Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
6 results
Search Results
Article Citation - WoS: 23Citation - Scopus: 24Epoxidation of Propene by High-Throughput Screening Method Over Combinatorially Prepared Cu Catalysts Supported on High and Low Surface Area Silica(Springer Verlag, 2012) Düzenli, Derya; Şeker, Erol; Senkan, Selim; Önal, IşıkGas phase epoxidation of propene using molecular oxygen was studied by use of a high-throughput testing technique. A large number of catalysts including promoted and un-promoted Cu were synthesized in a much faster combinatorial fashion using a sol-gel method. Metal catalysts supported on high and low surface area silica were tested and ranked in a high-throughput activity and selectivity testing apparatus at different experimental conditions such as reaction temperature and reactant gas ratio. The amount of Cu loading and the addition of alkali promoters such as K and Li resulted in different tendencies in consumption rate for both silica materials. The maximum PO production rate was obtained as 25.82 μmol/g/ cat./min (2.90 % conv. and 20.49 % selectivity) for 3 % Cu-2.25 % K catalyst supported on high surface area silica. There was no noticeable difference in structural and chemical properties of catalysts after modification with K when examined by XRD and TEM; however, the overall activation energy of un-modified catalysts (92 kJ/mol) decreased to 71 kJ/mol for K-modified catalyst. There was negligible difference between the activation energies calculated for PO production (75 vs. 77 kJ/mol).Article Citation - WoS: 6Citation - Scopus: 7Influence of Calcination Temperature on Microstructure and Surface Charge of Membrane Top Layers Composed of Zirconia Nanoparticles(Springer Verlag, 2015) Erdem, İlker; Çiftçioğlu, MuhsinThe purpose of the research is to investigate the changes in microstructure and physicochemical characteristics, mainly surface charge (i.e. zeta potential) of zirconia membrane top layer during calcination. Zirconia is one of the most commonly preferred materials for ceramic membrane top layers due to its superior durability. The physicochemical properties of the top layer composed of submicron / nano particles is necessary not only for Donnan exclusion but also for dynamics of membrane fouling. In the present research the possibility of preparation of zirconia top layers with varying surface charge with changing calcination temperature was shown and a correlation between phase transformation and surface charge was determined.Article Citation - WoS: 2Citation - Scopus: 3Preparation and Characterization of Diphasic Sol-Gel Derived Unsupported Mullite Membranes(Springer Verlag, 2011) Topuz, Berna; Çiftçioglu, MuhsinDiphasic gels prepared by mixing freshly prepared polymeric silica and polymeric boehmite sols through a modified Al-alkoxide route in mullite compositions led to the crystallization of mullite upon heat treatment at 775°C. Mullite formation was observed at a 100°C higher temperature when diphasic gels were formed by mixing aged polymeric sols containing about 2 nm in diameter boehmite species. These relatively low mullite formation temperatures were attributed to the nanoscale sizes of the polymeric species of the two amorphous phases present in the diphasic gels.Article Citation - WoS: 12Citation - Scopus: 13Single Step Sol-Gel Made Silver Chloride on Titania Xerogels To Inhibit E. Coli Bacteria Growth: Effect of Preparation and Chloride Ion on Bactericidal Activity(Springer Verlag, 2011) Tuncer, Mert; Şeker, ErolWe report the antibacterial efficacies of silver and/or silver chloride containing titania xerogels synthesized with modified single step sol-gel methods against Escherichia coli bacteria. As the silver loading in TiO 2 increases, the amount of the xerogel required to inhibit the growth of the bacteria decreases and also we found that pure TiO2 was not bactericidal. Among modified single step sol-gel methods used in this study, the additional HCl treatment sol-gel route III was very effective to obtain only AgCl crystallites in TiO2. Based on viable cell count method, 0.125 g/L of 29%Ag/TiO2 (made with HNO3 sol-gel route I) was enough to inhibit the growth of E. coli whereas 0.6 g/L of 29%Ag/TiO2 (made with the additional HCl treatment sol-gel route III) was required. However, antibacterial activity of 29%Ag/TiO2 (made with HNO 3 sol-gel route I) after 6 usages was the same as 29%Ag/TiO 2 (made with the additional HCl treatment sol-gel route III).Conference Object Citation - WoS: 22Citation - Scopus: 22Propylene Epoxidation: High-Throughput Screening of Supported Metal Catalysts Combinatorially Prepared by Rapid Sol-Gel Method(Springer Verlag, 2010) Önal, Işık; Düzenli, Derya; Seubsai, Anusorn; Kahn, Michael; Şeker, Erol; Senkan, Selim M.The gas phase oxidation of propylene using molecular oxygen was studied on a variety of supported metal catalysts. The most promising PO activity was obtained for Cu supported on high surface area SiO 2 and the multimetallic systems exhibit synergistic effects that increased the desired PO yield by several folds for Ag promoted with Cu on SiO 2 after screening a large number of catalysts by a high throughput testing technique. © 2009 Springer Science+Business Media, LLC.Article Citation - WoS: 36Citation - Scopus: 42Sol-Gel Derived Mesoporous and Microporous Alumina Membranes(Springer Verlag, 2010) Topuz, Berna; Çiftçioğlu, MuhsinStable polymeric and colloidal boehmite sols were prepared by sol-gel process through controlled hydrolysis/condensation reactions. The particle sizes of the colloidal sols were in the 12-25 nm range depending on the process parameters and about 2 nm for polymeric sols. The presence of a significant increase in the microporosity content of the heat treated polymeric membranes relative to the mesoporous colloidal membranes might make the design of thermally stable microporous alumina membranes with controlled pore structures possible. The phase structure evolution in the 600-800 °C range had shown that the crystallization of the gamma alumina in the amorphous matrix starts at about 800 °C. This indicated that the pore structure stability may be enhanced through processing up to this relatively high temperature in polymeric alumina derived unsupported membranes. The permeance values of the two and three layered colloidal alumina membranes were observed to be independent of pressure which implies that the dominant gas transport mechanism is Knudsen diffusion in these structures. This was also supported by the 2.8 nm BJH pore sizes of the colloidal membranes. The Knudsen diffusion equation derived permeances of the polymeric alumina membranes with thicknesses of about 300 nm were determined to be very close to the experimentally determined permeance values. © 2010 Springer Science+Business Media, LLC.