Chemical Engineering / Kimya Mühendisliği

Permanent URI for this collectionhttps://hdl.handle.net/11147/14

Browse

Filters

2003 - 20053

Settings

End date: 2009Department: search.filters.department.İzmir Institute of Technology. Materials Science and Engineering

Search Results

Now showing 1 - 3 of 3
  • Article
    Citation - WoS: 35
    Citation - Scopus: 42
    Membrane Formation by Dry-Cast Process: Model Validation Through Morphological Studies
    (Elsevier Ltd., 2005) Alsoy Altınkaya, Sacide; Yenal, Hacer; Özbaş, Bülent
    Asymmetric membranes were prepared by dry-cast phase inversion technique from a cellulose acetate, acetone, water solution in order to assess the validity of the mathematical model recently developed by us. Based on the model predictions, general structural characteristics of the membranes were determined by plotting the composition paths on the ternary phase diagram and polymer concentration profile at the first moment of precipitation. Composition paths on the ternary phase diagram enable the assessment of whether a phase separation occurs and allow prediction of inception time and duration of the phase separation. The polymer distribution at the moment of precipitation provides a rough thickness of the high polymer concentration region near the interface and a pore distribution of the sublayer structure. The effects of polymer/nonsolvent ratio in the casting solution, the initial film thickness, evaporation temperature, relative humidity and velocity of air were investigated. Model predictions were compared with the morphological analysis conducted using scanning electron microscopy. Results show that diffusion formulation plays an important role in capturing the accurate structure of the membrane from the model predictions.
  • Article
    Citation - WoS: 50
    Citation - Scopus: 65
    Modeling of Asymmetric Membrane Formation by Dry-Casting Method
    (Elsevier Ltd., 2004) Alsoy Altınkaya, Sacide; Özbaş, Bülent
    Many polymeric membranes are produced by phase inversion technique invented by Loeb and Sourirajan in 1962. The dry-casting method is one of the major phase inversion techniques in which a homogeneous polymer solution consisting of solvent(s) and nonsolvent(s) is cast on a support and then evaporation of the casting solution takes place under convective conditions. In this paper, we model membrane formation by the dry-casting method. The model takes into account film shrinkage, evaporative cooling, coupled heat, and mass transfer and incorporates practical and reliable diffusion theory as well as complex boundary conditions especially at the polymer solution/air interface. The predictions from the model provide composition paths, temperature, and thickness of the solution. By plotting the composition paths on the ternary phase diagram, we ascertain the general structural characteristics of the membranes prepared from particular casting conditions. The predictive ability of the model was evaluated by comparing the results with the experimental data obtained from gravimetric measurements for cellulose acetate (CA)-acetone-water system. In an attempt to illustrate the importance of diffusion formalism on the predictions, recently proposed multicomponent diffusion theory and its simplified forms were utilized in the model. The computational results show that the critical factor for capturing the accurate behavior of membrane formation is the diffusion formalism utilized in the model
  • Article
    Citation - WoS: 54
    Citation - Scopus: 62
    Sic-Particulate Aluminum Composite Foams Produced by Powder Compacts: Foaming and Compression Behavior
    (Springer Verlag, 2003) Elbir, Semih; Yılmaz, Selahattin; Toksoy, Ahmet Kaan; Güden, Mustafa; Hall, Ian W.
    The foaming behavior of SiC-particulate (8.6% by volume) aluminum composite powder compacts contained Titanium Hydride blowing agent was investigated by heating above the melting temperature (750°C) in a pre-heated furnace. Aluminum powder compacts were also prepared and foamed using similar compaction and foaming parameters in order to determine the effect of SiC-particulate addition on foaming and compression behavior. The linear expansions of the compacts at various furnace holding times were ex situ determined. Optical and scanning electron microscopy techniques were used to characterize prepared and deformed foams microstructures. The SiC-particulate addition was found to increase the linear expansion and reduce the extent of the liquid metal drainage and cell coarsening of the aluminum compacts. The composite foam samples also showed higher compressive stresses, but a more brittle behavior as compared with aluminum foams.