Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
4 results
Search Results
Article Citation - WoS: 1Citation - Scopus: 1Inhibition of Caco3 Growth and Synthesis of Submicron Particles by Preferential Adsorption of Additive Ca2+ Ions on Fresh Precipitates(Royal Society of Chemistry, 2022) Majekodunmi, Olukayode T.; Kılıç Özdemir, Sevgi; Özdemir, EkremThis study demonstrates a method to inhibit the growth of CaCO3 and synthesize submicron particles in a chemical precipitation process under ambient and high supersaturation conditions. Equimolar CaCl2 and Na2CO3 solutions were mixed in a model tubular reactor at a constant flow rate, and the precipitates were continuously dispersed in stirred 250 mL of 10 mM Ca(OH)2 solution. This approach resulted in the synthesis of colloidally stable submicron CaCO3 particles for a precipitant concentration ≤75 mM. Varying the precipitates’ retention time in the tubular reactor had no significant effects on the particle size and colloidal stability. Time-dependent changes in the mean size, crystal form, morphology and specific surface area of the synthesized particles were also studied. For a precipitant concentration of 75 mM, the particles were monodispersed and porous spindle-like scalenohedral crystals which gradually grew in all faces as more precipitates were fed into the Ca(OH)2 solution. The mean hydrodynamic size of the particles was ∼850 nm at the 8th minute. However, in the absence of additive Ca2+ ions, the particles obtained at the 8th minute were polydisperse mixtures of vaterite and rhombohedral calcite particles greater than 4 μm in size. The results show that free additive Ca2+ ions are irreversibly adsorbed onto the particles as the precipitates dissolve and recrystallize into smaller crystals upon reaching the Ca(OH)2 solution.Article Citation - WoS: 15Citation - Scopus: 18Preparation and Characterization of Magnesium Stearate, Cobalt Stearate, and Copper Stearate and Their Effects on Poly(vinyl Chloride) Dehydrochlorination(John Wiley and Sons Inc., 2015) Gönen, Mehmet; Egbuchunam, Theresa Obuajulu; Balköse, Devrim; İnal, Fikret; Ülkü, SemraPreparation and characterization of pure metal soaps and investigation of their effects on poly(vinyl chloride) (PVC) dehydrochlorination were the objectives of the present study. Magnesium stearate (MgSt2), cobalt stearate (CoSt2), and copper stearate (CuSt2) were prepared by a precipitation method. An aqueous sodium stearate (NaSt) solution was mixed at 500 rpm with respective metal salt solutions at 75oC. The precipitates that formed were collected by filtration, washed with water, and ultimately dried at 105oC under reduced pressure. Lamellar crystals that melted on heating were obtained. Solid-liquid phase transitions were observed by optical microscopy at 160oC, 159oC, and 117oC for MgSt2, CoSt2, and CuSt2, respectively. However, the melting points of MgSt2, CoSt2, and CuSt2 were determined as 115oC, 159oC, and 111oC, respectively, by analysis by differential scanning calorimetry. The onset temperature of the mass loss was the lowest at 255oC for CuSt2 and the lowest activation energy for thermal decomposition was 18 kJ/mol for CuSt2. CoSt2 was effective in extending the induction time of PVC dehydrochlorination at both 140oC and 160oC. The activation energy calculated from stability time decreased from 175 kJ/mol for a blank PVC sample to 114, 105, and 107 kJ/mol for MgSt2, CoSt2, and CuSt2-containing PVC samples, respectively. All three metal soaps accelerated the dehydrochlorination of PVC. J. VINYL ADDIT. TECHNOL., 21:235-244, 2015.Article Citation - WoS: 5Citation - Scopus: 5Methylene Blue Adsorption From Aqueous Solutions To Flexible Poly(vinyl Chloride) Silica Composites(John Wiley and Sons Inc., 2015) Yetgin, Senem; Ulutan, Sevgi; Balköse, DevrimMethylene blue (MB) adsorption studies were performed with poly(vinyl chloride)-(dioctyl phthalate)-silica composites, which were obtained by using plastisol-plastigel technology. The films were flexible, having elastic modulus of 1.0-1.5 GPa. Diminishing MB concentration in the aqueous phase was followed as the adsorption process advanced by using visible spectroscopy. Contributions of the individual components of the composites to adsorption were also investigated. Although the MB adsorption capacity was extensively high for silica, it was moderate for the composite, most likely owing to the occlusion of pores of silica by plasticizer to some extent. The improvement of MB adsorption capacity of the composites as the silica ratio increased was explicitly deduced from the optical microscopy photographs. The diffusion coefficients of MB through the composites were 5 × 10-13, 6 × 10-13, and 3 × 10-13 m2 s-1 with regression coefficients of 0.73, 0.89, and 0.88 for 0, 2, and 16% silica-containing composites, respectively. Because of the slow diffusion of MB in poly(vinyl chloride)-silica composites, using them as dynamic column adsorbent was not practical. However, these versatile plastics can be used as plastic labels, colored clothing, leather substitutes, antimicrobial medical devices, and laser printable surfaces.Article Citation - WoS: 6Citation - Scopus: 7Preparation and Characterization of Flexible Poly(vinyl Chloride) Foam Films(John Wiley and Sons Inc., 2012) Şahin, Erdem; Yaşar Mahlıçlı, Filiz; Yetgin, Senem; Balköse, DevrimIn this study, the effect of activator ZnO and heating time at 190°C on foaming, gelation, and dehydrochlorination of poly(vinyl chloride) (PVC) plastisol was investigated. For this purpose, a PVC plastisol was prepared by mixing PVC, dioctyl phthalate (DOP), azodicarbonamide (ADC), ZnO, and the heat stabilizers calcium stearate (CaSt 2) and zinc stearate(ZnSt 2). PVC plastisol films were heated for 3, 6, 12, and 24 min periods at 190°C to see the effect of heating time on the gelation and foaming processes of the PVC foam. The time of 12 min was determined to be optimum for the completion of gelation and foaming processes without thermal degradation of PVC. No foaming was observed under the same conditions for the samples without ZnO. ZnO had a significant catalytic effect on ADC decomposition, accelerating the foaming of the films. Average porosity measurement showed a consistent increase in porosity with heating time up to 76% and the average density decreased from 1.17 to 0.29 g/cm 3 on foaming. Tensile tests showed that the tensile strength and tensile strain both increased considerably up to 0.98 MPa and 207%, respectively, with heating time and the elastic modulus was seen to gradually decrease from 4.7 to 0.7 MPa with heating time. Films without ZnO had higher tensile strength since there were no pores. PVC thermomat tests showed that ZnO lowered the stability time of plastigel film with azodicarbonamide.