Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
5 results
Search Results
Article Citation - WoS: 6Citation - Scopus: 9Preparation and Characterization of Flexible Polyvinylchloride-Copper Composite Films(Smithers Rapra Technology, 2013) Kurt, Emrah; Özçelik, Cenk Yağız; Yetgin, Senem; Özmıhçı Ömürlü, Filiz; Balköse, DevrimFlexible PVC films are statically charged due to their low electrical conductivity. This creates fire threat during its handling. Conductive materials are added to films to prevent this. In the present study it was aimed to prepare PVC- copper composite films by sol gel technique and characterize the prepared films. It was aimed to increase the electrical conductivity of the films by adding copper powder. However, the copper particles settled down to bottom instead of forming a conductive network that covers the whole cross section. Thus at the film crosssection a plastic upper phase and a copper rich lower phase were present. The film did not conduct electricity due to this uneven distribution. The minimum volumetric and surface resistivities of the films were at the order of 109 ohm-cm and 1010 ohm square respectively.Article Citation - WoS: 2Citation - Scopus: 2Morphology of Sodium Salt of Calf Thymus Dna on Mica, Alumina, and Silica Surfaces: Effect of Solvent and Drying Method(Taylor and Francis Ltd., 2017) Yetgin, Senem; Balköse, DevrimInvestigation of morphology of deoxyribonucleotide triphosphate (DNA) dried on different surfaces by atomic force microscopy (AFM) is important in DNA research that is focused on subjects of condensation for gene therapy, sizing, DNA mapping, and cancer examination. The solvent, the surface type, and the method of drying effect the morphology of DNA on solid surfaces. Ethanol and water were used as solvents, flat mica, silica, and alumina surfaces were used as the substrates in the present study. Different methods such as ambient air-drying, N2-forced flow regime drying, and freeze-drying have been applied to droplets of DNA solutions in water or ethanol on the substrates. Forced flow drying regime causes nonlinear DNA attachment on the surface and self-assembly. DNA vertical distance on mica surface was found to be 6 and 1.4 nm for DNA dried in ambient air from ethanol and water solutions, respectively. It was 1.6 nm for N2 flow drying of aqueous DNA solution on mica surface. It was 4.6, 4.6, and 1.99 nm for ambient, N2 flow, and freeze-dried aqueous DNA on alumina surfaces, respectively. Aqueous solution of DNA dried under N2 flow on silica surface had 0.8 nm vertical distance. The smallest standard deviation of 0.05 nm was observed for DNA dried under N2 flow on alumina surface.Article Citation - WoS: 5Citation - Scopus: 5Methylene Blue Adsorption From Aqueous Solutions To Flexible Poly(vinyl Chloride) Silica Composites(John Wiley and Sons Inc., 2015) Yetgin, Senem; Ulutan, Sevgi; Balköse, DevrimMethylene blue (MB) adsorption studies were performed with poly(vinyl chloride)-(dioctyl phthalate)-silica composites, which were obtained by using plastisol-plastigel technology. The films were flexible, having elastic modulus of 1.0-1.5 GPa. Diminishing MB concentration in the aqueous phase was followed as the adsorption process advanced by using visible spectroscopy. Contributions of the individual components of the composites to adsorption were also investigated. Although the MB adsorption capacity was extensively high for silica, it was moderate for the composite, most likely owing to the occlusion of pores of silica by plasticizer to some extent. The improvement of MB adsorption capacity of the composites as the silica ratio increased was explicitly deduced from the optical microscopy photographs. The diffusion coefficients of MB through the composites were 5 × 10-13, 6 × 10-13, and 3 × 10-13 m2 s-1 with regression coefficients of 0.73, 0.89, and 0.88 for 0, 2, and 16% silica-containing composites, respectively. Because of the slow diffusion of MB in poly(vinyl chloride)-silica composites, using them as dynamic column adsorbent was not practical. However, these versatile plastics can be used as plastic labels, colored clothing, leather substitutes, antimicrobial medical devices, and laser printable surfaces.Article Citation - WoS: 6Citation - Scopus: 7Preparation and Characterization of Flexible Poly(vinyl Chloride) Foam Films(John Wiley and Sons Inc., 2012) Şahin, Erdem; Yaşar Mahlıçlı, Filiz; Yetgin, Senem; Balköse, DevrimIn this study, the effect of activator ZnO and heating time at 190°C on foaming, gelation, and dehydrochlorination of poly(vinyl chloride) (PVC) plastisol was investigated. For this purpose, a PVC plastisol was prepared by mixing PVC, dioctyl phthalate (DOP), azodicarbonamide (ADC), ZnO, and the heat stabilizers calcium stearate (CaSt 2) and zinc stearate(ZnSt 2). PVC plastisol films were heated for 3, 6, 12, and 24 min periods at 190°C to see the effect of heating time on the gelation and foaming processes of the PVC foam. The time of 12 min was determined to be optimum for the completion of gelation and foaming processes without thermal degradation of PVC. No foaming was observed under the same conditions for the samples without ZnO. ZnO had a significant catalytic effect on ADC decomposition, accelerating the foaming of the films. Average porosity measurement showed a consistent increase in porosity with heating time up to 76% and the average density decreased from 1.17 to 0.29 g/cm 3 on foaming. Tensile tests showed that the tensile strength and tensile strain both increased considerably up to 0.98 MPa and 207%, respectively, with heating time and the elastic modulus was seen to gradually decrease from 4.7 to 0.7 MPa with heating time. Films without ZnO had higher tensile strength since there were no pores. PVC thermomat tests showed that ZnO lowered the stability time of plastigel film with azodicarbonamide.Article Citation - WoS: 1Citation - Scopus: 1Flexible Pvc-Silica Composites as an Adsorptive Material for Water Soluble Dyes(Smithers Rapra Technology, 2013) Ulutan, Sevgi; Yetgin, Senem; Balköse, DevrimMethylene Blue (MB) adsorption studies were performed on flexible Polyvinyl Chloride/Silica composites which were obtained by using plastisol-plastigel technology. Change of MB concentration in aqueous phase as the adsorption process advanced was followed by using visible spectroscopy. The diffusion of MB through the composites exhibited non-Fickian behavior with a diffusivity of 10-11 m2s-1. Making use of such PVC-silica composite sheets as column packing, the packing time will be reduced and the surface available for diffusion will be increased. © 2013 Smithers Rapra Technology.