Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
30 results
Search Results
Conference Object Citation - WoS: 24Effect of pH and Hydration on the Normal and Lateral Interaction Forces Between Alumina Surfaces(2006) Polat, Mehmet; Sato, Kimiyasu; Nagaoka, Takaaki; Watari, KojiNormal and lateral interaction forces between alumina surfaces were measured using Atomic Force Microscopy-Colloid Probe Method at different pH. The normal force curves exhibit a well-defined repulsive barrier and an attractive minimum at acidic pH and the DLVO theory shows excellent agreement with the data. The normal forces are always repulsive at basic pH and the theory fails to represent the measurements. Lateral forces are almost an order of magnitude smaller in the basic solutions. These differences, which have important implications in the study of stability and rheology, are attributed to the hydration of the alumina surface at basic pH. © 2013 Elsevier B.V., All rights reserved.Article Citation - WoS: 2Citation - Scopus: 3A Phenomenological Kinetic Flotation Model: Distinct Time-Variant Floatability Distributions for the Pulp and Froth Materials(Elsevier, 2023) Polat, Mehmet; Polat, HürriyetA simple and easy-to-use phenomenological kinetic flotation model, strongly connected with the physics of the process, is proposed in this paper. The model explicitly contains the cell volume, aeration rate, volumetric holdup, mean bubble size, and particle density as input variables. It can be employed to characterize the floatability distributions of the particles in the pulp and the froth separately any time during the flotation process. Two new time-dependent kinetic parameters, the bubble loading factor & phi;(t) and the maximum cell mass transfer capacity Mmax(t) also appear in the model expression. & phi;(t) is a measure of the degree of crowding of the bubble surfaces and accounts for the deviations from the first-order rate equation. Mmax(t) describes the maximum amount of mass that can be transported to the froth phase by the bubble population in the cell. Screen fractionation of each froth product collected at different time intervals during a single kinetic flotation test is sufficient to generate the data required by the model for analysis. Application of the model to this data yields directly time-dependent functions for the floatability of the particles reporting to froth Kf(t) or remaining in the cell Kp(t) for each size fraction separately, without the need for any empirical parameters. The test of the model was carried out using published kinetic flotation data from the literature.Article Citation - WoS: 6Citation - Scopus: 7Designing Robust Xylan/Chitosan Composite Shells Around Drug-Loaded Msns: Stability in Upper Git and Degradation in the Colon Microbiota(Elsevier, 2023) Zeybek, Nüket; Büyükkileci, Ali Oğuz; Güleç, Şükrü; Polat, Mehmet; Polat, Hürriyetong residence times, near-neutral pH values, and release triggered by the enzymatic action of the resident microbiota offer unique opportunities for improved drug delivery in the colon. The fact that a delivery agent must also pass through the complete GI tract without degradation presents a challenge due to widely changing pH conditions. In this study, a promising colon-targeted drug delivery system was composed of a xylan/chitosan composite shell formed on curcumin-loaded mesoporous silica nanoparticles (MSNs). A novel synthesis approach was employed to facilitate precipitation of negatively charged xylan on negatively charged MSNs by concurrent chitosan polymerization. Curcumin-loaded xylan/chitosan-coated MSNs (C-MSNs) were determined to contain nearly 42% xylan by the inclusion of chitosan in a one-to-one ratio with xylan. The xylan/chitosan composite shell demonstrated excellent stability in the acidic upper GI tract. The hydrolysis of glycosidic bonds by resident microbiota was the triggering mechanism for xylan degradation and curcumin release in the colon. The presence of xylan has the further benefit of increasing the number of beneficial bacteria and improving short-chain fatty acid production for improved colon health.Article Citation - WoS: 8Citation - Scopus: 11The Effect of Protein Bsa on the Stability of Lipophilic Drug (docetaxel)-Loaded Polymeric Micelles(Elsevier, 2021) Polat, Hürriyet; Çevik Eren, Merve; Polat, MehmetPolymeric micelles are promising delivery vehicles for improving the efficacy of anticancer drugs and reducing their side effects. However, considering the binding ability of serum albumin, the possible interaction of micelles with the native plasma components in the bloodstream raises serious questions on micellar stability. The stability of barren or drug-loaded copolymeric micelles was investigated systematically in distilled water (DW) and simulated body fluid (SBF) solutions in the presence of a model protein. The copolymer was a Pluronic® series triblock copolymer (P-123), the drug was strongly lipophilic docetaxel (DOC) and the protein was Bovine Serum Albumin (BSA). The effect of such factors as BSA and DOC concentrations and the aging of the micellar solutions was studied. Both the barren and drug-loaded micelles were quite stable in blank DW and SBF solutions for long times up to 10 days. They lost integrity and showed no inclination to re-assemble when the BSA concentration reached a critical value, which was very close to the plasma Human Serum Albumin (HSA) concentration. The presence of DOC in the micellar cores could not prevent disintegration. The results illustrate clearly that ensuring the stability of polymeric micelles in blood plasma should be an important design factor in their use as drug carriers.Article Citation - WoS: 4Citation - Scopus: 5Investigating the Effects of Ultrasonic Energy on the Flotation Behavior of Pyrite and Galena Minerals(Oficyna Wydawnicza Politechniki Wroclawsjiej, 2020) Horasan, Ümit; Tanrıverdi, Mehmet; Çicek, Tayfun; Polat, MehmetAlthough pyrite is one of the more abundant minerals of the earth crust, it has low economic value. When it reports to the concentrate during flotation along with the valuable minerals, it decreases the grade of the valuable minerals and leads to an increase in smelting costs. Numerous modifications have been suggested in the literature to increase the selective recovery of pyrite containing base metal-sulfide ores. The use of ultrasonic applications is one such method. In this study, the effect of the ultrasonic application on the flotation behavior of galena and pyrite mineral was investigated through systematic Hallimond Tube experiments. In the initial phase of the experiments, the optimum flotation conditions (particle size, pH, amount of air, and amount of reagent) were determined for the two minerals. Subsequent experiments were carried out under these optimums to distinguish the effect of the ultrasonic application. The influence of how the ultrasonic application was applied (i.e. before and during the conditioning stage or before the re-flotation of the concentrate) was also studied. It was observed that the ultrasonic application had a strong activating influence if it was administered before or during the conditioning stage. The effect was similar to whether the minerals were floated individually or from their mixtures. However, when it was applied to a flotation concentrate before re-flotation, it selectively displayed a depressant action for the pyrite to the extent that no depressants were needed. The results conclusively showed that the ultrasonic application could drastically improve the selectivity of the complex ores.Conference Object Effect of Some Physical, and Chemical Variables on Flocculation and Sediment Behaviour(A.A. Balkema Publishers, 2000) Polat, Hürriyet; Polat, Mehmet; İpekoğlu, ÜnerEffect of some chemical and physical variables on the settling rate, final sediment height, sediment viscosity and supernatant turbidity of a clay sample was studied using various polyacrylamide type flocculants. Increasing flocculant concentration significantly increased both the settling rate and sediment viscosity. More importantly, changes in the final sediment, height, hence the packing density, was minimal for all the conditions tested once the sediment was allowed to consolidate. Also, the mode of addition of the polymer, at once or continuous, did not seem to affect any of the parameters measured. Conditioning time seemed to alter the settling rate at low polymer concentrations, but had no effect at high polymer concentrations. However, increasing the conditioning time caused a decrease in the sediment viscosity. Different types of the polyacrylimides generated different settling rates at a given concentration, but the final sediment height was nearly independent of polymer type.Article Citation - WoS: 13Citation - Scopus: 15Analysis of Dilution Induced Disintegration of Micellar Drug Carriers in the Presence of Inter and Intra Micellar Species(Elsevier, 2020) Polat, Hürriyet; Kutluay, Gülistan; Polat, MehmetMicelles of self-assembling polymeric surfactant molecules are promising nanoscopic carriers for lipophilic and toxic drugs, genes, and imaging molecules. Though it is a must for successful transport, ensuring micelle integrity is a challenge during intravenous injection where micelles must endure abrupt dilutional effects and encounters with native molecules. Therefore, direct observational evidence of how micelles behave during dilution is valuable in manipulating the designs of these carriers for a succesful drug delivery. Morphology and stability of the barren and a drug-loaded (lipophilic probucol) micelles of a polymeric surfactant (Pluronic® P123) were monitored during systematic re-dilution in distilled water and simulated body fluid in the presence of a model protein (bovine serum albumin). It was observed through surface tension, dynamic light scattering, laser velocimetry, transmission scanning and transmission electron microscopy, and atomic force microscopy analyses that the micelles disintegrated to various degrees in all cases upon dilution. The results indicate that dilution effects must be taken into account in designing micellar drug carriers. The assistance of some other means of protection such as encapsulation should be considered for ensuring micelle integrity within the bloodstream. © 2020 Elsevier B.V.Article Citation - WoS: 16Citation - Scopus: 19Designing of Spherical Chitosan Nano-Shells With Micellar Cores for Solvation and Safeguarded Delivery of Strongly Lipophilic Drugs(Elsevier Ltd., 2017) Cihan, Esra; Polat, Mehmet; Polat, HürriyetChitosan is a very effective biopolymer for drug delivery purposes due to its biocompatibility, positive charge and exceptionally pH sensitive degradability behavior in an aqueous medium. Nevertheless, its inability for dissolving lipophilic drug active material and the difficulties in controlling the size and shape of the synthesized particles in nanometer range are critical drawbacks in its effective use. In this study, a synthesis procedure which addresses both issues simultaneously is presented. The procedure is based on initial dissolution of lipophilic drug molecules within the hydrophobic cores of the micelles of a bio-compatible block-copolymer by ionic gelation and subsequent formation of a chitosan shell by polymerization around the micellar structures. Well-formed, hollow and perfectly spherical chitosan particles (nano-shells) in the 30–300 nm size range could be successfully manufactured. Characterization by STEM, TEM, AFM, FTIR and DLS, DLS-LDV techniques showed clearly that the drug was successfully incorporated into the chitosan structure. It was demonstrated that the particles enveloped the micelle(s) of a Pluronic copolymer (P-123) whose hydrophobic cores contained a strongly hydrophobic drug Probucol. The chitosan nano-shells are expected to act as an agent protecting the integrity of the drug-loaded micelles in the body fluid while providing a pH sensitive release medium. The drug uptake by the chitosan particles was very high. A very sharp increase in the amount of the drug released with a slight change in the acidity of the medium was an indication of the potential of the manufactured chitosan nano-shells as pH sensitive, target specific delivery vehicles for drug release.Article Citation - WoS: 13Citation - Scopus: 15Ancillary Effects of Surfactants on Filtration of Low Molecular Weight Contaminants Through Cellulose Nitrate Membrane Filters(Elsevier Ltd., 2016) Olcay, Aybike Nil; Polat, Mehmet; Polat, HürriyetRemoval of contaminants with low molecular weight (<800 Dalton) requires the use of advanced separation techniques such as ultrafiltration (UF) or micellar enhanced ultrafiltration (MEUF). However, surface active agents invariably co-exist in waste waters along with these contaminants or they may be added intentionally as part of the separation process as in the case of MEUF. Though it is quite likely that both the filter medium and the contaminants would interact with the surfactant molecules or their micelles, there is not sufficient emphasis in the literature on the concomitant aspects of such interactions.The ancillary effects created by anionic (sodium dodecyl sulfate, SDS), cationic (hexadecyltrimethyl ammonium bromide, CTAB) and non-ionic (ethoxylated octylphenol, TX-100) surfactants on the mechanism and efficiency of the filtration process were investigated in this study. Methylene blue (MB) and cellulose nitrate membrane (CNM) filters were employed as model retentate and the separation medium. A combination of surface tension, contact angle and charge measurements demonstrated that the addition of surfactants had a remarkable effect on the filtration outcome. The effect depended on both the type and concentration of the surfactant and was manifested mainly through the creation of MB-surfactant entities which acted differently than the MB alone; but more importantly, through the interactions of the surfactant molecules/micelles and the MB-surfactant pairs with the separation membrane.Article Citation - WoS: 22Citation - Scopus: 26Coal Fly Ash as a Potential Fixation Reagent for Radioactive Wastes(Elsevier Ltd., 2015) Lieberman, Roy Nir; Green, Uri; Segev, Giora; Polat, Mehmet; Mastai, Yitzhak; Cohen, HaimIsrael produces ∼1.3 Mt/year of fly ash (FA), a byproduct of its coal-fired power plants. Due to increasing environmental regulations, these imported coals are processed to reduce the sulfur concentration (∼0.6%). These processing methods result in a material that has an enriched alkali/alkali earth component with pozzolanic and basic properties (pH > 10.5). FAs are utilized worldwide, mainly as a cement additive for the construction industry. Recently, it was demonstrated that Class F FA can act as an excellent fixation reagent for acidic wastes from the phosphate or the oil regeneration industries. In the current work the potential utilization of Class F FAs as fixation reagents for low-activity radioactive waste from the nuclear industry was examined. Aqueous solutions containing radionuclide simulants: cesium (Cs+), strontium, (Sr2+), and cerium (Ce3+, Ce4+) were used as case studies with promising results. It is suggested that the primary fixation mechanism involves the aluminate/silicate anions at the FA surface. A novel experimental fixation approach utilizing the formation of carbonates is demonstrated and a new interaction mechanism is suggested based on the electrostatic interactions of the positively charged fine precipitates with the negatively charged FA surface. © 2015 Elsevier Ltd. All rights reserved.
- «
- 1 (current)
- 2
- 3
- »