Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
10 results
Search Results
Article Citation - WoS: 23Citation - Scopus: 25Microcalorimetric Investigation of Water Vapor Adsorption on Silica Gel(Springer Verlag, 2011) Demir, Hasan; Mobedi, Moghtada; Ülkü, SemraWater vapor adsorption on silica gel was investigated using Tian-Calvet-type microcalorimetry. Differential heat of adsorption data was obtained. The setup of microcalorimetry was used volumetric system to determine adsorption isotherms of water vapor-silica gel. The Langmuir model was used in the interpretation of the adsorption data. The Clausius-Clapeyron diagram was also given. Effective mass diffusivity of water vapor in the silica gel particle as a function of temperature was also determined. The silica gel, which was degassed under vacuum at 10 -7 mbar and 120 °C for 18 h, was found to adsorb 0.6, 0.98, 1.1, 1.4, 2, 3.5, 11, 13, and 14 wt% water vapor at 120, 110, 100, 90, 75, 60, 40, 35, and 30 °C, respectively. The diffusivities of water vapor inside the silica gel for short- and long-range periods were described using kinetics data as a function of temperature in the Arrhenius form.Article Citation - WoS: 3Citation - Scopus: 3Heat and Mass Transfer in the Adsorbent Bed of an Adsorption Heat Pump(Taylor and Francis Ltd., 2011) Demir, Hasan; Mobedi, Moghtada; Ülkü, SemraThe heat and mass transfer equations governing an adsorbent bed in an adsorption heat p mp and the mass balance equation for the adsorbent particles in the adsorbent bed were solved numerically to simulate the cycle of a basic adsorption heat pump, which includes isobaric adsorption, isosteric heating, isobaric desorption, and isosteric cooling processes. The finite difference method was used to solve the set of governing equations, which are highly nonlinear and coupled. The pressures of the evaporator and condenser were 2 and 20 kPa, respectively, and the regeneration temperature of the bed was 403 K. Changes in the temperature, adsorptive pressure, and adsorbate concentration in the adsorbent bed at different steps of the cycle were determined. The basic simulated cycle is presented in a Clausius-Clapeyron diagram, which illustrates the changes in average pressure and temperature of the adsorbent bed throughout the cycle. The results of the simulation indicated that the most time-consuming processes in the adsorption heat pump cycle were isobaric adsorption and isobaric desorption. The high thermal resistance of the bed slows down heat transfer, prolonging adsorption and desorption processes.Article Citation - WoS: 62Citation - Scopus: 64Effects of Porosity on Heat and Mass Transfer in a Granular Adsorbent Bed(Elsevier Ltd., 2009) Demir, Hasan; Mobedi, Moghtada; Ülkü, SemraIn the present study, the mechanism of heat and mass transfer in an annulus adsorbent is handled. The heat and mass transfer equations for the adsorbent bed and the mass balance equation for the adsorbent granules are numerically solved to obtain the distributions of temperature, pressure, adsorptive density and adsorbate concentration in the adsorbent bed. The study is performed for the silica gel-water pair and for three different values of porosity as 0.1, 0.2 and 0.3. The distributions of temperature and adsorbate concentration are considerably influenced from the bed porosity. The adsorption period increases with the increase of the porosity value. The porosity affects the pressure and adsorptive density distributions at the beginning of the process and after a relatively short time, the averages of these dependent variables approach to the final equilibrium state.Article Citation - WoS: 51Citation - Scopus: 58Effect of Additives on Flexible Pvc Foam Formation(Elsevier Ltd., 2008) Demir, Hasan; Sipahioğlu, Muzaffer; Balköse, Devrim; Ülkü, SemraIn this study, effects of Ca/Zn stearate and organotin heat stabilizers and zeolite, CaCO3, cellulose and luffa flours fillers, and their concentrations (2.5, 5, 10 and 20% by weight) on production of flexible PVC foams by chemical blowing agent, azodicarbonamide were investigated. Foam morphology, foam density, compressive mechanical properties and water uptake capacities of samples were determined. Morphology of the sample without any filler showed that employment of Ca stearate and Zn stearate heat stabilizers instead of organotin stabilizers increases foam formation and decreases pore sizes and regularity in pore size distribution. Foams having organotin stabilizer were more resistant to heat than the ones with Ca/Zn stearate for long heating periods. Foams, including organotin-based heat stabilizers, have compact structure. It was observed that, samples containing zeolite, CaCO3, cellulose or luffa flour had lower pore volume but higher Young's modulus and stress values compared to unfilled samples.Article Citation - WoS: 262Citation - Scopus: 286Dye Adsorption Behavior of Luffa Cylindrica Fibers(Elsevier Ltd., 2008) Demir, Hasan; Top, Ayben; Balköse, Devrim; Ülkü, SemraUsing natural Luffa cylindrica fibers as adsorbent removal of methylene blue dye from aqueous solutions at different temperatures and dye concentrations was investigated in this study. Thermodynamics and kinetics of adsorption were also investigated. The adsorption isotherms could be well defined with Langmuir model instead of Freundlich model. The thermodynamic parameters of methylene blue (MB) adsorption indicated that the adsorption is exothermic and spontaneous. The average MB adsorption capacity was found out as 49 mg/g and average BET surface area of fibers was calculated as 123 m2/g.Article Citation - WoS: 325Citation - Scopus: 366A Review on Adsorption Heat Pump: Problems and Solutions(Elsevier, 2008) Demir, Hasan; Mobedi, Moghtada; Ülkü, SemraAdsorption heat pumps have considerably sparked attentions in recent years. The present paper covers the working principle of adsorption heat pumps, recent studies on advanced cycles, developments in adsorbent-adsorbate pairs and design of adsorbent beds. The adsorbent-adsorbate pair features for in order to be employed in the adsorption heat pumps are described. The adsorption heat pumps are compared with the vapor compression and absorption heat pumps. The problems and troubles of adsorption heat pumps are classified and researches to overcome the difficulties are discussed.Article Citation - WoS: 324Citation - Scopus: 356The Effect of Fiber Surface Treatments on the Tensile and Water Sorption Properties of Polypropylene-Luffa Fiber Composites(Elsevier Ltd., 2006) Demir, Hasan; Atikler, Ulaş; Balköse, Devrim; Tıhmınlıoğlu, FundaThe effects of coupling agents on the mechanical, morphological, and water sorption properties of luffa fiber (LF)/polypropylene(PP) composites were studied. In order to enhance the interfacial interactions between the PP matrix and the luffa fiber, three different types of coupling agents, (3-aminopropyl)-triethoxysilane (AS), 3-(trimethoxysilyl)-1-propanethiol (MS), and maleic anhydride grafted polypropylene (MAPP) were used. The PP composites containing 2-15 wt% of LF were prepared in a torque rheometer. The tensile properties of the untreated and treated composites were determined as a function of filler loading. Tensile strength and Young's modulus increased with employment of the coupling agents accompanied by a decrease in water absorption with treatment due to the better adhesion between the fiber and the matrix. The maximum improvement in the mechanical properties was obtained for the MS treated LF composites. The interfacial interactions improved the filler compatibility, mechanical properties, and water resistance of composites. The improvement in the interfacial interaction was also confirmed by the Pukanszky model. Good agreement was obtained between experimental data and the model prediction. Morphological studies demonstrated that better adhesion between the fiber and the matrix was achieved especially for the MS and AS treated LF composites. Atomic force microscope (AFM) studies also showed that the surface roughness of LFs decreased with the employment of silane-coupling agents.Article Citation - WoS: 71Citation - Scopus: 87Influence of Surface Modification of Fillers and Polymer on Flammability and Tensile Behaviour of Polypropylene-Composites(Elsevier Ltd., 2006) Demir, Hasan; Balköse, Devrim; Ülkü, SemraAn intumescent system consisting of ammonium polyphosphate (APP) as an acid source and blowing agent, pentaerythritol (PER) as a carbonific agent and natural zeolite (clinoptilolite, Gördes II) as a synergistic agent was used in this study to enhance flame retardancy of polypropylene (FR-PP). Zeolite was incorporated into flame retardant formulation at four different concentrations (1, 2, 5, and 10 wt%) to investigate synergism with the flame retardant materials. Filler content was fixed at 30 wt% of total amounts of flame retardant PP composites. Zeolite and APP were treated with two different coupling agents namely, 3-(trimethoxysilyl)-1-propanethiol and (3-aminopropyl)-triethoxysilane for investigation of the influence of surface treatments on mechanical properties and flame retardant performance of composites. Maleic anhydride grafted polypropylene (MAPP) was used for making polypropylene hydrophilic. Flammability of FR-PP composites was measured by the determination of limiting oxygen index (LOI). The LOI values reached to a maximum value of 41% for mercapto silane treated APP:PER (2:1) PP composite containing 5 wt% zeolite. The tensile strength of composites was increased by the addition of MAPP and elongation at break of composites was increased with silane treatments.Article Citation - WoS: 35Citation - Scopus: 39Optimisation of the Effect of Colemanite as a New Synergistic Agent in an Intumescent System(Elsevier Ltd., 2006) Atikler, Ulaş; Demir, Hasan; Tokatlı, Figen; Tıhmınlıoğlu, Funda; Balköse, Devrim; Ülkü, SemraAn intumescent system including ammonium polyphosphate (APP) as an acid source and blowing agent, pentaerythritol (PER) as a carbonific agent and colemanite as a synergistic agent is used to enhance flame retardancy of polypropylene (FR-PP). In order to investigate the synergism between colemanite and the flame retardant materials (APP and PER), D-optimal mixture design was employed. The limiting oxygen index (LOI) and amount of residue (AoR) were accepted as response 1 and response 2, respectively. Applying D-optimal strategy, 18 experiments were performed. Filler content was fixed at 30 wt% of total amounts of flame retardant PP composites. Constraints were determined according to the ratio of APP/PER ranging between 1 and 3. Statistical analysis of the cubic model revealed that lack of fit (LoF) was not significant for the cubic and linear model for both responses. The model suggested an optimum composite formulation with concentration levels 65% of APP, 28% of PER and 7% of colemanite that gives an LOI of 40.3. The experimental LOI and AoR of optimum formulation were achieved as 39.3 and 21.4 with 2.5% and 2.2% errors, respectively.Article Citation - WoS: 187Citation - Scopus: 208Synergistic Effect of Natural Zeolites on Flame Retardant Additives(Elsevier Ltd., 2005) Demir, Hasan; Arkış, Esen; Balköse, Devrim; Ülkü, SemraThe thermal degradation and flammability of intumescent fire-retardant polypropylene matrix composites consisting of ammonium polyphosphate (APP) as an acid source and blowing agent, pentaerythritol (PER) as a carbonisation agent and natural zeolite (clinoptilolite rich, Gördes II) as a synergistic agent were examined. APP and PER combinations were examined at different ratios (0.25, 0.33, 0.5, 1, 2, 3, and 4) for optimisation of the formulation for flame retardancy. The zeolite was incorporated into flame retardant formulation at four different concentrations (1, 2, 5, and 10 wt%) to investigate the synergism between the flame retardant materials. The thermal degradation and flammability of composites were characterized by thermogravimetric analysis (TGA) and by limiting oxygen index (LOI) measurement and horizontal burning (HB) tests. A synergistic effect in flame retardancy was observed when natural zeolites were used in combination with APP and PER.