Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
5 results
Search Results
Article Citation - WoS: 3Citation - Scopus: 4Microfluidic-Assisted Preparation of Nano and Microscale Chitosan Based 3d Composite Materials: Comparison With Conventional Methods(Wiley, 2022) Kimna, Ceren; Değer, Sibel; Tamburacı, Sedef; Tıhmınlıoğlu, FundaAlthough nanofillers contribute to improved physical characteristics and biological functionalities of polymer-based biomaterials, their dispersion in polymer matrices is still a challenging issue in terms of obtaining consistency for the inherent properties. To tackle this problem, homogenization techniques are applied to disperse the nanofillers in such polymers, however, these methods can cause undesired changes especially in the rheological properties and the physical structure of the biopolymer matrices. Recently, as a novel homogenization technique, microfluidization has been used to homogenize polymer nanocomposites to minimize these limitations. In this study, two different nanocomposite structures as chitosan/montmorillonite (CS/MMT) and chitosan/polyhedral oligomeric silsesquioxane nanocages (CS/POSS) were homogenized with microfluidization and investigated in terms of physical alterations. Furthermore, the effect of microfluidizer technique on material characteristics was compared with conventional homogenization techniques, i.e., ultrasonic bath and sonication in terms of solution, nano – (e.g., hydrodynamic size, drug encapsulation) and macroscopic material characteristics (e.g., porosity, mechanical properties, swelling and thermal degradation). It was found that the microfluidizer homogenization improves the physical characteristics in both nano and macroscale materials: Nanospheres obtained from CS/MMT composites showed enhanced stability, uniform size distribution (<100 nm, PDI: [removed]50%) whereas 3D porous CS/POSS scaffolds showed improved structural uniformity (i.e., homogeneous and interconnected microstructure) and enhanced thermal and mechanical properties. The obtained results indicate that the microfluidizer homogenization ensures a successful nanofiller dispersion in polymer matrices, thereby improving the biomaterial characteristics impressively compared to the sonication methods.Article Citation - WoS: 19Citation - Scopus: 20Isothermal Crystallization Kinetics and Mechanical Properties of Polycaprolactone Composites With Zinc Oxide, Oleic Acid, and Glycerol Monooleate(John Wiley and Sons Inc., 2013) Alp, Burcu; Cesur, SerapThe isothermal crystallization and mechanical behavior of polycaprolactone (PCL) with zinc oxide (ZnO) with oleic acid and glycerol monooleate (GMO) were studied. Theoretical melting points calculated by the Flory-Huggins and Thompson-Gibbs models were thoroughly compared with differential scanning calorimetry experimental observations. The isothermal crystallization kinetic parameters by Avrami analysis showed that crystallization was controlled by nucleation, crystal growth was spherical, and the nucleation type changed between thermal and athermal nucleation. X-ray diffraction showed that when the additives were used together both the crystal thickness and the degree of crystallinity increased. A multiple-response regression analysis was made with the ZnO, oleic acid, and GMO concentrations as variables and the crystallinity as output. Interaction parameters by the Pukanzky model were calculated from the tensile strength at the yield point and indicated that the addition of oleic acid or GMO improved the interface between the ZnO particles and PCL.Article Citation - WoS: 17Citation - Scopus: 21Effects of Particle Size and Electrical Resistivity of Filler on Mechanical, Electrical, and Thermal Properties of Linear Low Density Polyethylene-Zinc Oxide Composites(John Wiley and Sons Inc., 2013) Özmıhçı Ömürlü, Filiz; Balköse, DevrimThe effects of particle size and electrical resistivity of zinc oxide (ZnO) on mechanical properties, electrical and thermal conductivities of composites made with linear low density polyethylene (LLDPE) were investigated. Micron sized (mZnO), submicron sized (sZnO), and nano sized (nZnO) powders having resistivities of 1.5 × 106, 1.5 × 109, and 1.7 × 108 were used to prepare composites with 5-20 vol % filler. The tensile strength was lowered and the modulus of elasticity of the composites was increased with ZnO addition. Rather than the particle size of the ZnO, its initial resistivity and aspect ratio affected the resistivity of composites. The resistivity of the LLDPE was lowered from 2.3 × 1016 Ω cm down to 1.4 × 1010 Ω cm with mZnO addition. Thermal conductivity of the composites was increased with ZnO addition 2.5-3 times of the polymer matrix. The composites can be used for electrostatically dissipating and heat sink applications due to their decreased electrical resistivity and increased thermal conductivity.Article Citation - WoS: 13Citation - Scopus: 18Effect of Corn-Zein Coating on the Mechanical Properties of Polypropylene Packaging Films(John Wiley and Sons Inc., 2011) Tıhmınlıoğlu, Funda; Atik, İsa Doğan; Özen, BanuIn this study, a novel film structure of corn zein coated on polypropylene (PP) synthetic films for food packaging applications was developed, and the mechanical properties of the resulting coated film, as affected by the coating formulation, were investigated. Composite structures of PP films coated with corn zein were obtained through a simple solvent casting method. Different amounts of corn zein (5 and 15%) were dissolved in 70 and 95% aqueous ethanol solution at 50 C. Solutions of corn zein plasticized with poly(ethylene glycol) and glycerol (GLY) at various levels (20 and 50%) were applied on corona-discharge-treated PP. A statistical analysis based on full factorial design was performed to examine the influence of the coating formulation on the final properties of the corn-zein-coated PP films. A significant (p < 0.05) improvement in the coated film’s mechanical properties was observed compared to those of the uncoated PP. The effect of the plasticization of the coating solutions was also quite significant. In general, GLY provided better improvements in the mechanical properties of the corn-zein-coated PP films. The statistical analysis of the results showed that the corn-zein and plasticizer concentrations and plasticizer type used in the coating formulations were more effective parameters and had significant effects on the mechanical behavior of the coated PP films. In conclusion, corn-zein coatings could have potential as alternatives to conventional synthetic polymers used in composite multilayer structures for food packaging applications.Article Citation - WoS: 64Citation - Scopus: 70Mechanical and Morphological Properties of Recycled High-Density Polyethylene, Filled With Calcium Carbonate and Fly Ash(John Wiley and Sons Inc., 2006) Atikler, Ulaş; Başalp, Dildare; Tıhmınlıoğlu, FundaIn this study, mechanical and morphological properties of composites made up of recycled high-density polyethylene (HDPE) filled with calcium carbonate and fly ash (FA) were studied. Interfacial interactions were modified to improve the filler compatibility and mechanical properties of the composites by surface treatment of the FA filler with 3-amino propyl triethoxy silane. The composites were prepared by using a Thermo Haake Rheomixer. Effect of filler loading and treatment of FA with silane coupling agent on mechanical and morphological properties were investigated and it was found that silane treatment indicated significant improvements on the mechanical properties of the HDPE-FA composites. The improvement with silane treatment of FA was also confirmed by applying the Pukanszky model. Scanning electron microscopy on the fracture surface of composites had given direct evidence of better interfacial adhesion via silane treatment.