Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
13 results
Search Results
Now showing 1 - 10 of 13
Article Citation - WoS: 4Citation - Scopus: 5Antifouling Polydopamine-Modified Poly (ether Sulfone) Membrane Immobilized With Alumina-Calcium Oxide Catalyst for Continuous Biodiesel Production(Elsevier, 2023) Güngörmüş, Elif; Şeker, Erol; Alsoy Altınkaya, SacideBiodiesel is an alternative biofuel that can be blended with conventional petroleum-derived diesel fuel to partly reduce the dependence on the imported oil. Catalytic membrane reactors are promising candidates for sustainable biodiesel production. Herein, we report a novel catalytically active polydopamine-modified poly (ether sulfone) (PES) membrane immobilized with an alumina-calcium oxide catalyst. The reaction temperature, butanol to canola oil ratio, and transmembrane pressure applied through the membrane were optimized with response surface methodology and Box-Behnken design. In contrast to all previous catalytic membrane studies for biodiesel production, we used butanol as a co-reactant to improve the winter problems of biodiesel made with methanol. FTIR and SEM-EDX analysis confirmed the successful immobilization of the catalyst. At the end of 30 days of storage in the reactant mixture, 95% of the catalyst loaded to the membrane was still on the surface, and biodiesel yield values and butanol flux of the membrane did not change. We compared the batch and flowthrough operation modes by measuring the catalytic activity of membranes under static and dynamic conditions within 24 h (8-cycle). The biodiesel yield under dynamic condition decreased in the first three cycles from 54.54 +/- 0.65% to 47.31 +/- 0.70% and then stayed constant, whereas a continuous decrease from 25.42 +/- 0.57% to 17.19 +/- 0.58% was observed under static condition. In each cycle, the equilibrium limitation for the yield was overcome only when the membrane was operated under pressure. The main reason for the decrease in catalytic activities was the fouling on the catalyst surface which was quickly removed by backwashing with butanol. It is concluded that catalytic membranes with antifouling properties and alcohol stability can make biodiesel production more cost-effective and environmentally friendly.Article Citation - WoS: 1Citation - Scopus: 2A New-Generation Poly (ether Imide Sulfone) Based Solvent Resistant Ultrafiltration Membrane for a Sustainable Production of Silica Nanopowder(Elsevier, 2023) Güngörmüş, Elif; Alsoy Altınkaya, SacideThe work presented here demonstrated the feasibility of using a membrane to improve the sustainability of silica nanopowder production. Due to superior chemical resistance, high thermal-oxidative stability, and good processability, poly (ether imide sulfone) has been used for membrane production and modified with amine-functionalized TiO2 nanoparticles. The membrane demonstrated good long-term leaching stability in 40% ethanol and silica synthesis solution and maintained its permeability and rejection characteristics under static and dynamic conditions. Additionally, the high antifouling property of the membrane allowed recovering 99.5% of the nanoparticles. Backwashing with water resulted in a high flux recovery ratio (>93%), and gravity-settling without energy can easily separate silica nanoparticles and water in the backwashing solution. Compared to classical freeze-drying and oven-drying methods, integrating membrane into silica nanopowder production can reduce energy consumption by a factor of 81 and 53. At the same time, the utility cost can be saved by 80% and 69%. Additionally, the solvent and catalyst recovered in the permeate stream can be reused in the synthesis, reducing disposal and purchasing costs. In conclusion, membrane-assisted nanopowder production can minimize the adverse effects caused by commonly used conventional drying methods and make the process more sustainable and environmentally friendly.Article Citation - WoS: 12Citation - Scopus: 13Selected Persistent Organic Pollutants in Ambient Air in Turkey: Regional Sources and Controlling Factors(American Chemical Society, 2021) Güngörmüş, Elif; Sofuoğlu, Aysun; Çelik, Halil; Gedik, Kadir; Mulder, Marie D.; Lammel, Gerhard; Sofuoğlu, Sait CemilAs a result of its unique location, Turkey receives air masses from Europe, Russia, Middle East, and Africa, making it an important place in terms of long-range atmospheric transport (LRT) of contaminants. Atmospheric levels of 22 organochlorine pesticides (OCPs), 45 polychlorinated biphenyls (PCBs), and 14 polybrominated diphenyl ethers (PBDEs) were measured in two metropolitan cities, Istanbul and Izmir, on a weekly basis from May 2014 to May 2015. Dichlorodiphenyltrichloroethane (DDT) and its derivatives were dominant OCP species, followed by isomers of hexachlorocyclohexane (HCH) at both sites. The annual mean concentration of Sigma DDX (sum of o,p'-DDT, p,p'-DDT, o,p'-DDD, p,p'-DDD, o,p'-DDE, and p,p'-DDE) was 82 pg/m(3) for Istanbul and 89 pg/m(3) for Izmir, while these levels were about 46 pg/m(3) for Sigma HCHs (sum of alpha-, beta-, gamma-, and delta-HCH) at both of the sites. At both stations, tri- and tetra-PCBs and tetra- and penta-PBDEs were dominant congeners. The temperature dependence indicates that both LRT and local contaminated areas contribute to the elevated levels. A Lagrangian particle dispersion model (FLEXPART) showed a few potential source regions in northern Africa and Middle East, southern-southwestern and eastern Europe including Russia, as well as from local domestic metropolitan areas.Article Citation - WoS: 14Citation - Scopus: 16Facile Fabrication of Anti-Biofouling Polyaniline Ultrafiltration Membrane by Green Citric Acid Doping Process(Elsevier, 2021) Güngörmüş, Elif; Alsoy Altınkaya, SacideThis study aimed to enhance the anti-biofouling property of the polyaniline (PANI) based ultrafiltration (UF) membrane by utilizing its self-acid doping ability. A naturally derived biodegradable agent, citric acid, was doped to the membrane by filtering at 1 bar. Acid doping increased the hydrophilicity, made the surface nearly electroneutral, and imparted biocidal characteristics to the membrane. Biofouling was simulated by filtering a suspension of E.coli and S.aureus through the membranes. Most fouling on the doped membrane was reversible and easily removed by simple washing, leading to a high flux recovery ratio. The SEM images taken after filtration and washing steps showed that the modified membrane surface was free of bacteria while many bacteria accumulated on the pristine membrane surface. The doped membrane was stored in 1 M NaCl solution for up to five months. A tiny amount of citric acid was lost from the membrane, and at the end of storage, the flux, rejection, and antibacterial activity values did not change, demonstrating the antibacterial agent's stability. The protocol proposed in this study is fast, simple, facile, and easily scalable for large-scale production. Using a green antibacterial agent and its loading with a one-step process without consuming chemicals or functionalizing the support makes the proposed method environmentally friendly.Article Citation - WoS: 16Citation - Scopus: 16A High-Performance Acid-Resistant Polyaniline Based Ultrafiltration Membrane: Application in the Production of Aluminium Sulfate Powder From Alumina Sol(Elsevier, 2020) Güngörmüş, Elif; Alsoy Altınkaya, SacideIn this work, we report a new class of acid-resistant ultrafiltration membrane fabricated from polyaniline (PANI) based on its self-acid doping ability. The doped membrane was prepared by filtering the H2SO4 solution (pH = 0.55) through the PANI membrane at 2 bar. To critically assess the acid resistance, the resulting doped membrane was stored in H2SO4 solution (pH = 0.55) for one month. The chemical structure and separation performance of the membrane was not adversely affected by acid exposure. The membrane was also tested in realistic conditions through filtration of alumina sol synthesized in an extremely acidic H2SO4 solution. The results have shown that 99% recovery of the aluminium sulfate particles is possible with the doped PANI membrane as a result of the hydrophilic, relatively smooth, and antifouling surface created by acid doping. The membrane filtration did not change the size and size distribution of the particles in the sol. After filtration, concentrated particles were converted into powder form in 24 h at room temperature without using a dryer. The method proposed in this study is easy and robust and can be used to develop acid-resistant UF membranes not only for concentrating the alumina sol but also for recovering valuable compounds from acid-containing feeds.Article Citation - WoS: 91Citation - Scopus: 95Source Apportionment and Carcinogenic Risk Assessment of Passive Air Sampler-Derived Pahs and Pcbs in a Heavily Industrialized Region(Elsevier Ltd., 2018) Çetin, Banu; Yurdakul, Sema; Güngörmüş, Elif; Öztürk, Fatma; Sofuoğlu, Sait CemilCancer has become the primary reason of deaths in Dilovasi probably due to its location with unique topography under the influence of heavy industrialization and traffic. In this study, possible sources and carcinogenic health risks of PAHs and PCBs were investigated in Dilovasi region by Positive Matrix Factorization (PMF) and the USEPA approach, respectively. PAHs and PCBs were measured monthly for a whole year at 23 sampling sites using PUF disk passive samplers. Average ambient air concentrations were found as 285 ± 431 ng/m 3 and 4152 ± 6072 pg/m 3 , for Σ 15 PAH and Σ 41 PCB, respectively. PAH concentrations increased with decreasing temperature especially at urban sites, indicating the impact of residential heating in addition to industrial activities and traffic. On the other hand, PCB concentrations mostly increased with temperature probably due to enhanced volatilization from their sources. Possible sources of PAHs were found as emissions of diesel and gasoline vehicles, biomass and coal combustion, iron and steel industry, and unburned petroleum/petroleum products, whereas iron-steel production, coal and biomass burning, technical PCB mixtures, and industrial emissions were identified for PCBs. The mean carcinogenic risk associated with inhalation exposure to PAHs and PCBs were estimated to be >10 −6 and >10 −5 , respectively, at all sampling points, while the 95th percentile was >10 −5 at 15 of 23 and >10 −4 at 8 of 23 sampling locations, respectively. Probabilistic assessment showed, especially for PCBs, that a majority of Dilovasi population face significant health risks. The higher risks due to PCBs further indicated that PCBs and possibly other pollutants originating from the same sources such as PBDEs and PCNs may be an important issue for the region.Article Citation - WoS: 98Citation - Scopus: 118Organophosphate Ester (opes) Flame Retardants and Plasticizers in Air and Soil From a Highly Industrialized City in Turkey(Elsevier Ltd., 2018) Kurt Karakuş, Perihan Binnur; Alegria, Henry; Birgül, Aşkın; Güngörmüş, Elif; Jantunen, LiisaPassive air samples were collected at eight sites in Bursa, Turkey during five sampling periods between February–December 2014. Locations encompassed urban, suburban, industrial, rural and background environments. Soil samples (n = 8) were collected at each site during February 2014. Six OPEs were detected in samples: tris(2-chloroethyl) phosphate (TCEP), tris(chloropropyl) phosphate (TCPP), triphenyl phosphate (TPHP), tris(2-butoxyethyl) phosphate (TBOEP), tris(2-ethylhexyl) phosphate (TEHP), and tris(2-isopropylphenyl) phosphate (T2iPPP). Frequency of detection in air samples was TCPP and TPHP (100%) > TBOEP (88%) > TCEP (85%) > TEHP (78%) > T2iPPP (20%). Total OPEs in air per site by sampling period (excluding non-detects) ranged from 529 to 19,139 pg/m3. In soil, total OPEs ranged from 38 to 468 ng/g dw. In air, alkylated OPEs dominated followed by halogenated and aryl OPEs. In air, annual mean concentrations were TBOEP > TCPP > TPHP > T2iPPP > TEHP > TCEP. In soils, alkylated OPEs were dominant at six sites and chlorinated OPEs at two sites. A comparison of OPE profiles between air and soil suggests that soils may be partly a source of OPEs to air. Mean concentrations in air were not directly proportional to temperature, and there were differences between alkylated compared to halogenated and aryl OPEs. In air, total and alkylated OPEs levels were fairly uniform, whereas more variability was found for the halogenated and aryl compounds. The relative contribution to total OPEs decreases for alkylated OPEs and increases for halogenated OPEs in samples going from background to suburban to urban and industrial sites. Levels of individual OPEs were all positively correlated between air and soils. In air, correlations between individual compounds were weak to moderate and were only statistically significant for TBOEP and TPHP. In soils, correlations were generally stronger and statistically significant only for TPHP and T2iPPP.Article Citation - WoS: 45Citation - Scopus: 45The First Countrywide Monitoring of Selected Pops: Polychlorinated Biphenyls (pcbs), Polybrominated Diphenyl Ethers (pbdes) and Selected Organochlorine Pesticides (ocps) in the Atmosphere of Turkey(Elsevier Ltd., 2018) Kurt Karakuş, Perihan Binnur; Ugranlı Çiçek, Tuğba; Sofuoğlu, Sait Cemil; Çelik, Halil; Güngörmüş, Elif; Gedik, Kadir; Sofuoğlu, Aysun; Ökten, Hatice Eser; Birgül, Aşkın; Alegria, Henry; Jones, Kevin C.Atmospheric levels of 43 PCBs, 22 OCPs, and 14 PBDEs were determined in 16 cities at urban and rural sites by passive sampling to generate the first large-scale nationwide dataset of POP residues in Turkey's atmosphere. Sampling campaign was performed from May 2014 to April 2015 with three-month sampling periods at locations on east-west and north-south transects through the country to investigate seasonal and spatial variations, including long range atmospheric transport (LRAT). Factor analysis was conducted to infer on the potential sources. Overall average Σ43PCBs concentration was 108 ± 132 pg/m3. PCB-118 (26.3 ± 44.6 pg/m3) was the top congener, and penta-CBs had the highest contribution with 54.3%. ΣDDTs had the highest annual mean concentration with 134 ± 296 pg/m3 among the OCP groups among which the highest concentration compound was p'p-DDE (97.6 ± 236 pg/m3). Overall average concentration of Σ14PBDEs was 191 ± 329 pg/m3 with the highest contribution from BDE-190 (42%). Comparison of OCPs and PCBs concentrations detected at temperatures which were above and below annual average temperature indicated higher concentrations in the warmer periods, hence significance of secondary emissions for several OCPs and Σ43PCBs, as well as inference as LRAT from secondary emissions. The first nationwide POPs database constructed in this study, point to current use, local secondary emissions, and LRAT for different individual compounds, and indicate the need for regular monitoring. The first country-wide passive sampling of selected POPs showed no unequivocal trends reflecting transitional location of Turkey.Article Citation - WoS: 8Citation - Scopus: 9Indoor Air Quality in Chemical Laboratories(Elsevier Ltd., 2016) Ugranlı, Tuğba; Güngörmüş, Elif; Sofuoğlu, Aysun; Sofuoğlu, Sait CemilChemical laboratories are special microenvironments, in which many pollutants may be found because of the large range and number of chemicals that can be used, while concentrations of some specific ones may relatively be elevated due to high source strengths depending on the type and the number of experiments conducted and the number of people working in the laboratory. Laboratories can be considered as public places for the students whereas they are occupational microenvironments for their staff (technicians, specialists and teaching/research assistants). Hence, laboratory indoor air quality (IAQ) is of importance due to chronic, toxic and carcinogenic health risks for the staff in addition to possible acute effects for both staff and students. This chapter presents background information regarding pertinent indoor air pollutants, factors that determine their concentrations, indoor environmental comfort, a review of the literature on indoor environmental quality in chemical laboratories and measures of IAQ management.Article Citation - WoS: 108Citation - Scopus: 113Spatial and Seasonal Variations, Sources, Air-Soil Exchange, and Carcinogenic Risk Assessment for Pahs and Pcbs in Air and Soil of Kutahya, Turkey, the Province of Thermal Power Plants(Elsevier Ltd., 2017) Dumanoğlu, Yetkin; Gaga, Eftade O.; Güngörmüş, Elif; Sofuoğlu, Sait Cemil; Odabaşı, MustafaAtmospheric and concurrent soil samples were collected during winter and summer of 2014 at 41 sites in Kutahya, Turkey to investigate spatial and seasonal variations, sources, air-soil exchange, and associated carcinogenic risks of polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs). The highest atmospheric and soil concentrations were observed near power plants and residential areas, and the wintertime concentrations were generally higher than ones measured in summer. Spatial distribution of measured ambient concentrations and results of the factor analysis showed that the major contributing PAH sources in Kutahya region were the coal combustion for power generation and residential heating (48.9%), and diesel and gasoline exhaust emissions (47.3%) while the major PCB sources were the coal (thermal power plants and residential heating) and wood combustion (residential heating) (45.4%), and evaporative emissions from previously used technical PCB mixtures (34.7%). Results of fugacity fraction calculations indicated that the soil and atmosphere were not in equilibrium for most of the PAHs (88.0% in winter, 87.4% in summer) and PCBs (76.8% in winter, 83.8% in summer). For PAHs, deposition to the soil was the dominant mechanism in winter while in summer volatilization was equally important. For PCBs, volatilization dominated in summer while deposition was higher in winter. Cancer risks associated with inhalation and accidental soil ingestion of soil were also estimated. Generally, the estimated carcinogenic risks were below the acceptable risk level of 10− 6. The percentage of the population exceeding the acceptable risk level ranged from < 1% to 16%, except, 32% of the inhalation risk levels due to PAH exposure in winter at urban/industrial sites were > 10− 6.