Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
78 results
Search Results
Conference Object Citation - WoS: 24Effect of pH and Hydration on the Normal and Lateral Interaction Forces Between Alumina Surfaces(2006) Polat, Mehmet; Sato, Kimiyasu; Nagaoka, Takaaki; Watari, KojiNormal and lateral interaction forces between alumina surfaces were measured using Atomic Force Microscopy-Colloid Probe Method at different pH. The normal force curves exhibit a well-defined repulsive barrier and an attractive minimum at acidic pH and the DLVO theory shows excellent agreement with the data. The normal forces are always repulsive at basic pH and the theory fails to represent the measurements. Lateral forces are almost an order of magnitude smaller in the basic solutions. These differences, which have important implications in the study of stability and rheology, are attributed to the hydration of the alumina surface at basic pH. © 2013 Elsevier B.V., All rights reserved.Article Citation - WoS: 10Citation - Scopus: 9Bi̇yomalzemelerden İ̇zole Edi̇len Staphylococcus Epidermidis Suşlarinin Yüzey Özelli̇kleri̇ni̇n Beli̇rlenmesi̇(Ankara Mikrobiyoloji Derneği, 2010) Sudağıdan, Mert; Erdem, İlker; Çavuşoğlu, Cengiz; Çiftçioğlu, MuhsinThe surface properties of bacteria play an important role on adhesion to the biomaterial surface. In this study, the surface properties of Staphylococcus epidermidis strains isolated from clinically used polymeric biomaterial surfaces were investigated on the basis of zeta potential, hydrophobicity and surface topography. A total of 10 S.epidermidis strains isolated from intravenous catheters (n= 5), endotracheal tubes (n= 3) and central venous catheters (n= 2) which were used in the patients of pulmonary Intensive Care Unit, Ege University Medical Faculty Hospital, were included to the study. Seven of those isolates were biofilm producers, inhabiting biofilm genes, 2 were non-biofilm producers, however, inhabiting biofilm genes, and 1 was non-biofilm producer, inhabiting no biofilm genes. Zeta potential analysis have been performed in 3 different buffers (phosphate-buffered saline, 1 mM potassium chloride and 1 mM potassium phosphate buffer) and at different pH values (pH 4.1-8.2), in order to simulate in vivo environment of the biomaterials. Hydrophobicities of the strains were examined by bacterial adhesion to hydrocarbon (BATH) test and the surface topography of biofilms and slime layers were visualized by atomic force microscopy (AFM) and scanning electron microscopy (SEM) methods. It was found that all strains have negative zeta potential values (surface charge) in all buffers and pH values. In hydrophobicity analysis, the highest value (86%) was determined for non-biofilm forming S.epidermidis strain YT-169b (endotracheal tube isolate) and the lowest hydrophobicity (2.5%) was determined for biofilm forming S.epidermidis strain YT-212 (central venous catheter isolate). Biofilm and slime layers of the strains were imaginated by AFM and SEM analysis in ?m scale. SEM analysis showed that bacteria highly adhered to rough surfaces on biomaterial surfaces and the produced slime layers covered the surface of bacteria. In conclusion, elucidating the surface properties of opportunistic pathogens in different physiologic buffers will give important clues for the production of non-adhesive materials and antibacterial surfaces for those bacteria. It was also estimated that designing the surface of the biomaterial to have negative surface charge in the body and to be as smooth as possible will hamper biofilm formation.Article Citation - WoS: 54Citation - Scopus: 64Bioactive Fish Scale Incorporated Chitosan Biocomposite Scaffolds for Bone Tissue Engineering(Elsevier Ltd., 2019) Kara, Aylin; Tamburacı, Sedef; Tıhmınlıoğlu, Funda; Havıtçıoğlu, HasanRecently, biologically active natural macromolecules have come into prominence to be used as potential materials in scaffold design due to their unique characteristics which can mimic the human tissue structure with their physical and chemical similarity. Among them, fish scale (FS) is a biologically active material with its structural similarity to bone tissue due to including type I collagen and hydroxyapatite and also have distinctive collagen arrangement. In the present study, it is aimed to design a novel composite scaffold with FS incorporation into chitosan (CH) matrix for bone tissue regeneration. Therefore, two biological macromolecules, fish scale and chitosan, were combined to produce bio-composite scaffold. First, FS were decellularized with the chemical method and disrupted physically as microparticles (100 in), followed by dispersal in CH with ultrasonic homogenisation, CH/FS scaffolds were fabricated by lyophilization technique. Scaffolds were characterized physically, chemically, mechanically, and morphologically. SEM and porosity results showed that CH/FS scaffolds have uniform pore structure showing high porosity. Mechanical properties and degradation rate are enhanced with increasing FS content. In vitro cytotoxicity, proliferation and osteogenic activity of the scaffolds were evaluated with SaOS-2 cell line. CH/FS scaffolds did not show any cytotoxicity effect and the cells were gradually proliferated during culture period. Cell viability results showed that, FS microparticles had a proliferative effect on SaOS-2 cells when compared to control group. ALP activity and biomineralization studies indicated that FS micro particle reinforcement increased osteogenic activity during culture period. As a biological macromolecule with unique characteristics, FS was found as cytocompatible and provided promising effects as reinforcement agents for polymeric scaffolds. In conclusion, fabricated CH/FS bio-composites showed potential for bone tissue engineering applications. (C) 2019 Elsevier B.V. All rights reserved.Article Citation - WoS: 43Citation - Scopus: 47Bioactive Diatomite and Poss Silica Cage Reinforced Chitosan/Na-carboxymethyl Cellulose Polyelectrolyte Scaffolds for Hard Tissue Regeneration(Elsevier, 2019) Tamburacı, Sedef; Kimna, Ceren; Tıhmınlıoğlu, FundaRecently, natural polymers are reinforced with silica particles for hard tissue engineering applications to induce bone regeneration. In this study, as two novel bioactive agents, effects of diatomite and polyhedral oligomeric silsesquioxanes (POSS) on chitosan (CS)/Na-carboxymethylcellulose (Na-CMC) polymer blend scaffolds are examined. In addition, the effect of silica reinforcements was compared with Si-substituted nano-hydroxyapatite (Si-Hap) particles. The morphology, physical and chemical structures of the scaffolds were characterized with SEM, liquid displacement, FT-IR, mechanical analysis, swelling and degradation studies. The particle size and the crystal structure of diatomite, POSS and Si-Hap particles were determined with DLS and XRD analyses. In vitro studies were performed to figure out the cytotoxicity, proliferation, ALP activity, osteocalcin production and biomineralization to demonstrate the promising use of natural silica particles in bone regeneration. Freeze-dried scaffolds showed 190-307 mu m pore size range and 61-70% porosity. Both inorganic reinforcements increased the mechanical strength, enhanced the water uptake capacity and fastened the degradation rate. The nanocomposite scaffolds did not show any cytotoxic effect and enhanced the surface mineralization in osteogenic medium. Thus, diatomite and POSS cage structures can be potential reinforcements for nanocomposite design in hard tissue engineering applications.Article Citation - WoS: 69Citation - Scopus: 77Novel Zein-Based Multilayer Wound Dressing Membranes With Controlled Release of Gentamicin(John Wiley and Sons Inc., 2019) Kimna, Ceren; Tamburacı, Sedef; Tıhmınlıoğlu, FundaRecently, functional multilayer scaffolds with controlled drug release ability come into prominence for wound healing applications to mimic the layered structure of skin tissue and prevent the possible infections at the defect site. In this study, controlled antibiotic releasing zein bilayer membranes were fabricated for treatment of acute skin infections. Gentamicin loaded fibers were prepared by electrospinning on the membrane surface. Membranes were characterized with scanning electron microscope, atomic force microscopy, Fourier transform infrared spectroscopy, contact angle, mechanical analysis, swelling, degradation, and water vapor permeability studies. In vitro cytotoxicity, cell attachment, and proliferation were investigated. Cell attachment on fiber layer was observed with fluorescence imaging. Fabricated fibers showed structural similarity to the skin tissue layers with a fiber diameter range of 350-425 nm and film thickness in the range of 311-361 mu m. Mechanical properties were found compatible with the skin tissue. In addition, membranes showed antimicrobial activity against Staphylococcus aureus and Escherichia coli. The sustained release was achieved with a cumulative release of 94%. Membranes did not show any cytotoxic effect. NIH/3T3 and HS2 cell lines were proliferated on each layer mimicking the multilayer skin tissue. Hence, zein-based bilayer membrane showed promising properties to be used as a potential antimicrobial wound dressing for skin tissue regeneration. (c) 2018 Wiley Periodicals, Inc.Article Citation - WoS: 28Citation - Scopus: 29Development of a High-Flux Thin-Film Composite Nanofiltration Membrane With Sub-Nanometer Selectivity Using a Ph and Temperature-Responsive Pentablock Co-Polymer(American Chemical Society, 2019) Bar, Canbike; Çağlar, Nagahan; Uz, Metin; Mallapragada, Surya K.; Alsoy Altınkaya, SacideProducing block co-polymer-based nanofiltration (NF) membranes with sharp molecular weight cutoffs via an efficient method exhibiting persistent size-based separation quality is challenging. In this study, this challenge was addressed by reporting a facile approach to fabricate pentablock co-polymer (PBC)-based thin-film composite (TFC) NF membranes. The PBC, consisting of temperature-responsive Pluronic F127 (PEO-b-PPO-b-PEO) middle blocks and pH-responsive poly(N,N-(diethylamino)ethyl methacrylate) end blocks, were synthesized by atom-transfer radical polymerization. This polymer was then attached electrostatically to the surface of polysulfone/sulfonated polyether-sulfone support membranes fabricated using a non-solvent-induced phase separation technique. The conformational changes of the PBC chains in response to pH and temperature determined the, pure water flux and neutral solute (PEG 1000) rejection performance of TFC membranes. Permeability of the membranes increased from 13.0 +/- 0.63 to 15.9 +/- 0.06 L/m(2).h bar and from 6.7 +/- 0.00 to 13.9 +/- 0.07 L/m(2).h.bar by changing the solution pH from 4 to 8.5 and temperature from 4 to 25 degrees C, respectively. The pH- and temperature-responsive conformational changes did not affect the PEG 1000 rejection and membrane pore radius, which remained constant at similar to 89% and similar to 0.9 nm, respectively. This important finding was attributed to the high grafting density of co-polymer chains, resulting in spatial limitations among the grafted chains. The pore size of similar to 0.9 nm achieved with the proposed membrane design is the smallest size reported so far for membranes fabricated from block copolymers. TFC membranes demonstrated high stability and maintained their flux and rejection values under both static (storage in an acidic solution for up to 1 month) and dynamic (filtering PEG 1000 solution over 1 week) conditions. Pentablock copolymers enable a NF membrane with a sharp molecular weight cutoff suitable for size-selective separations. The membrane fabrication technique proposed in this study is a scalable and promising alternative that does not involve complex synthetic routes.Article Citation - WoS: 22Citation - Scopus: 25Novel Hybrid Treatments of Textile Wastewater by Membrane Oxidation Reactor: Performance Investigations, Optimizations and Efficiency Comparisons(Elsevier, 2019) Aydıner, Coşkun; Mert, Berna Kiril; Doğan, Esra Can; Yatmaz, Hüseyin Cengiz; Dağlı, Sönmez; Aksu, Şeyda; Gören, Ayşegül Yağmur; Balcı, EsinFeasible reclamation of industrial wastewaters by consuming less resource and time requires researchers to develop advanced and sophisticated solutions to meet today's versatile needs. In this respect, novel technological applications of hybrid membrane oxidation reactor (MOR) comprising of the Fenton or photo-Fenton enhanced ultrafiltration (FEUF and pFEUF), was demonstrated for treating textile washing wastewater. Their comparative hybrid performances were explored based on response surface analyses of Taguchi experimental designs that were optimized for maximized responses at minimum oxidant and acid consumptions. From eleven specific variables, those affecting the hybrid treatment performances at significant levels were found as H2O2 amount, process time, membrane type, Fe2+ concentration and temperature. The pFEUF treatment showed better and faster organics removal efficiency than by FEUF, and the UF process was seen to be more affected from changing operational conditions in pFEUF. Organic pollutants were oxidized by 56.6 +/- 8.7% degradation and 31.5 +/- 3.2% mineralization, while UF allowed a synergistic contribution to the hybrid MOR performance by 38.1 +/- 4.7% and 17.3 +/- 3.1%, respectively. Compared to simultaneous MOR and external UF after Fenton, sequential MOR was found as the best solution by an efficiency of 84.5% COD, 70.5% TOC, and 155.6 L/m(2).h. The effluents could be readily produced with quality suitable for directly discharging to the sewage infrastructure system resulting in a complete treatment. This study proved that the developed MOR techniques are technologically favorable for the treatment of industrial organic wastewaters due to high treatment performances and less resource, time and land needs. It can be finally declared that they can be used as rather attractive solutions for not only wastewater reclamation but also water recovery by further handling of their effluents. (C) 2019 Elsevier B.V. All rights reserved.Article Citation - WoS: 20Citation - Scopus: 24In Vitro Evaluation of Microleakage and Microhardness of Ethanolic Extracts of Propolis in Different Proportions Added To Glass Ionomer Cement(Journal of Clinical Pediatric Dentistry, 2016) Altunsoy, Mustafa; Tanrıver, Mehmet; Turkan, Uğur; Uslu, Mehmet Emin; Silici, SibelObjective: To evaluate the effect of ethanolic extracts of propolis (EEP) addition in different proportions to glass ionomer cement (GIC) on microleakage and microhardness of GIC. Study design: The cement was divided into four groups: one using the original composition and three with 10%, 25%, and 50% EEP added to the liquid and then manipulated. For microleakage assessment, sixty primary molars were randomly divided into four groups (n=15). Standard Class II cavities were prepared and then filled with EEP in different proportions added to GICs. Microleakage test was performed using a dye penetration method The data were analyzed using one-way ANOVA and Mann - Whitney U tests (alpha = 0.05). Disc shaped specimens were prepared from the tested GIC to determine Vickers hardness (VHN). The data were analyzed using one-way ANOVA and post hoc Tukey test (alpha = 0.05). Results: There were no statistically significant differences between the groups in terms of microleakage (p > 0.05). There were statistically signcant differences between the VHN values of groups (p < 0.05). Increasing addition of EEP to GIC statistically significantly increased VHN value of GIC (p < 0.05). Conclusions: The addition of EEP to GIC increased the microhardness of the GIC and did not adversely affect the microleakage. Thus, it might be used during routine dental practice due to its antibacterial propertiesArticle Citation - WoS: 26Citation - Scopus: 28Osteoconductive 3d Porous Composite Scaffold From Regenerated Cellulose and Cuttlebone-Derived Hydroxyapatite(SAGE Publications Inc., 2019) Palaveniene, Alisa; Tamburacı, Sedef; Kimna, Ceren; Glambaite, Kristina; Baniukaitiene, Odeta; Tıhmınlıoğlu, Funda; Liesiene, JolantaRecently, usage of marine-derived materials in biomedical field has come into prominence due to their promising characteristics such as biocompatibility, low immunogenicity and wide accessibility. Among these marine sources, cuttlebone has been used as a valuable component with its trace elemental composition in traditional medicine. Recent studies have focused on the use of cuttlebone as a bioactive agent for tissue engineering applications. In this study, hydroxyapatite particles were obtained by hydrothermal synthesis of cuttlebone and incorporated to cellulose scaffolds to fabricate an osteoconductive composite scaffold for bone regeneration. Elemental analysis of raw cuttlebone material from different coastal zones and cuttlebone-derived HAp showed that various macro-, micro- and trace elements - Ca, P, Na, Mg, Cu, Sr, Cl, K, S, Br, Fe and Zn were found in a very similar amount. Moreover, biologically unfavorable heavy metals, such as Ag, Cd, Pb or V, were not detected in any cuttlebone specimen. Carbonated hydroxyapatite particle was further synthesized from cuttlebone microparticles via hydrothermal treatment and used as a mineral filler for the preparation of cellulose-based composite scaffolds. Interconnected highly porous structure of the scaffolds was confirmed by micro-computed tomography. The mean pore size of the scaffolds was 510 mu m with a porosity of 85%. The scaffolds were mechanically characterized with a compression test and cuttlebone-derived HAp incorporation enhanced the mechanical properties of cellulose scaffolds. In vitro cell culture studies indicated that MG-63 cells proliferated well on scaffolds. In addition, cuttlebone-derived hydroxyapatite significantly induced the ALP activity and osteocalcin secretion. Besides, HAp incorporation increased the surface mineralization which is the major step for bone tissue regeneration.Article Citation - WoS: 24Citation - Scopus: 26Self-Assembly Behavior of the Keratose Proteins Extracted From Oxidized Ovis Aries Wool Fibers(Elsevier Ltd., 2019) Pakkaner, Efecan; Yalçın, Damla; Uysal, Berk; Top, AybenWater soluble keratose proteins were obtained from an Ovis Aries wool using peracetic acid oxidation. The wool samples and the extracted keratose proteins were characterized by using FTIR, XRD, SEM and TGA techniques. Fractions of alpha-keratose (MW = 43-53 kDa) along with protein species with molecular weights between 23 kDa and 33 kDa were identified in the SDS-PAGE analysis result of the extracted protein mixture. DLS and AFM experiments indicated that self-assembled globular nanoparticles with diameters between 15 nm and 100 nm formed at 5 mg/ml keratose concentration. On the other hand, upon incubation of 10 w % keratose solutions at 37 degrees C and 50 degrees C, interconnected keratose hydrogels with respective storage modulus (G') values of 0.17 +/- 0.03 kPa and 3.7 +/- 0.5 kPa were obtained. It was shown that the keratose hydrogel prepared at 37 degrees C supported L929 mouse fibroblast cell proliferation which suggested that these keratose hydrogels could be promising candidates in soft tissue engineering applications. (C) 2018 Elsevier B.V. All rights reserved.