len Staphylococcus Epidermidis Suşlarinin Yüzey Özelli̇kleri̇ni̇n Beli̇rlenmesi̇(Ankara Mikrobiyoloji Derneği, 2010) Sudağıdan, Mert; Erdem, İlker; Çavuşoğlu, Cengiz; Çiftçioğlu, MuhsinThe surface properties of bacteria play an important role on adhesion to the biomaterial surface. In this study, the surface properties of Staphylococcus epidermidis strains isolated from clinically used polymeric biomaterial surfaces were investigated on the basis of zeta potential, hydrophobicity and surface topography. A total of 10 S.epidermidis strains isolated from intravenous catheters (n= 5), endotracheal tubes (n= 3) and central venous catheters (n= 2) which were used in the patients of pulmonary Intensive Care Unit, Ege University Medical Faculty Hospital, were included to the study. Seven of those isolates were biofilm producers, inhabiting biofilm genes, 2 were non-biofilm producers, however, inhabiting biofilm genes, and 1 was non-biofilm producer, inhabiting no biofilm genes. Zeta potential analysis have been performed in 3 different buffers (phosphate-buffered saline, 1 mM potassium chloride and 1 mM potassium phosphate buffer) and at different pH values (pH 4.1-8.2), in order to simulate in vivo environment of the biomaterials. Hydrophobicities of the strains were examined by bacterial adhesion to hydrocarbon (BATH) test and the surface topography of biofilms and slime layers were visualized by atomic force microscopy (AFM) and scanning electron microscopy (SEM) methods. It was found that all strains have negative zeta potential values (surface charge) in all buffers and pH values. In hydrophobicity analysis, the highest value (86%) was determined for non-biofilm forming S.epidermidis strain YT-169b (endotracheal tube isolate) and the lowest hydrophobicity (2.5%) was determined for biofilm forming S.epidermidis strain YT-212 (central venous catheter isolate). Biofilm and slime layers of the strains were imaginated by AFM and SEM analysis in ?m scale. SEM analysis showed that bacteria highly adhered to rough surfaces on biomaterial surfaces and the produced slime layers covered the surface of bacteria. In conclusion, elucidating the surface properties of opportunistic pathogens in different physiologic buffers will give important clues for the production of non-adhesive materials and antibacterial surfaces for those bacteria. It was also estimated that designing the surface of the biomaterial to have negative surface charge in the body and to be as smooth as possible will hamper biofilm formation.Article Citation - WoS: 4Citation - Scopus: 3Modification of Surface Charge Characteristics for Unsupported Nanostructured Titania-Zirconia Uf/Nf Membrane Top Layers With Calcination Temperature(Springer, 2020) Erdem, İlker; Çiftçioğlu, MuhsinCeramic membranes are more advantageous alternatives especially for harsh working conditions when compared with the polymeric membranes. The porous multilayer structure of the ceramic membranes (composed of support, intermediate, and top layers) can be prepared via different oxides. Titania and zirconia, having superior properties, are mainly preferred for the top layer formation. The separation properties of the membrane are both dependent on pore morphology and surface charge of the oxide(s) forming the top layer. The effect of surface charge in separation may be very significant in case of filtration of charged species with relatively lower mass as in the ultrafiltration (UF) and nanofiltration (NF). In this study, unsupported membrane top layers were prepared with varying titania/zirconia ratios by sol-gel technique. Their surface charges at different pH conditions after calcination at varying temperatures (400 degrees, 500 degrees, and 600 degrees C) were determined. The surface charge of the pure titania (full Ti) top layer was decreasing with the increasing calcination temperature. The highest magnitudes of zeta potential for both acidic and basic conditions were measured via Zr rich top layer (TiZr2575) at calcination temperatures >= 500 degrees C, which was composed of anatase, rutile (titania), and tetragonal (zirconia) phases after calcination. The tailor-made top layer can be prepared with modifications during membrane preparation.Article Citation - Scopus: 2The Surface Charge of Unsupported Nano-Structured Titania Ceramic Membrane Top Layers With Varying Calcination Temperatures(University of Chemical Technology and Metallurgy, 2019) Erdem, İlker; Çiftçioğlu, MuhsinTitania is one of the most preferable ceramic membrane materials of superior durability (as zirconia) when compared to that of other ceramics, e.g. alumina or silica. The surface charge of the membrane top layer is an important parameter of the separation performance of the multilayer ceramic membrane due to the Donnan exclusion mechanisms. In this study, the change of the surface charge of unsupported nano-structured titania top layer is investigated with calcination temperature variation. The effect observed indicates the possibility of preparation of tailor-made top layers for multilayer ceramic membranes. © 2019, University of Chemical Technology and Metallurgy.Article Citation - WoS: 6Citation - Scopus: 7Influence of Calcination Temperature on Microstructure and Surface Charge of Membrane Top Layers Composed of Zirconia Nanoparticles(Springer Verlag, 2015) Erdem, İlker; Çiftçioğlu, MuhsinThe purpose of the research is to investigate the changes in microstructure and physicochemical characteristics, mainly surface charge (i.e. zeta potential) of zirconia membrane top layer during calcination. Zirconia is one of the most commonly preferred materials for ceramic membrane top layers due to its superior durability. The physicochemical properties of the top layer composed of submicron / nano particles is necessary not only for Donnan exclusion but also for dynamics of membrane fouling. In the present research the possibility of preparation of zirconia top layers with varying surface charge with changing calcination temperature was shown and a correlation between phase transformation and surface charge was determined.Article Citation - WoS: 21Citation - Scopus: 32Separation of Whey Components by Using Ceramic Composite Membranes(Elsevier Ltd., 2006) Erdem, İlker; Çiftçioğlu, Muhsin; Harsa, Hayriye ŞebnemCeramic supports were prepared from alumina powder and dip-coated with zirconia sol. The ceramic composite membranes prepared were characterized with respect to their microstructure/pore structures. The supports were 40% porous of which 87% were open pores. The average particle size of the sol particles was 35 nm. The prepared membrane has good protein lactose separation properties with a relatively high protein content (PR ∼80%) and with relatively low lactose retention (LR ∼7%). The permeate flux value was around 40 l/m2h. These results indicate the possibility of the preparation of ceramic composite membranes for separation of whey components with higher yields.Conference Object Citation - WoS: 5Citation - Scopus: 5Preparation of Ceramic Composite Membranes for Protein Separation(Trans Tech Publications, 2004) Erdem, İlker; Çiftçioğlu, Muhsin; Harsa, Hayriye ŞebnemCeramic supports were prepared from fine alumina and zirconia powders by dry-pressing and slip-casting. These supports were heat treated in the 1100° - 1200°C temperature range and dip-coated with ceramic sols prepared from alkoxides by using sol-gel methods. The average sol particle sizes were measured as 3-7 nm for zirconia and 30-40 nm for alumina by laser scattering technique. The optimum heat treatment temperature range was determined as 500°-600°C for dip-coated membranes by using TGA (thermo gravimetric analysis) results. The microstructure of the ceramic composite membranes was investigated by SEM (Scanning electron microscope). The clean water permeability (CWP) of the membranes was tested by using deionized water in a filtration set-up. Separation experiments were performed with bovine serum albumin (BSA, Stokes diameter: 7 nm) solution and whey to determine the protein separation capacity of the composite membranes. The CWP of the dry pressed alumina supports heat treated at 1100°C was found to be higher than the permeability of the slip-casted zirconia supports heat treated at 1200°C. The protein retention of the slip-casted zirconia support was determined as 60% by using UV-Vis spectrophotometer (Abs. at 280nm). A protein retention value of 96% was achieved for whey after the modification of the support with dip-coating. The permeate flux was 40 L/m2hour for dry-pressed alumina support dip-coated with zirconia sol calcined at 500°C.