Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
4 results
Search Results
Article Citation - WoS: 2Citation - Scopus: 2Morphology of Sodium Salt of Calf Thymus Dna on Mica, Alumina, and Silica Surfaces: Effect of Solvent and Drying Method(Taylor and Francis Ltd., 2017) Yetgin, Senem; Balköse, DevrimInvestigation of morphology of deoxyribonucleotide triphosphate (DNA) dried on different surfaces by atomic force microscopy (AFM) is important in DNA research that is focused on subjects of condensation for gene therapy, sizing, DNA mapping, and cancer examination. The solvent, the surface type, and the method of drying effect the morphology of DNA on solid surfaces. Ethanol and water were used as solvents, flat mica, silica, and alumina surfaces were used as the substrates in the present study. Different methods such as ambient air-drying, N2-forced flow regime drying, and freeze-drying have been applied to droplets of DNA solutions in water or ethanol on the substrates. Forced flow drying regime causes nonlinear DNA attachment on the surface and self-assembly. DNA vertical distance on mica surface was found to be 6 and 1.4 nm for DNA dried in ambient air from ethanol and water solutions, respectively. It was 1.6 nm for N2 flow drying of aqueous DNA solution on mica surface. It was 4.6, 4.6, and 1.99 nm for ambient, N2 flow, and freeze-dried aqueous DNA on alumina surfaces, respectively. Aqueous solution of DNA dried under N2 flow on silica surface had 0.8 nm vertical distance. The smallest standard deviation of 0.05 nm was observed for DNA dried under N2 flow on alumina surface.Article Citation - WoS: 5Citation - Scopus: 5Determination of Electrostatic Potential Distribution by Atomic Force Microscopy (afm) on Model Silica and Alumina Surfaces in Aqueous Electrolyte Solutions(Elsevier Ltd., 2014) Yelken Özek, Gülnihal; Polat, MehmetAFM was employed as a physicochemical probe to determine the electrostatic potential distribution quantitatively on selected ideal oxide surfaces (quartz 0 0 0 1 and sapphire 0 0 0 1) in aqueous media. The force of interaction between a silicon nitride tip and the oxide surface was measured at a given point under well-defined solution conditions. Relevant theories were used to isolate the electrostatic component from the total force of interaction which was then employed to estimate the surface potential at that point. Repeating the procedure on selected locations generated a potential map of the surface. Comparison of these potentials with those obtained from independent electrokinetic measurements confirmed the validity of the approach. © 2014 Elsevier B.V. All rights reserved.Conference Object Citation - Scopus: 3Characterization of Polysulfone Based Hemodialysis Membranes by Afm(Elsevier Ltd., 2012) Uz, Metin; Yaşar Mahlıçlı, Filiz; Polat, Mehmet; Alsoy Altınkaya, SacideMost of the hemodialysis membrane materials are hydrophobic in nature and allow protein adsorption on the surface easily due to hydrophobic interaction between membrane surface and protein molecules when in contact with blood. Adsorbed proteins can affect platelet and leukocyte adhesion, and modulate the response of plasmatic reactions followed by the activation of different defense systems in blood (Sun et al. 2003).Article Citation - WoS: 29Citation - Scopus: 32Visualization of the Equilibrium Fcc Catalyst Surface by Afm and Sem-Eds(Kluwer Academic Publishers, 2003) Bayraktar, Oğuz; Kugler, Edwin L.The deposition of metal contaminants (e.g., Ni, V, and Fe) from the hydrocarbon feed causes the deactivation of fluid catalytic cracking (FCC) catalyst used in petroleum refining. It is very important to understand the changes in the morphology and chemical composition on the catalyst surface and how these structural and chemical changes affect the catalyst performance. In this research, metal-contaminated FCC catalysts from a commercial unit have been characterized using AFM together with SEM-EDS. The AFM images showed the surface pores as well as the features that surround the pore's entrance on the catalyst surface. Catalyst surface contains debris that appear as bright spots in AFM images. SEM-EDS results have shown the presence of iron in these bright spots. Fe enrichment at the catalyst particle surface was also confirmed by XPS analyses.