Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
12 results
Search Results
Article Citation - WoS: 4Citation - Scopus: 5Breakthrough Curve Analysis of Phosphorylated Hazelnut Shell Waste in Column Operation for Continuous Harvesting of Lithium From Water(Elsevier, 2024) Recepoğlu, Yaşar Kemal; Arar, Ozguer; Yuksel, AsliIn batch-scale operations, biosorption employing phosphorylated hazelnut shell waste (FHS) revealed excellent lithium removal and recovery efficiency. Scaling up and implementing packed bed column systems necessitates further design and performance optimization. Lithium biosorption via FHS was investigated utilizing a continuous-flow packed-bed column operated under various flow rates and bed heights to remove Li to ultra-low levels and recover it. The Li biosorption capacity of the FHS column was unaffected by the bed height, however, when the flow rate was increased, the capacity of the FHS column decreased. The breakthrough time, exhaustion time, and uptake capacity of the column bed increased with increasing column bed height, whereas they decreased with increasing influent flow rate. At flow rates of 0.25, 0.5, and 1.0 mL/min, bed volumes (BVs, mL solution/mL biosorbent) at the breakthrough point were found to be 477, 369, and 347, respectively, with the required BVs for total saturation point of 941, 911, and 829, while the total capacity was calculated as 22.29, 20.07, and 17.69 mg Li/g sorbent. In the 1.0, 1.5, and 2.0 cm height columns filled with FHS, the breakthrough times were 282, 366, and 433 min, respectively, whereas the periods required for saturation were 781, 897, and 1033 min. The three conventional breakthrough models of the Thomas, Yoon-Nelson, and Modified Dose-Response (MDR) were used to properly estimate the whole breakthrough behavior of the FHS column and the characteristic model parameters. Li's extremely favorable separation utilizing FHS was evidenced by the steep S-shape of the breakthrough curves for both parameters flow rate and bed height. The reusability of FHS was demonstrated by operating the packed bed column in multi-cycle mode, with no appreciable loss in column performance.Article Citation - WoS: 6Citation - Scopus: 9The Effect of Military Conflict Zone in the Middle East on Atmospheric Persistent Organic Pollutant Contamination in Its North(Elsevier, 2023) Ayrı, İlknur; Genişoğlu, Mesut; Sofuoğlu, Aysun; Kurt Karakuş, Perihan B.; Birgül, Askın; Sofuoğlu, Sait CemilThis study aimed to investigate long-range atmospheric transport of selected POPs released due to the effects of mili-tary conflicts in regions to the south of Turkey's borders. Ten locations were selected to deploy passive air samplers at varying distances to the border on a southeast-west transect of the country, proximity-grouped as close, middle, and far. Sampling campaign included winter and transition months when desert dust transport events occur. Hypothesis of the study was that a decreasing trend would be observed with increasing distance to the border. Group comparisons based on statistical testing showed that PBDE-183, E45PCB, and dieldrin in winter; PBDE-28, PBDE-99, PBDE-154, p,p '-DDE, E14PBDE, and E25OCP in the transition period; and PBDE-28, PBDE-85, PBDE-99, PBDE-154, PBDE-190, PCB-52, E45PCB, p,p '-DDE, and E25OCP over the whole campaign had a decreasing trend on the transect. An analysis of concen-tration ratio to the background showed that long-range atmospheric transport impacted the study sites, especially those of close group in comparison to the local sources. Back-trajectory analyses indicated that there was transport from the conflict areas to sites in the close-proximity group, while farther sampling locations mostly received air masses from Europe, Russia, and former Soviet Union countries, followed by North Africa, rather than the military con-flict areas. In consequence, decrease in concentrations with distance and its relation to molecular weight through pro-portions, diagnostic ratios, analysis of concentration ratio to the background, and back-trajectory analyses support the effect of transport from the military-conflict area to its north.Article Citation - WoS: 9Citation - Scopus: 9Hollow Nano-caco3's Voc Sensing Properties: a Dft Calculation and Experimental Assessments(Elsevier, 2023) Bayram, Abdullah; Farzaneh, Amir; Esrafili, Mehdi D.; Okur, Salih; Özdemir, EkremAir is the most critical and necessary for life, and air quality significantly impacts people's health. Both indoor and outdoor pollution frequently contain volatile organic compounds (VOCs). Such contaminants provide immediate or long-term health risks to the living system. The present study investigates sorption characteristics of VOCs on hollow nano calcite (CaCO3) particles with 250 nm and 40 nm pore sizes to remove from the air ambient using the quartz crystal microbalance (QCM) technique at room temperature both experimentally and theoretically. The results were supported by density functional theory (DFT), and adsorption-desorption characteristics were studied with Langmuir adsorption isotherms. The QCM measurements showed a stable signal without having hysteresis, and the response of polar VOCs on hollow nano-CaCO3 particles such as ethanol, propanol, and humidity with higher polarity was less compared to solvents such as chloroform and dichloromethane, which revealed that the surfaces of CaCO3 particles have mostly non-polar properties. CaCO3 surface and VOC molecule interactions overlap with the Langmuir model. With DFT calculations, VOC and water molecule adsorption changes the CaCO3 Egap. Our findings show that the ΔEgap values increase as chloroform > dichloromethane > propanol > ethanol > water. This order suggests that the sensing response of the hollow CaCO3 structure is linearly proportional to the adsorption energies of VOC and water. The linear adsorption characteristics, high sensing response, and short recovery time illustrated that the newly synthesized nano-CaCO3 could be implemented as a new VOC adsorbent material for health, environmental sustainability, and in vitro microbiome cultures.Article Citation - WoS: 4Citation - Scopus: 5Continuous Treatment of Diethyl Hexyl and Dibutyl Phthalates by Fixed-Bed Reactor: Comparison of Two Esterase Bionanocomposites(Elsevier, 2022) Sanroman, Maria Angeles; Balcı, Esin; Rosales, Emilio; Pazos, Marta; Sofuoğlu, AysunThe removal of Diethyl hexyl phthalate (DEHP) and Dibutyl phthalate (DBP) is of great importance due to their potential adverse effects on the environment and human health. In this study, two bionanocomposites prepared by immobilization of Bacillus subtilis esterase by crosslinking to halloysite and supported in chitosan and alginate beads were studied and proposed as a green approach. The esterase immobilization was confirmed by physical-chemical characterization. Bionanocomposite using chitosan showed the best degradation levels in batch tests attaining complete degradation of DBP and around 90% of DEHP. To determine the operational stability and efficiency of the system, two fixed bed reactors filled with both bionanocomposites were carried out operating in continuous mode. Chitosan based bionanocomposite showed the best performance being able to completely remove DBP and more than 85% of DEHP at the different flowrates. These results proved the potential of these synthesized bionanocomposites to effectively remove Phthalic Acid Esters.Article Citation - WoS: 51Citation - Scopus: 583d Printed Gelatin/Decellularized Bone Composite Scaffolds for Bone Tissue Engineering: Fabrication, Characterization and Cytocompatibility Study(Elsevier, 2022) Kara, Aylin; Distler, Thomas; Polley, Christian; Schneidereit, Dominik; Seitz, Hermann; Friedrich, Oliver; Tıhmınlıoğlu, Funda; Boccaccini, Aldo RThree-dimensional (3D) printing technology enables the design of personalized scaffolds with tunable pore size and composition. Combining decellularization and 3D printing techniques provides the opportunity to fabricate scaffolds with high potential to mimic native tissue. The aim of this study is to produce novel decellularized bone extracellular matrix (dbECM)-reinforced composite-scaffold that can be used as a biomaterial for bone tissue engineering. Decellularized bone particles (dbPTs, ∼100 μm diameter) were obtained from rabbit femur and used as a reinforcement agent by mixing with gelatin (GEL) in different concentrations. 3D scaffolds were fabricated by using an extrusion-based bioprinter and crosslinking with microbial transglutaminase (mTG) enzyme, followed by freeze-drying to obtain porous structures. Fabricated 3D scaffolds were characterized morphologically, mechanically, and chemically. Furthermore, MC3T3-E1 mouse pre-osteoblast cells were seeded on the dbPTs reinforced GEL scaffolds (GEL/dbPTs) and cultured for 21 days to assess cytocompatibility and cell attachment. We demonstrate the 3D-printability of dbPTs-reinforced GEL hydrogels and the achievement of homogenous distribution of the dbPTs in the whole scaffold structure, as well as bioactivity and cytocompatibility of GEL/dbPTs scaffolds. It was shown that Young's modulus and degradation rate of scaffolds were enhanced with increasing dbPTs content. Multiphoton microscopy imaging displayed the interaction of cells with dbPTs, indicating attachment and proliferation of cells around the particles as well as into the GEL-particle hydrogels. Our results demonstrate that GEL/dbPTs hydrogel formulations have potential for bone tissue engineering.Article Citation - WoS: 7Citation - Scopus: 8Compositional, Microstructural and Mechanical Effects of Nacl Porogens in Brushite Cement Scaffolds(Elsevier, 2021) Şahin, Erdem; Çiftçioğlu, MuhsinModification of the setting process of brushite cements by varying the concentration of ions that alter calcium phosphate crystallization kinetics, is known to enable control on the monetite conversion extent and the accompanying microporosity. This is useful because monetite serves as a suitable matrix in macroporous scaffolds due to its higher phase stability and finer crystal morphology compared to its hydrous counterpart brushite. In this study the synergistic effect of NaCl and citric acid on the microstructural evolution of brushite cement was demonstrated and microporosity of macroporous monetite-rich cement blocks was minimized by a variable NaCl porogen size distribution approach. Initially, maximum packing ratio of various combinations of NaCl size groups in PEG were determined by their rheological analysis in a range between 57% and 69%. Statistical analysis revealed a positive correlation between the amounts of NaCl particles under 38 mu m and 212 mu m and the maximum packing ratio. Further broadening the size distributions of NaCl porogens with fine cement precursors was effective in increasing the solids packing ratio of cement blocks more than the maximum packing ratio for the porogens. This improvement in packing was accompanied by a reduction in microporosity despite the increase in micropore volume with ion induced monetite formation. The detrimental effect of the microporosity introduced to the structure during monetite formation was balanced for some size distributions and not so much for others, thereby resulting in a wide range of porosities and mechanical properties. Thus, the exponential dependence of mechanical properties on porosity and the mechanical properties of monetite-rich macroporous blocks at the theoretical zero-porosity were determined according to Rice's model. Zero-porosity extrapolations were much higher than those predicted for brushite cement, contrary to the common assumption that brushite is mechanically stronger than monetite.Article Citation - WoS: 52Citation - Scopus: 54Development of Si Doped Nano Hydroxyapatite Reinforced Bilayer Chitosan Nanocomposite Barrier Membranes for Guided Bone Regeneration(Elsevier, 2021) Tamburacı, Sedef; Tıhmınlıoğlu, FundaGuided Bone Regeneration (GBR) is a widely used process for the treatment of periodontal defects to prevent the formation of surrounding soft tissue at the periodontal defect and to provide hard tissue regeneration. Recently GBR designs have focused on the development of resorbable natural polymer-based barrier membranes due to their biodegradability and excellent biocompatibility. The aim of this study is to fabricate a novel bilayer nanocomposite membrane with microporous sublayer composed of chitosan and Si doped nanohydroxyapatite particles (Si-nHap) and chitosan/PEO nanofiber upper layer. Bilayer membrane was designed to prevent epithelial and fibroblastic cell migration and growth impeding bone formation with its upper layer and to support osteogenic cell bioactivity at the defect site with its sublayer. Microporous and nanofiber layers were fabricated by using freeze-drying and electrospinning techniques respectively. The effect of Si-nHap content on the morphological, mechanical and physical properties of the composites were investigated using SEM, AFM, micro-Ct, compression test, water uptake capacity and enzymatic degradation study. Antimicrobial properties of nanocomposite membranes were investigated with tube dilution and disk diffusion methods. In vitro cytotoxicity of bilayer membranes was evaluated. Saos-2 and NIH/3T3 proliferation studies were carried out on each layer. In vitro bioactivity of Saos-2 and NIH/3T3 cells were evaluated with ALP activity and hydroxyproline content respectively. Results showed that Si-nHap incorporation enhanced the mechanical and physical properties as well as controlling biodegradability of the polymer matrix. Besides, Si-nHap loading induced the bioactivity of Saos-2 cells by enhancing cell attachment, spreading and biomineralization on the material surface. Thus, results supported that designed bilayer nanocomposite membranes can be used as a potential biomaterial for guided bone regeneration in periodontal applications.Article Citation - WoS: 43Citation - Scopus: 47Bioactive Diatomite and Poss Silica Cage Reinforced Chitosan/Na-carboxymethyl Cellulose Polyelectrolyte Scaffolds for Hard Tissue Regeneration(Elsevier, 2019) Tamburacı, Sedef; Kimna, Ceren; Tıhmınlıoğlu, FundaRecently, natural polymers are reinforced with silica particles for hard tissue engineering applications to induce bone regeneration. In this study, as two novel bioactive agents, effects of diatomite and polyhedral oligomeric silsesquioxanes (POSS) on chitosan (CS)/Na-carboxymethylcellulose (Na-CMC) polymer blend scaffolds are examined. In addition, the effect of silica reinforcements was compared with Si-substituted nano-hydroxyapatite (Si-Hap) particles. The morphology, physical and chemical structures of the scaffolds were characterized with SEM, liquid displacement, FT-IR, mechanical analysis, swelling and degradation studies. The particle size and the crystal structure of diatomite, POSS and Si-Hap particles were determined with DLS and XRD analyses. In vitro studies were performed to figure out the cytotoxicity, proliferation, ALP activity, osteocalcin production and biomineralization to demonstrate the promising use of natural silica particles in bone regeneration. Freeze-dried scaffolds showed 190-307 mu m pore size range and 61-70% porosity. Both inorganic reinforcements increased the mechanical strength, enhanced the water uptake capacity and fastened the degradation rate. The nanocomposite scaffolds did not show any cytotoxic effect and enhanced the surface mineralization in osteogenic medium. Thus, diatomite and POSS cage structures can be potential reinforcements for nanocomposite design in hard tissue engineering applications.Article Citation - WoS: 22Citation - Scopus: 25Novel Hybrid Treatments of Textile Wastewater by Membrane Oxidation Reactor: Performance Investigations, Optimizations and Efficiency Comparisons(Elsevier, 2019) Aydıner, Coşkun; Mert, Berna Kiril; Doğan, Esra Can; Yatmaz, Hüseyin Cengiz; Dağlı, Sönmez; Aksu, Şeyda; Gören, Ayşegül Yağmur; Balcı, EsinFeasible reclamation of industrial wastewaters by consuming less resource and time requires researchers to develop advanced and sophisticated solutions to meet today's versatile needs. In this respect, novel technological applications of hybrid membrane oxidation reactor (MOR) comprising of the Fenton or photo-Fenton enhanced ultrafiltration (FEUF and pFEUF), was demonstrated for treating textile washing wastewater. Their comparative hybrid performances were explored based on response surface analyses of Taguchi experimental designs that were optimized for maximized responses at minimum oxidant and acid consumptions. From eleven specific variables, those affecting the hybrid treatment performances at significant levels were found as H2O2 amount, process time, membrane type, Fe2+ concentration and temperature. The pFEUF treatment showed better and faster organics removal efficiency than by FEUF, and the UF process was seen to be more affected from changing operational conditions in pFEUF. Organic pollutants were oxidized by 56.6 +/- 8.7% degradation and 31.5 +/- 3.2% mineralization, while UF allowed a synergistic contribution to the hybrid MOR performance by 38.1 +/- 4.7% and 17.3 +/- 3.1%, respectively. Compared to simultaneous MOR and external UF after Fenton, sequential MOR was found as the best solution by an efficiency of 84.5% COD, 70.5% TOC, and 155.6 L/m(2).h. The effluents could be readily produced with quality suitable for directly discharging to the sewage infrastructure system resulting in a complete treatment. This study proved that the developed MOR techniques are technologically favorable for the treatment of industrial organic wastewaters due to high treatment performances and less resource, time and land needs. It can be finally declared that they can be used as rather attractive solutions for not only wastewater reclamation but also water recovery by further handling of their effluents. (C) 2019 Elsevier B.V. All rights reserved.Article Citation - WoS: 46Citation - Scopus: 53Chitosan-Hybrid Poss Nanocomposites for Bone Regeneration: the Effect of Poss Nanocage on Surface, Morphology, Structure and in Vitro Bioactivity(Elsevier, 2020) Tamburacı, Sedef; Tıhmınlıoğlu, FundaPOSS, regarded as the smallest silica particle, is widely used as nanofiller in polymer systems. POSS-based nanocomposites are deduced as novel materials having potency for biomedical applications owing to the enhanced biocompatibility and physicochemical characteristics. The aim of this work was to integrate the beneficial features of chitosan (CS) and OctaTMA-POSS nanoparticle to design nanocomposite for bone tissue regeneration. The nanocomposite scaffolds were fabricated by freeze-drying. The effects of POSS incorporation on morphology and structure of CS matrix were examined. Bioactivity and osteogenic effects of the POSS nanoparticles were investigated with cytocompatibility, cell proliferation, alkaline phosphatase activity, osteocalcin production and biomineralization assays. PUSS incorporation altered the surface morphology by increasing surface roughness. Nanocomposite scaffolds with 82-90% porosity exhibited an increase in compression modulus of scaffolds (78-107 kPa) compared to control CS group (56 kPa). Results indicated that CS-POSS scaffolds were found cytocompatible with 3T3, MG-63 and Saos-2 cell lines. POSS incorporation showed promising effects on osteoblast adhesion and proliferation as well as increasing ALP activity, octeocalcin secretion and biomineralization of cells. (C) 2019 Elsevier B.V. All rights reserved.