Chemical Engineering / Kimya Mühendisliği

Permanent URI for this collectionhttps://hdl.handle.net/11147/14

Browse

Filters

2022 - 20244

Settings

Author: search.filters.author.Recepoğlu, Yaşar KemalPublication Index: search.filters.publicationIndex.PubMed

Search Results

Now showing 1 - 4 of 4
  • Article
    Citation - WoS: 4
    Citation - Scopus: 5
    Breakthrough Curve Analysis of Phosphorylated Hazelnut Shell Waste in Column Operation for Continuous Harvesting of Lithium From Water
    (Elsevier, 2024) Recepoğlu, Yaşar Kemal; Arar, Ozguer; Yuksel, Asli
    In batch-scale operations, biosorption employing phosphorylated hazelnut shell waste (FHS) revealed excellent lithium removal and recovery efficiency. Scaling up and implementing packed bed column systems necessitates further design and performance optimization. Lithium biosorption via FHS was investigated utilizing a continuous-flow packed-bed column operated under various flow rates and bed heights to remove Li to ultra-low levels and recover it. The Li biosorption capacity of the FHS column was unaffected by the bed height, however, when the flow rate was increased, the capacity of the FHS column decreased. The breakthrough time, exhaustion time, and uptake capacity of the column bed increased with increasing column bed height, whereas they decreased with increasing influent flow rate. At flow rates of 0.25, 0.5, and 1.0 mL/min, bed volumes (BVs, mL solution/mL biosorbent) at the breakthrough point were found to be 477, 369, and 347, respectively, with the required BVs for total saturation point of 941, 911, and 829, while the total capacity was calculated as 22.29, 20.07, and 17.69 mg Li/g sorbent. In the 1.0, 1.5, and 2.0 cm height columns filled with FHS, the breakthrough times were 282, 366, and 433 min, respectively, whereas the periods required for saturation were 781, 897, and 1033 min. The three conventional breakthrough models of the Thomas, Yoon-Nelson, and Modified Dose-Response (MDR) were used to properly estimate the whole breakthrough behavior of the FHS column and the characteristic model parameters. Li's extremely favorable separation utilizing FHS was evidenced by the steep S-shape of the breakthrough curves for both parameters flow rate and bed height. The reusability of FHS was demonstrated by operating the packed bed column in multi-cycle mode, with no appreciable loss in column performance.
  • Article
    Citation - WoS: 7
    Citation - Scopus: 7
    Cross-Linked Phosphorylated Cellulose as a Potential Sorbent for Lithium Extraction From Water: Dynamic Column Studies and Modeling
    (American Chemical Society, 2022) Recepoğlu, Yaşar Kemal; Yüksel, Aslı
    Phosphorylated functional cellulose was cross-linked with epichlorohydrin at different ratios because it is a very hydrophilic substance that instantly swells to form a hydrogel when it comes into contact with water. It was aimed to utilize a continuously packed bed column to recover lithium from water under varying operating conditions such as flow rate and bed height. The characterization results confirmed cross-linking based on morphology, structure, surface area, and thermal stability differences. Lithium recovery was more efficient with a low flow rate, but the dynamic sorption process was independent of bed height. The total capacities at the three flow rates with 1.5 cm bed height were 33.56, 30.15, and 25.54 mg g-1, and the total saturation times at the three different bed heights with 0.5 mL min-1 flow rate were 659, 1001, and 1007 min, respectively. Only 15.75 mL of 5% H2SO4 solution was required to desorb approximately 100% of Li from the saturated sorbent.
  • Article
    Citation - WoS: 31
    Citation - Scopus: 35
    Electrochemical Degradation of Methylene Blue by a Flexible Graphite Electrode: Techno-Economic Evaluation
    (American Chemical Society, 2022) Gören, Ayşegül Yağmur; Recepoğlu, Yaşar Kemal; Edebali, Özge; Şahin, Çağrı; Genişoğlu, Mesut; Ökten, Hatice Eser
    In this study, electrochemical removal of methylene blue (MB) from water using commercially available and low-cost flexible graphite was investigated. The operating conditions such as initial dye concentration, initial solution pH, electrolyte dose, electrical potential, and operating time were investigated. The Box-Behnken experimental design (BBD) was used to optimize the system's performance with the minimum number of tests possible, as well as to examine the independent variables' impact on the removal efficiency, energy consumption, operating cost, and effluent MB concentration. The electrical potential and electrolyte dosage both improved the MB removal efficiency, since increased electrical potential facilitated production of oxidizing agents and increase in electrolyte dosage translated into an increase in electrical current transfer. As expected, MB removal efficiency increased with longer operational periods. The combined effects of operating time-electrical potential and electrical potential-electrolyte concentration improved the MB removal efficiency. The maximum removal efficiency (99.9%) and lowest operating cost (0.012 $/m3) were obtained for initial pH 4, initial MB concentration 26.5 mg/L, electrolyte concentration 0.6 g/L, electrical potential 3 V, and operating time 30 min. The reaction kinetics was maximum for pH 5, and as the pH increased the reaction rates decreased. Consequent techno-economic assessment showed that electrochemical removal of MB using low-cost and versatile flexible graphite had a competitive advantage.
  • Article
    Citation - WoS: 56
    Citation - Scopus: 64
    Carbonaceous Materials for Removal and Recovery of Phosphate Species: Limitations, Successes and Future Improvement
    (Pergamon-Elsevier Science Ltd, 2022) Recepoğlu, Yaşar Kemal; Gören, Ayşegül Yağmur; Orooji, Yasin; Khataee, Alireza
    The carbonaceous materials have gained significant interest for the phosphorus species remediation and recovery in the last decade. Carbonaceous materials present many unique features, such as cost effective, availability, environmentally friendly, and high removal efficiency that make them a promising adsorbent. In this review, the recent application of carbonaceous materials including activated carbon (AC), graphene and graphene oxide (GO), lignin, carbon nanotubes (CNTs), and gC(3)N(4) for phosphate removal and recovery were comprehensively summarized. The kinetics and isotherm models, removal mechanisms, and effects of operating parameters are reported. The reusability, lifetime of carbonaceous materials, and impact of modification were also considered. The modified carbonaceous materials have significantly high phosphate adsorption capacity compared to unmodified adsorbents. Namely, MgO-functionalized lignin-based bio-charcoal exhibited a 906.8 mg g(-1) of capacity as the highest one among other reviewed materials. The modification of carbonaceous materials with various elements has been presented to improve the surface functional groups, surface area and charge, and pore volume and size. Among these loaded elements, iron has been effectively used to provide a prospect for magnetic recovery of the adsorbent as well as increase phosphate adsorption. Furthermore, the phosphate recovery methods, phosphate removal efficiency of carbonaceous materials, the limitations, important gaps in the literature, and future studies to enhance applicability of carbonaceous materials in real scale are also discussed.