Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
31 results
Search Results
Article Citation - WoS: 4Citation - Scopus: 5Breakthrough Curve Analysis of Phosphorylated Hazelnut Shell Waste in Column Operation for Continuous Harvesting of Lithium From Water(Elsevier, 2024) Recepoğlu, Yaşar Kemal; Arar, Ozguer; Yuksel, AsliIn batch-scale operations, biosorption employing phosphorylated hazelnut shell waste (FHS) revealed excellent lithium removal and recovery efficiency. Scaling up and implementing packed bed column systems necessitates further design and performance optimization. Lithium biosorption via FHS was investigated utilizing a continuous-flow packed-bed column operated under various flow rates and bed heights to remove Li to ultra-low levels and recover it. The Li biosorption capacity of the FHS column was unaffected by the bed height, however, when the flow rate was increased, the capacity of the FHS column decreased. The breakthrough time, exhaustion time, and uptake capacity of the column bed increased with increasing column bed height, whereas they decreased with increasing influent flow rate. At flow rates of 0.25, 0.5, and 1.0 mL/min, bed volumes (BVs, mL solution/mL biosorbent) at the breakthrough point were found to be 477, 369, and 347, respectively, with the required BVs for total saturation point of 941, 911, and 829, while the total capacity was calculated as 22.29, 20.07, and 17.69 mg Li/g sorbent. In the 1.0, 1.5, and 2.0 cm height columns filled with FHS, the breakthrough times were 282, 366, and 433 min, respectively, whereas the periods required for saturation were 781, 897, and 1033 min. The three conventional breakthrough models of the Thomas, Yoon-Nelson, and Modified Dose-Response (MDR) were used to properly estimate the whole breakthrough behavior of the FHS column and the characteristic model parameters. Li's extremely favorable separation utilizing FHS was evidenced by the steep S-shape of the breakthrough curves for both parameters flow rate and bed height. The reusability of FHS was demonstrated by operating the packed bed column in multi-cycle mode, with no appreciable loss in column performance.Erratum Citation - WoS: 1Corrigendum: Bioactive Snail Mucus-Slime Extract Loaded Chitosan Scaffolds for Hard Tissue Regeneration: The Effect of Mucoadhesive and Antibacterial Extracts on Physical Characteristics and Bioactivity of Chitosan Matrix (2021biomed. Mater.16 065008)(NLM (Medline), 2023) Perpelek, M.; Tamburaci, S.; Aydemir, S.; Tıhmınlıoğlu, F.; Baykara, B.; Karakaşli, A.; Havitçioǧlu, H.Article Citation - WoS: 11Fabrication of Helix Aspersa Extract Loaded Gradient Scaffold With an Integrated Architecture for Osteochondral Tissue Regeneration: Morphology, Structure, and in Vitro Bioactivity [2](American Chemical Society, 2023) Tamburacı, Sedef; Perpelek, Merve; Aydemir, Selma; Baykara, Başak; Havıtçıoğlu, Hasan; Tıhmınlıoğlu, FundaRegeneration of osteochondral tissue with its layered complex structure and limited self-repair capacity has come into prominence as an application area for biomaterial design. Thus, literature studies have aimed to design multilayered scaffolds using natural polymers to mimic its unique structure. In this study, fabricated scaffolds are composed of transition layers both chemically and morphologically to mimic the gradient structure of osteochondral tissue. The aim of this study is to produce gradient chitosan (CHI) scaffolds with bioactive snail (Helix aspersa) mucus (M) and slime (S) extract and investigate the structures regarding their physicochemical, mechanical, and morphological characteristics as well as in vitro cytocompatibility and bioactivity. Gradient scaffolds (CHI-M and CHI-S) were fabricated via a layer-by-layer freezing and lyophilization technique. Highly porous and continuous 3D structures were obtained and observed with SEM analysis. In addition, scaffolds were physically characterized with water uptake test, micro-CT, mechanical analysis (compression tests), and XRD analysis. In vitro bioactivity of scaffolds was investigated by co-culturing Saos-2 and SW1353 cells on each compartment of gradient scaffolds. Osteogenic activity of Saos-2 cells on extract loaded gradient scaffolds was investigated in terms of ALP secretion, osteocalcin (OC) production, and biomineralization. Chondrogenic bioactivity of SW1353 cells was investigated regarding COMP and GAG production and observed with Alcian Blue staining. Both mucus and slime incorporation in the chitosan matrix increased the osteogenic differentiation of Saos-2 and SW1353 cells in comparison to the pristine matrix. In addition, histological and immunohistological staining was performed to investigate ECM formation on gradient scaffolds. Both characterization and in vitro bioactivity results indicated that CHI-M and CHI-S scaffolds show potential for osteochondral tissue regeneration, mimicking the structure as well as enhancing physical characteristics and bioactivity. © 2023 The Authors. Published by American Chemical Society.Article Citation - WoS: 16Citation - Scopus: 15Ultrasound-Assisted Dopamine Polymerization: Rapid and Oxidizing Agent-Free Polydopamine Coatings on Membrane Surfaces(Royal Society of Chemistry, 2021) Cihanoğlu, Aydın; Schiffman, Jessica D.; Alsoy Altınkaya, SacideHerein, we report a controllable pathway to accelerate the polymerization kinetics of dopamine using ultrasound as a trigger. The use of ultrasound was demonstrated to dramatically accelerate the slow liquid phase reaction kinetics and increase the deposition rate of the polydopamine coating on the surface of polymeric membranes.Article Citation - WoS: 10Citation - Scopus: 12Enhanced Model Protein Adsorption of Nanoparticulate Hydroxyapatite Thin Films on Silk Sericin and Fibroin Surfaces(Springer, 2022) Özcan, Selçuk; Çiftçioğlu, MuhsinHydroxyapatite coated metallic implants favorably combine the required biocompatibility with the mechanical properties. As an alternative to the industrial coating method of plasma spraying with inherently potential deleterious effects, sol-gel methods have attracted much attention. In this study, the effects of intermediate silk fibroin and silk sericin layers on the protein adsorption capacity of hydroxyapatite films formed by a particulate sol-gel method were determined experimentally. The preparation of the layered silk protein/hydroxyapatite structures on glass substrates, and the effects of the underlying silk proteins on the topography of the hydroxyapatite coatings were described. The topography of the hydroxyapatite layer fabricated on the silk sericin was such that the hydroxyapatite particles were oriented forming an oriented crystalline surface. The model protein (bovine serum albumin) adsorption increased to 2.62 µg/cm2 on the latter surface as compared to 1.37 µg/cm2 of hydroxyapatite on glass without an intermediate silk sericin layer. [Figure not available: see fulltext.].Article Citation - WoS: 7Citation - Scopus: 7Synthesis and Characterization of Single-Walled Carbon Nanotube: Cyto-Genotoxicity in Allium Cepa Root Tips and Molecular Docking Studies(Wiley, 2022) İnce Yardımcı, Atike; İstifli, Erman Salih; Açıkbaş, Yaser; Liman, Recep; Yağmurcukardeş, Nesli; Yılmaz, Selahattin; Ciğerci, İbrahim HakkıHerein, single-walled carbon nanotubes (SWCNTs) were synthesized by the thermal chemical vapor deposition (CVD) method, and characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM), Raman spectroscopy, dynamic light scattering (DLS), and thermo-gravimetric analysis (TGA). The results indicated that obtained nanotubes were SWCNTs with high crystallinity and their average diameter was 10.15 ± 3 nm. Allium cepa ana–telophase and comet assays on the root meristem were employed to evaluate the cytotoxic and genotoxic effects of SWCNTs by examining mitotic phases, mitotic index (MI), chromosomal aberrations (CAs), and DNA damage. A. cepa root tip cells were exposed to SWCNTs at concentrations of 12.5, 25, 50, and 100 μg/ml for 4 h. Distilled water and methyl methanesulfonate (MMS, 10 μg/ml) were used as the negative and positive control groups, respectively. It was observed that MIs decreased statistically significantly for all applied doses. Besides, CAs such as chromosome laggards, disturbed anaphase–telophase, stickiness and bridges and also DNA damage increased in the presence of SWCNTs in a concentration-dependent manner. In the molecular docking study, the SWCNT were found to be a strong DNA major groove binder showing an energetically very favorable binding free energy of −21.27 kcal/mol. Furthermore, the SWCNT interacted effectively with the nucleotides on both strands of DNA primarily via hydrophobic π and electrostatic interactions. As a result, cytotoxic and genotoxic effects of SWCNTs in A. cepa root meristematic cells which is a reliable system for assessment of nanoparticle toxicology were demonstrated in this study.Article Citation - WoS: 11Citation - Scopus: 12Numerical Modelling Assisted Design of a Compact Ultrafiltration (uf) Flat Sheet Membrane Module(MDPI, 2021) Bopape, Mokgadi F.; Van Geel, Tim; Dutta, Abhishek; Van der Bruggen, Bart; Onyango, Maurice StephenThe increasing adoption of ultra-low pressure (ULP) membrane systems for drinking water treatment in small rural communities is currently hindered by a limited number of studies on module design. Detailed knowledge on both intrinsic membrane transport properties and fluid hydrodynamics within the module is essential in understanding ULP performance prediction, mass transfer analysis for scaling-up between lab-scale and industrial scale research. In comparison to hollow fiber membranes, flat sheet membranes present certain advantages such as simple manufacture, sheet replacement for cleaning, moderate packing density and low to moderate energy usage. In the present case study, a numerical model using computational fluid dynamics (CFD) of a novel custom flat sheet membrane module has been designed in 3D to predict fluid flow conditions. The permeate flux through the membrane decreased with an increase in spacer curviness from 2.81 L/m(2)h for no (0%) curviness to 2.73 L/m(2)h for full (100%) curviness. A parametric analysis on configuration variables was carried out to determine the optimum design variables and no significant influence of spacer inflow or outflow thickness on the fluid flow were observed. The numerical model provides the necessary information on the role of geometrical and operating parameters for fabricating a module prototype where access to technical expertise is limited.Article Citation - WoS: 7Citation - Scopus: 8Compositional, Microstructural and Mechanical Effects of Nacl Porogens in Brushite Cement Scaffolds(Elsevier, 2021) Şahin, Erdem; Çiftçioğlu, MuhsinModification of the setting process of brushite cements by varying the concentration of ions that alter calcium phosphate crystallization kinetics, is known to enable control on the monetite conversion extent and the accompanying microporosity. This is useful because monetite serves as a suitable matrix in macroporous scaffolds due to its higher phase stability and finer crystal morphology compared to its hydrous counterpart brushite. In this study the synergistic effect of NaCl and citric acid on the microstructural evolution of brushite cement was demonstrated and microporosity of macroporous monetite-rich cement blocks was minimized by a variable NaCl porogen size distribution approach. Initially, maximum packing ratio of various combinations of NaCl size groups in PEG were determined by their rheological analysis in a range between 57% and 69%. Statistical analysis revealed a positive correlation between the amounts of NaCl particles under 38 mu m and 212 mu m and the maximum packing ratio. Further broadening the size distributions of NaCl porogens with fine cement precursors was effective in increasing the solids packing ratio of cement blocks more than the maximum packing ratio for the porogens. This improvement in packing was accompanied by a reduction in microporosity despite the increase in micropore volume with ion induced monetite formation. The detrimental effect of the microporosity introduced to the structure during monetite formation was balanced for some size distributions and not so much for others, thereby resulting in a wide range of porosities and mechanical properties. Thus, the exponential dependence of mechanical properties on porosity and the mechanical properties of monetite-rich macroporous blocks at the theoretical zero-porosity were determined according to Rice's model. Zero-porosity extrapolations were much higher than those predicted for brushite cement, contrary to the common assumption that brushite is mechanically stronger than monetite.Article Citation - WoS: 22Citation - Scopus: 23Bioactive Snail Mucus-Slime Extract Loaded Chitosan Scaffolds for Hard Tissue Regeneration: the Effect of Mucoadhesive and Antibacterial Extracts on Physical Characteristics and Bioactivity of Chitosan Matrix(IOP Publishing, 2021) Perpelek, Merve; Tamburacı, Sedef; Aydemir, Selma; Tıhmınlıoğlu, Funda; Baykara, Başak; Karakaşlı, Ahmet; Havıtçıoğlu, HasanBiobased extracts comprise various bioactive components and they are widely used in tissue engineering applications to increase bioactivity as well as physical characteristics of biomaterials. Among animal sources, garden snail Helix aspersa has come into prominence with its antibacterial and regenerative extracts and show potential in tissue regeneration. Thus, in this study, bioactive H. aspersa extracts (slime, mucus) were loaded in chitosan (CHI) matrix to fabricate porous scaffolds for hard tissue regeneration. Physical, chemical properties, antimicrobial activity was determined as well as in vitro bioactivity for bone and cartilage regeneration. Mucus and slime incorporation enhanced mechanical properties and biodegradation rate of CHI matrix. Scanning electron microscopy images showed that the average pore size of the scaffolds decreased with higher extract content. Mucus and slime extracts showed antimicrobial effect on two bacterial strains. In vitro cytotoxicity, osteogenic and chondrogenic activity of the scaffolds were evaluated with Saos-2 and SW1353 cell lines in terms of Alkaline phosphatase activity, biomineralization, GAG, COMP and hydroxyproline content. Cell viability results showed that extracts had a proliferative effect on Saos-2 and SW1353 cells when compared to the control group. Mucus and slime extract loading increased osteogenic and chondrogenic activity. Thus, the bioactive extract loaded CHI scaffolds showed potential for bone and cartilage regeneration with enhanced physical properties and in vitro bioactivity.Article Citation - WoS: 69Citation - Scopus: 77Novel Zein-Based Multilayer Wound Dressing Membranes With Controlled Release of Gentamicin(John Wiley and Sons Inc., 2019) Kimna, Ceren; Tamburacı, Sedef; Tıhmınlıoğlu, FundaRecently, functional multilayer scaffolds with controlled drug release ability come into prominence for wound healing applications to mimic the layered structure of skin tissue and prevent the possible infections at the defect site. In this study, controlled antibiotic releasing zein bilayer membranes were fabricated for treatment of acute skin infections. Gentamicin loaded fibers were prepared by electrospinning on the membrane surface. Membranes were characterized with scanning electron microscope, atomic force microscopy, Fourier transform infrared spectroscopy, contact angle, mechanical analysis, swelling, degradation, and water vapor permeability studies. In vitro cytotoxicity, cell attachment, and proliferation were investigated. Cell attachment on fiber layer was observed with fluorescence imaging. Fabricated fibers showed structural similarity to the skin tissue layers with a fiber diameter range of 350-425 nm and film thickness in the range of 311-361 mu m. Mechanical properties were found compatible with the skin tissue. In addition, membranes showed antimicrobial activity against Staphylococcus aureus and Escherichia coli. The sustained release was achieved with a cumulative release of 94%. Membranes did not show any cytotoxic effect. NIH/3T3 and HS2 cell lines were proliferated on each layer mimicking the multilayer skin tissue. Hence, zein-based bilayer membrane showed promising properties to be used as a potential antimicrobial wound dressing for skin tissue regeneration. (c) 2018 Wiley Periodicals, Inc.