Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
5 results
Search Results
Article Citation - WoS: 6Citation - Scopus: 9Preparation and Characterization of Flexible Polyvinylchloride-Copper Composite Films(Smithers Rapra Technology, 2013) Kurt, Emrah; Özçelik, Cenk Yağız; Yetgin, Senem; Özmıhçı Ömürlü, Filiz; Balköse, DevrimFlexible PVC films are statically charged due to their low electrical conductivity. This creates fire threat during its handling. Conductive materials are added to films to prevent this. In the present study it was aimed to prepare PVC- copper composite films by sol gel technique and characterize the prepared films. It was aimed to increase the electrical conductivity of the films by adding copper powder. However, the copper particles settled down to bottom instead of forming a conductive network that covers the whole cross section. Thus at the film crosssection a plastic upper phase and a copper rich lower phase were present. The film did not conduct electricity due to this uneven distribution. The minimum volumetric and surface resistivities of the films were at the order of 109 ohm-cm and 1010 ohm square respectively.Article Citation - WoS: 2Citation - Scopus: 2Morphology of Sodium Salt of Calf Thymus Dna on Mica, Alumina, and Silica Surfaces: Effect of Solvent and Drying Method(Taylor and Francis Ltd., 2017) Yetgin, Senem; Balköse, DevrimInvestigation of morphology of deoxyribonucleotide triphosphate (DNA) dried on different surfaces by atomic force microscopy (AFM) is important in DNA research that is focused on subjects of condensation for gene therapy, sizing, DNA mapping, and cancer examination. The solvent, the surface type, and the method of drying effect the morphology of DNA on solid surfaces. Ethanol and water were used as solvents, flat mica, silica, and alumina surfaces were used as the substrates in the present study. Different methods such as ambient air-drying, N2-forced flow regime drying, and freeze-drying have been applied to droplets of DNA solutions in water or ethanol on the substrates. Forced flow drying regime causes nonlinear DNA attachment on the surface and self-assembly. DNA vertical distance on mica surface was found to be 6 and 1.4 nm for DNA dried in ambient air from ethanol and water solutions, respectively. It was 1.6 nm for N2 flow drying of aqueous DNA solution on mica surface. It was 4.6, 4.6, and 1.99 nm for ambient, N2 flow, and freeze-dried aqueous DNA on alumina surfaces, respectively. Aqueous solution of DNA dried under N2 flow on silica surface had 0.8 nm vertical distance. The smallest standard deviation of 0.05 nm was observed for DNA dried under N2 flow on alumina surface.Article Citation - WoS: 11Citation - Scopus: 12Calf Thymus Dna Characterization and Its Adsorption on Different Silica Surfaces(Royal Society of Chemistry, 2015) Yetgin, Senem; Balköse, DevrimDNA adsorption is the initial stage of gene therapy for drug delivery systems and solid phase extraction methods of DNA purification. High pore volume and high adsorption capacity are simple requirements not only for producing 'smart' drug delivery systems but also the development of purification kits. Silica is the most used material for this purpose. The present study aimed at elucidating the calf thymus DNA biosorption process by the characterization of calf thymus DNA and silica to increase the efficiency of the currently used silica material. Mesoporous silica has long been used for DNA adsorption and silica aerogel is the new adsorbent investigated in the present study. When DNA solution was freeze dried on a silica wafer, self-assembled super helices formed as shown by atomic microscopy (AFM). Thus DNA existed not as single molecules but as large sized agglomerates in water. Thus it could be adsorbed in the macropores and on the external surface of adsorbents. Adsorption of calf thymus DNA to a silica aerogel, a mesoporous silica gel and a silica wafer was investigated in the present study. Silica aerogel was synthesized from TEOS by a supercritical ethanol drying process. The DNA adsorption capacity of the silica aerogel was nearly two times that of the mesoporous silica gel due to its macroporous structure and its higher silanol content. Silica aerogel was found to be a very promising material for DNA adsorption. Therefore silica aerogel can be considered as a good candidate for the delivery of DNA.Article Citation - WoS: 1Citation - Scopus: 1Flexible Pvc-Silica Composites as an Adsorptive Material for Water Soluble Dyes(Smithers Rapra Technology, 2013) Ulutan, Sevgi; Yetgin, Senem; Balköse, DevrimMethylene Blue (MB) adsorption studies were performed on flexible Polyvinyl Chloride/Silica composites which were obtained by using plastisol-plastigel technology. Change of MB concentration in aqueous phase as the adsorption process advanced was followed by using visible spectroscopy. The diffusion of MB through the composites exhibited non-Fickian behavior with a diffusivity of 10-11 m2s-1. Making use of such PVC-silica composite sheets as column packing, the packing time will be reduced and the surface available for diffusion will be increased. © 2013 Smithers Rapra Technology.Article Citation - WoS: 21Citation - Scopus: 23Activated Carbon Adsorption of Fuel Oxygenates Mtbe and Etbe From Water(Springer Verlag, 2009) İnal, Fikret; Yetgin, Senem; Aksu, Gülsüm T.; Şimşek, Selvi; Sofuoğlu, Aysun; Sofuoğlu, Sait CemilThe aqueous phase adsorption of fuel oxygenates methyl tertiary butyl ether (MTBE) and ethyl tertiary butyl ether (ETBE) onto commercially available granular activated carbon (GAC; Norit GAC 1240) was investigated in a batch system at 27°C. The oxygenate concentrations were determined by headspace gas chromatography/mass spectrometry analyses. The experimental data were used with four two-parameter isotherm models (Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich) and two kinetic models (pseudo first-order and pseudo second-order) to determine equilibrium and kinetic parameters. Considering the correlation coefficient and root mean square error, Dubinin-Radushkevich isotherm showed better fit with the equilibrium data for MTBE. However, the performances of Langmuir and Dubinin-Radushkevich models were comparable for ETBE. The adsorption capacities were calculated as 5.50 and 6.92 mg/g for MTBE and ETBE, respectively, at an equilibrium solution concentration of 1 mg/L using Dubinin-Radushkevich isotherm. The differences between the model predictions and experimental data were similar for the pseudo first-order and pseudo second-order kinetic models. Gibbs free-energy changes of adsorption were found to be -22.59 and -28.55 kJ/mol for MTBE-GAC and ETBE-GAC systems, respectively, under the experimental conditions studied.