Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
3 results
Search Results
Article Citation - WoS: 11Citation - Scopus: 13Effect of Cnt Incorporation on Pan/Ppy Nanofibers Synthesized by Electrospinning Method(TÜBİTAK, 2020) İnce Yardımcı, Atike; Selamet, Yusuf; Tanoğlu, Metin; Tanoğlu, Metin; Yılmaz, Selahattin; Yılmaz, Selahattin; Selamet, Yusuf; 03.02. Department of Chemical Engineering; 03.10. Department of Mechanical Engineering; 04.05. Department of Pyhsics; 03. Faculty of Engineering; 04. Faculty of Science; 01. Izmir Institute of TechnologyIn this study, carbon nanotubes (CNTs) added polyacrylonitrile/polypyrrole (PAN/PPy) electrospun nanofibers were produced. Average diameters of the nanofibers were measured as 268 and 153 nm for 10 and 25 wt% of PPy contents, respectively. A relatively higher strain to failure values (23.3%) were observed for the low PPy content. When as-grown CNTs (1 and 4 wt%) were added into the PAN/PPy blends, disordered nanofibers were observed to form within the microstructure. To improve the interfacial properties of CNTs/PAN/PPy composites, CNTs were functionalized with H2SO4/HNO3/HCl solution. The functionalized CNTs were well dispersed within the nanofibers and aligned along the direction of nanofibers. Therefore, beads formation on nanofibers decreased. The impedance of the nanofibers was found to decrease with the PPy content and CNT addition. These nanofibers had a great potential to be used as an electrochemical actuator or a tissue engineering scaffold.Article Citation - WoS: 18Citation - Scopus: 17Cnt Incorporated Polyacrilonitrile/Polypyrrole Nanofibers as Keratinocytes Scaffold(Trans Tech Publications, 2019) Meşe Özçivici, Gülistan; Selamet, Yusuf; Özçivici, Engin; Yılmaz, Selahattin; Özçivici, Engin; Meşe, Gülistan; Selamet, Yusuf; 03.01. Department of Bioengineering; 03.02. Department of Chemical Engineering; 04.03. Department of Molecular Biology and Genetics; 04.05. Department of Pyhsics; 03. Faculty of Engineering; 04. Faculty of Science; 01. Izmir Institute of TechnologyPolypyrrole (PPy) is an attractive scaffold material for tissue engineering with its non-toxic and electrically conductive properties. There has not been enough information about PPy usage in skin tissue engineering. The aim of this study is to investigate biocompatibility of polyacrilonitrile (PAN)/PPy nanofibrous scaffold for human keratinocytes. PAN/PPy bicomponent nanofibers were prepared by electrospinning, in various PPy concentrations and with carbon nanotube (CNT) incorporation. The average diameter of electrospun nanofibers decreased with increasing PPy concentration. Further, agglomerated CNTs caused beads and disordered parts on the surface of nanofibers. Biocompatibility of these PAN/PPy and PAN/PPy/CNT scaffolds were analyzed in vitro. Both scaffolds provided adhesion and proliferation of keratinocytes. Nanofiber diameter did not significantly influence the morphology of cells. However, with increasing number of cells, cells stayed among nanofibers and this affected their shape and size. In this study, we demonstrated that PAN/PPy and PAN/PPy/CNT scaffolds enabled the growth of keratinocytes, showing their biocompatibility.Article Citation - WoS: 54Citation - Scopus: 62Sic-Particulate Aluminum Composite Foams Produced by Powder Compacts: Foaming and Compression Behavior(Springer Verlag, 2003) Elbir, Semih; Yılmaz, Selahattin; Güden, Mustafa; Güden, Mustafa; Hall, Ian W.; Yılmaz, Selahattin; 03.02. Department of Chemical Engineering; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologyThe foaming behavior of SiC-particulate (8.6% by volume) aluminum composite powder compacts contained Titanium Hydride blowing agent was investigated by heating above the melting temperature (750°C) in a pre-heated furnace. Aluminum powder compacts were also prepared and foamed using similar compaction and foaming parameters in order to determine the effect of SiC-particulate addition on foaming and compression behavior. The linear expansions of the compacts at various furnace holding times were ex situ determined. Optical and scanning electron microscopy techniques were used to characterize prepared and deformed foams microstructures. The SiC-particulate addition was found to increase the linear expansion and reduce the extent of the liquid metal drainage and cell coarsening of the aluminum compacts. The composite foam samples also showed higher compressive stresses, but a more brittle behavior as compared with aluminum foams.