Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
8 results
Search Results
Article Citation - WoS: 16Citation - Scopus: 15Ultrasound-Assisted Dopamine Polymerization: Rapid and Oxidizing Agent-Free Polydopamine Coatings on Membrane Surfaces(Royal Society of Chemistry, 2021) Cihanoğlu, Aydın; Schiffman, Jessica D.; Alsoy Altınkaya, SacideHerein, we report a controllable pathway to accelerate the polymerization kinetics of dopamine using ultrasound as a trigger. The use of ultrasound was demonstrated to dramatically accelerate the slow liquid phase reaction kinetics and increase the deposition rate of the polydopamine coating on the surface of polymeric membranes.Article Citation - WoS: 5Citation - Scopus: 5Flat sheet metakaolin ceramic membrane for water desalination via direct contact membrane distillation(IWA Publishing, 2022) Zewdie, Tsegahun Mekonnen; Habtu, Nigus Gabbiye; Dutta, Abhishek; Van der Bruggen, BartHydrophobic metakaolin-based flat sheet membrane was developed via phase inversion and sintering technique and modified through 1H,1H,2H,2H-perfluorooctyltriethoxysilane grafting agents. The prepared membrane was characterized by different techniques such as XRD, FTIR, SEM, contact angle, porosity, and mechanical strength. Their results indicated that the wettability, structural, and mechanical properties of the prepared membrane confirm the suitability of the material for membrane distillation (MD) application. The prepared metakaolin-based flat sheet membrane acquired hydrophobic properties after surface modification with the water contact angle values of 113.2° to 143.3°. Afterward, the membrane performance was tested for different sodium chloride aqueous solutions (synthetic seawater) and various operating parameters (feed temperature, feed flow rate) using direct contact membrane distillation (DCMD). Based on the findings, the prepared membrane at metakaolin loading of 45 wt.% and sintered at 1,300 °C was achieved the best performance with >95% salt rejection and permeate flux of 6.58 + 0.3 L/m2 · h at feed temperature of 80 °C, feed concentration of 35 g/L, and feed flow rate of 60 L/h. It can be con-cluded that further optimization of membrane porosity, mechanical, and surface properties is required to maximize the permeate flux and salt rejection.Article Citation - WoS: 11Citation - Scopus: 12Numerical Modelling Assisted Design of a Compact Ultrafiltration (uf) Flat Sheet Membrane Module(MDPI, 2021) Bopape, Mokgadi F.; Van Geel, Tim; Dutta, Abhishek; Van der Bruggen, Bart; Onyango, Maurice StephenThe increasing adoption of ultra-low pressure (ULP) membrane systems for drinking water treatment in small rural communities is currently hindered by a limited number of studies on module design. Detailed knowledge on both intrinsic membrane transport properties and fluid hydrodynamics within the module is essential in understanding ULP performance prediction, mass transfer analysis for scaling-up between lab-scale and industrial scale research. In comparison to hollow fiber membranes, flat sheet membranes present certain advantages such as simple manufacture, sheet replacement for cleaning, moderate packing density and low to moderate energy usage. In the present case study, a numerical model using computational fluid dynamics (CFD) of a novel custom flat sheet membrane module has been designed in 3D to predict fluid flow conditions. The permeate flux through the membrane decreased with an increase in spacer curviness from 2.81 L/m(2)h for no (0%) curviness to 2.73 L/m(2)h for full (100%) curviness. A parametric analysis on configuration variables was carried out to determine the optimum design variables and no significant influence of spacer inflow or outflow thickness on the fluid flow were observed. The numerical model provides the necessary information on the role of geometrical and operating parameters for fabricating a module prototype where access to technical expertise is limited.Article Citation - WoS: 69Citation - Scopus: 77Novel Zein-Based Multilayer Wound Dressing Membranes With Controlled Release of Gentamicin(John Wiley and Sons Inc., 2019) Kimna, Ceren; Tamburacı, Sedef; Tıhmınlıoğlu, FundaRecently, functional multilayer scaffolds with controlled drug release ability come into prominence for wound healing applications to mimic the layered structure of skin tissue and prevent the possible infections at the defect site. In this study, controlled antibiotic releasing zein bilayer membranes were fabricated for treatment of acute skin infections. Gentamicin loaded fibers were prepared by electrospinning on the membrane surface. Membranes were characterized with scanning electron microscope, atomic force microscopy, Fourier transform infrared spectroscopy, contact angle, mechanical analysis, swelling, degradation, and water vapor permeability studies. In vitro cytotoxicity, cell attachment, and proliferation were investigated. Cell attachment on fiber layer was observed with fluorescence imaging. Fabricated fibers showed structural similarity to the skin tissue layers with a fiber diameter range of 350-425 nm and film thickness in the range of 311-361 mu m. Mechanical properties were found compatible with the skin tissue. In addition, membranes showed antimicrobial activity against Staphylococcus aureus and Escherichia coli. The sustained release was achieved with a cumulative release of 94%. Membranes did not show any cytotoxic effect. NIH/3T3 and HS2 cell lines were proliferated on each layer mimicking the multilayer skin tissue. Hence, zein-based bilayer membrane showed promising properties to be used as a potential antimicrobial wound dressing for skin tissue regeneration. (c) 2018 Wiley Periodicals, Inc.Article Citation - WoS: 1Citation - Scopus: 1The Effect of Mass Transfer Resistance and Nonuniform Initial Solvent Concentration on Permeation Through Polymer Membranes(John Wiley and Sons Inc., 2018) Zielinski, John M.; Alsoy Altınkaya, SacideA numerical simulation model has been developed which enables one to examine the effects of surface mass transfer resistance on the evaluation of permeation (P*), diffusion (D), and solubility (S) coefficients from unsteady-state mass transfer experiments as well as the transmission rate. A complementary analytical expression has been developed which validates the numerical model and facilitates the evaluation of the concentration dependence of P*, D, and S from sequential step-change experiments, under experimental conditions when the surface mass transfer resistance can be neglected.Article Citation - WoS: 17Citation - Scopus: 19Effect of Operational Conditions on Separation of Lithium From Geothermal Water by ?-Mno2 Using Ion Exchange–membrane Filtration Hybrid Process(Taylor and Francis Ltd., 2018) Recepoğlu, Yaşar Kemal; Kabay, Nalan; Yoshizuka, Kazuharu; Nishihama, Syouhei; Yılmaz İpek, İdil; Arda, Müşerref; Yüksel, MithatA hybrid system coupling ion exchange and ultrafiltration (UF) was employed to separate lithium from lithium-spiked geothermal water. The effect of process parameters such as adsorbent type, adsorbent dosage, permeate flow rate, and replacement speeds of fresh and saturated adsorbents have been evaluated to determine the efficiency of the hybrid system. According to the results obtained using λ-MnO2 derived from spinel-type lithium manganese dioxide, the optimal operating conditions to separate lithium from geothermal water were found with powdery λ-MnO2 with an adsorbent concentration of 1.5 g adsorbent/L solution, replacement rates of fresh and saturated adsorbents of 6.0 mL/min, and a permeate flow rate of 5.0 mL/min. The ion exchange–UF hybrid system providing an advantage to work with very fine particles easily can be considered as a favorable process for the separation of lithium from geothermal water.Article Citation - WoS: 13Citation - Scopus: 15Ancillary Effects of Surfactants on Filtration of Low Molecular Weight Contaminants Through Cellulose Nitrate Membrane Filters(Elsevier Ltd., 2016) Olcay, Aybike Nil; Polat, Mehmet; Polat, HürriyetRemoval of contaminants with low molecular weight (<800 Dalton) requires the use of advanced separation techniques such as ultrafiltration (UF) or micellar enhanced ultrafiltration (MEUF). However, surface active agents invariably co-exist in waste waters along with these contaminants or they may be added intentionally as part of the separation process as in the case of MEUF. Though it is quite likely that both the filter medium and the contaminants would interact with the surfactant molecules or their micelles, there is not sufficient emphasis in the literature on the concomitant aspects of such interactions.The ancillary effects created by anionic (sodium dodecyl sulfate, SDS), cationic (hexadecyltrimethyl ammonium bromide, CTAB) and non-ionic (ethoxylated octylphenol, TX-100) surfactants on the mechanism and efficiency of the filtration process were investigated in this study. Methylene blue (MB) and cellulose nitrate membrane (CNM) filters were employed as model retentate and the separation medium. A combination of surface tension, contact angle and charge measurements demonstrated that the addition of surfactants had a remarkable effect on the filtration outcome. The effect depended on both the type and concentration of the surfactant and was manifested mainly through the creation of MB-surfactant entities which acted differently than the MB alone; but more importantly, through the interactions of the surfactant molecules/micelles and the MB-surfactant pairs with the separation membrane.Article Citation - WoS: 29Citation - Scopus: 33Surface Modification of Polysulfone Based Hemodialysis Membranes With Layer by Layer Self Assembly of Polyethyleneimine/Alginate-heparin: a Simple Polyelectrolyte Blend Approach for Heparin Immobilization(Springer Verlag, 2013) Yaşar Mahlıçlı, Filiz; Alsoy Altınkaya, SacideThis study intends to improve blood compatibility of polysulfone (PSF) membranes by generating a nonthrombogenic surface through heparin immobilization. To achieve this task, the support membrane prepared from a blend of PSF and sulfonated polysulfone (SPSF) was modified with layer by layer (LBL) deposition of polyethyleneimine (PEI) and alginate (ALG) and heparin blended with ALG was immobilized only on the outermost surface of the LBL assembly. The results have shown that the adsorption of human plasma proteins and platelet activation on the LBL modified membranes decreased significantly compared with the unmodified PSF and PSF-SPSF blend membranes. Furthermore, blending ALG with a small amount of heparin remarkably prolonged the APTT values of heparin free PEI/ALG coated membranes. It is envisaged that the use of a blend of HEP and ALG only in the terminating layer of the LBL assembly can be an economical and alternative modification technique to create nonthrombogenic surfaces.