Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
61 results
Search Results
Article Citation - WoS: 6Citation - Scopus: 4Regenerable Nickel Catalysts Strengthened Against H2s Poisoning in Dry Reforming of Methane(Elsevier, 2025) Kesan Celik, Nazli; Yasyerli, Sena; Arbag, Huseyin; Tasdemir, H. Mehmet; Yasyerli, NailIn this study, alumina-supported bimetallic Ni-Cu and trimetallic Ni-Cu-Ce catalysts were synthesized to improve catalysts resistant to coke formation and sulfur poisoning for dry reforming of methane (DRM). The effects of parameters such as feed composition, synthesis method, and H2S concentration using the catalyst with the best activity were also investigated. To determine the physical and chemical properties of the synthesized catalysts, XRD, N2 adsorption-desorption, TGA-DTA, ICP-OES, SEM-EDX, XPS, and DRIFTS analyses were performed. XRD analysis showed that the fresh Ni-Cu catalysts have elemental nickel and gamma- alumina phases in their structures. In addition to these structures, the CeO2 crystal structure was determined for the Ni-Cu-Ce catalyst. Type IV isotherm with H1 hysteresis indicating uniform mesoporous structure was obtained with all the catalysts. The activities of the synthesized catalysts in DRM were performed in the presence of different concentrations of H2S (2 ppm, 50 ppm, and 500 ppm) in a fixed bed reactor at 750 degrees C using a gas chromatography-equipped system. The alumina-supported 8Ni-3Cu-8Ce catalyst prepared by the impregnation method exhibited a higher and more stable activity comparing the bimetallic Ni-Cu catalyst in the presence of H2S. Adding copper and cerium to the nickel catalyst has a curative effect on resistance to coke formation and sulfur poisoning. Excess CO2 in the feed stream increased the H2S poisoning resistance of the catalyst. To analyze the reactor exit stream in catalytic activity using different feed stream compositions such as H2S+He, H2S+CO2+He, and H2S+CO2+CH4+He, FTIR with a gas cell was used. The formation of carbonyl sulfide (COS) and H2O, which occurs due to the possible reaction between CO2 and H2S, was observed. Regeneration studies showed that the catalyst could undergo regeneration with a low oxygen concentration (0.3 % O2 in He). 8Ni-3Cu-8Ce@SGA, which gave 71 % CH4 conversion in the first minute of the reaction test in the presence of 50 ppm H2S, was regenerated after completely losing its activity at the end of 5 h. 66 % CH4 conversion was achieved when tested again in the absence of H2S (CH4/CO2/Ar:1/1/1). The 8Ni-3Cu-8Ce@SGA catalyst was deemed worthy of investigation for industrial applications.Book Part Advances in Nanocomposite Membranes for CO2 Removal(Elsevier, 2024) Marpani,F.; Othman,N.H.; Alias,N.H.; Mat Shayuti,M.S.; Alsoy Altınkaya, SacideNanocomposite membranes have emerged as a promising solution for efficient carbon dioxide (CO2) removal in gas separation processes. These membranes combine polymeric matrices with inorganic nanofillers to synergize the excellent separation performance of inorganic materials with the mechanical stability of polymers. The choice of nanofillers, such as porous and nonporous materials, significantly influences the gas permeability and selectivity of the resulting nanocomposite membranes. Porous fillers with interstitial channels and large surface areas are found to selectively adsorb CO2, enhancing membrane separation performance. On the other hand, nonporous fillers alter the polymer chain orientation, influencing gas separation differently. The 1D, 2D, and 3D morphologies of nanofillers offer unique properties in terms of surface-to-volume ratio, permeability, and selectivity. The fabrication of nanocomposite membranes also plays a crucial role, and advances in materials and manufacturing techniques have enabled the design of high-performing membranes. Asymmetric and symmetric configurations have been explored to optimize separation efficiency. Nevertheless, challenges such as aging, compaction, and swelling need to be addressed to ensure the long-term stability of nanocomposite membranes. Future research should focus on developing advanced theoretical models to better predict gas permeation behaviors in these membranes. Overall, nanocomposite membranes offer a promising avenue for efficient CO2 removal, contributing to sustainable environmental practices and energy production. © 2024 Elsevier Ltd. All rights reserved.Conference Object Citation - WoS: 1Citation - Scopus: 1A Mixed-Integer Dynamic and Stochastic Algae Process Optimization(Elsevier, 2024) Kivanc, Sercan; Deliismail, Özgün; Şıldır, HasanWith increased energy demand as it gets scarcer, a great deal of research is being carried out into alternatives to non - renewable energy resources. One of the promising studies is the biofuel production from micro algae. Microalgae are photosynthetic organisms and capture carbon dioxide, reducing emissions and providing valuable products (fuel, fertilizer, etc.). Thus, efficiency in the design and optimization of process related units are important. In this study, the optimal experimental conditions for Nannochloropsis Oculata were calculated under the constraints of the model equations and other process related constraints through simultaneous optimization approach. The economic evaluation of the process is also handled by introducing the uncertainty in the economic measures sampled from normal distribution to maximize the average profit. Unlike traditional approaches, the MINLP formulation, which is solved stochastically, dynamically, and simultaneously, provides more robust and reliable results, flexibility, improved decision making, reduced risks to be taken and a better understanding of risk factors. Copyright (C) 2024 The Authors. This is an open access article under the CC BY-NC-ND license (https://creativecommons.org/licenses/by-nc-nd/4.0/)Article Mini modular plant design for ethylene production using Martian atmosphere on Mars(Elsevier, 2024) Deliismail, Özgün; Şeker, ErolA main shift in the competitive landscape of technology development is in 3D printing of complex articles made of variety of materials due to faster manufacturing and less human error in the production. In fact, it seems to be a viable candidate for the construction of structures for terrestrial and extraterrestrial life in future. Thus, new or damaged equipment in space explorations could be replaced instantly, and habitats could be manufactured using 3D printing in varying gravitational fields in the solar system. Among 3D printing materials, HDPE is commonly used in the projects, such as a prototype manufacturing or pipes or damp-proof membrane. This study initially focused on the preliminary design of the self-sustaining mini ethylene production plant from Martian atmosphere with scale-out architecture. UniSIM® was integrated with MATLAB® via CAPE-OPEN extension to design mini-ethylene production plant at low gravity. Ethylene capacity was found as 17.71 tons/year for 100 modules. © 2023 COSPARArticle Simultaneous Topology Design and Optimization of Pde Constrained Processes Based on Mixed Integer Formulations(Elsevier, 2024) Ertürk, Emrullah; Deliismail, Özgün; Şıldır, HasanSimultaneous topological design and optimization of complex processes that are described by partial differential equations is a challenging but promising research area. Widely adopted nested and sequential approaches are mostly applicable based on heuristic solutions, hindering the theoretical improvement potential due to decentralized decision-making in subsequent stages with a significant number of trial-and-error procedures. This study introduces a mixed integer formulation addressing the governing equations and case-dependent topological constraints at each discretization point, enabling solutions through rigorous solvers under process-related constraints and objectives. Nonlinear expressions in the formulations are further tailored using piecewise linear approximations, still representing the major nonlinear trends through a mixed-integer linear nature to favor global optimality and benefit from computational advancements, when needed. Heat and Stokes flow problems are used as case studies to demonstrate the applicability of the methodology. © 2024 Elsevier B.V.Article Citation - WoS: 4Citation - Scopus: 5Breakthrough Curve Analysis of Phosphorylated Hazelnut Shell Waste in Column Operation for Continuous Harvesting of Lithium From Water(Elsevier, 2024) Recepoğlu, Yaşar Kemal; Arar, Ozguer; Yuksel, AsliIn batch-scale operations, biosorption employing phosphorylated hazelnut shell waste (FHS) revealed excellent lithium removal and recovery efficiency. Scaling up and implementing packed bed column systems necessitates further design and performance optimization. Lithium biosorption via FHS was investigated utilizing a continuous-flow packed-bed column operated under various flow rates and bed heights to remove Li to ultra-low levels and recover it. The Li biosorption capacity of the FHS column was unaffected by the bed height, however, when the flow rate was increased, the capacity of the FHS column decreased. The breakthrough time, exhaustion time, and uptake capacity of the column bed increased with increasing column bed height, whereas they decreased with increasing influent flow rate. At flow rates of 0.25, 0.5, and 1.0 mL/min, bed volumes (BVs, mL solution/mL biosorbent) at the breakthrough point were found to be 477, 369, and 347, respectively, with the required BVs for total saturation point of 941, 911, and 829, while the total capacity was calculated as 22.29, 20.07, and 17.69 mg Li/g sorbent. In the 1.0, 1.5, and 2.0 cm height columns filled with FHS, the breakthrough times were 282, 366, and 433 min, respectively, whereas the periods required for saturation were 781, 897, and 1033 min. The three conventional breakthrough models of the Thomas, Yoon-Nelson, and Modified Dose-Response (MDR) were used to properly estimate the whole breakthrough behavior of the FHS column and the characteristic model parameters. Li's extremely favorable separation utilizing FHS was evidenced by the steep S-shape of the breakthrough curves for both parameters flow rate and bed height. The reusability of FHS was demonstrated by operating the packed bed column in multi-cycle mode, with no appreciable loss in column performance.Article Citation - WoS: 6Citation - Scopus: 6Inverse Effects of Lanthanide Co-Doping on the Photocatalytic Hydrogen Production and Dye Degradation Activities of Cu Doped Sol-Gel Tio<sub>2</Sub>(Elsevier, 2023) Yurtsever, Husnu Arda; Erzin, Kubilay; Ciftcioglu, Muhsin; Yurtsever, Hüsnü Arda; Erzin, Kubilay; Çiftçioğlu, MuhsinCopper doped and lanthanide-copper co-doped titania powders were prepared by sol-gel technique and the effects of co-doping on the photocatalytic reduction and oxidation activities of titania were investigated in this work. Characterization studies indicated that a reduced structure was formed due to the presence of Ti3+ species in copper doped titania powder and a more stable structure was formed when lanthanides were used as co-dopants. Copper doped powder had a significantly higher activity in photocatalytic hydrogen production (1037 mu mol/g/h) than the co-doped powders (similar to 400 mu mol/g/h). The oxidation activities of co-doped powders however were determined to be about 2 times higher than that of the copper doped powder. The decrease in the reduction activity was attributed to the decrease in the number of Ti3+ sites, whereas the increase in oxidation activity was probably a result of the increase in the surface area and dye adsorption due to lanthanide co-doping.Book Part Citation - Scopus: 2Data Driven Leak Detection in a Real Heat Exchanger in an Oil Refinery(Elsevier, 2023) Yasmal, Aslı; Kuşoğlu Kaya, Gizem; Oktay, Emirhan; Çölmekci, Ceylan; Uzunlar, ErdalThis study focuses on implementation of a data-based leak detection method in a heat exchanger in a petroleum refinery. We have studied on the two real leakage cases in a heat exchanger in Izmit TUPRAS Refinery. Leaks are one of the major problems that occur in operations. The autoencoder (AE) method is implemented for leak detection. Reconstruction error is used as the leak indicator. In case of leakage, the reconstruction value is expected to increase. For both cases examined, the reconstruction error is found to be around 1-5 under normal operating conditions. On the other hand, reconstruction error is observed to change between 10 and 60 under the conditions with leakage. Besides, the AE is able to indicate the start of one leakage case before the process engineers noticed it. © 2023 Elsevier B.V.Article Citation - WoS: 2Citation - Scopus: 3A Phenomenological Kinetic Flotation Model: Distinct Time-Variant Floatability Distributions for the Pulp and Froth Materials(Elsevier, 2023) Polat, Mehmet; Polat, HürriyetA simple and easy-to-use phenomenological kinetic flotation model, strongly connected with the physics of the process, is proposed in this paper. The model explicitly contains the cell volume, aeration rate, volumetric holdup, mean bubble size, and particle density as input variables. It can be employed to characterize the floatability distributions of the particles in the pulp and the froth separately any time during the flotation process. Two new time-dependent kinetic parameters, the bubble loading factor & phi;(t) and the maximum cell mass transfer capacity Mmax(t) also appear in the model expression. & phi;(t) is a measure of the degree of crowding of the bubble surfaces and accounts for the deviations from the first-order rate equation. Mmax(t) describes the maximum amount of mass that can be transported to the froth phase by the bubble population in the cell. Screen fractionation of each froth product collected at different time intervals during a single kinetic flotation test is sufficient to generate the data required by the model for analysis. Application of the model to this data yields directly time-dependent functions for the floatability of the particles reporting to froth Kf(t) or remaining in the cell Kp(t) for each size fraction separately, without the need for any empirical parameters. The test of the model was carried out using published kinetic flotation data from the literature.Article Citation - WoS: 6Citation - Scopus: 9The Effect of Military Conflict Zone in the Middle East on Atmospheric Persistent Organic Pollutant Contamination in Its North(Elsevier, 2023) Ayrı, İlknur; Genişoğlu, Mesut; Sofuoğlu, Aysun; Kurt Karakuş, Perihan B.; Birgül, Askın; Sofuoğlu, Sait CemilThis study aimed to investigate long-range atmospheric transport of selected POPs released due to the effects of mili-tary conflicts in regions to the south of Turkey's borders. Ten locations were selected to deploy passive air samplers at varying distances to the border on a southeast-west transect of the country, proximity-grouped as close, middle, and far. Sampling campaign included winter and transition months when desert dust transport events occur. Hypothesis of the study was that a decreasing trend would be observed with increasing distance to the border. Group comparisons based on statistical testing showed that PBDE-183, E45PCB, and dieldrin in winter; PBDE-28, PBDE-99, PBDE-154, p,p '-DDE, E14PBDE, and E25OCP in the transition period; and PBDE-28, PBDE-85, PBDE-99, PBDE-154, PBDE-190, PCB-52, E45PCB, p,p '-DDE, and E25OCP over the whole campaign had a decreasing trend on the transect. An analysis of concen-tration ratio to the background showed that long-range atmospheric transport impacted the study sites, especially those of close group in comparison to the local sources. Back-trajectory analyses indicated that there was transport from the conflict areas to sites in the close-proximity group, while farther sampling locations mostly received air masses from Europe, Russia, and former Soviet Union countries, followed by North Africa, rather than the military con-flict areas. In consequence, decrease in concentrations with distance and its relation to molecular weight through pro-portions, diagnostic ratios, analysis of concentration ratio to the background, and back-trajectory analyses support the effect of transport from the military-conflict area to its north.