Chemical Engineering / Kimya Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/14
Browse
61 results
Search Results
Now showing 1 - 10 of 61
Article Citation - WoS: 12Citation - Scopus: 12Biofouling-Resistant Ultrafiltration Membranes Via Codeposition of Dopamine and Cetyltrimethylammonium Bromide With Retained Size Selectivity and Water Flux(American Chemical Society, 2022) Cihanoğlu, Aydın; Schiffman, Jessica D.; Alsoy Altınkaya, SacideBiofouling is a serious problem in ultrafiltration (UF) membrane applications. Modifying the surface of membranes with low molecular weight, commercially available antibacterial chemistries is an excellent strategy to mitigate biofouling. Herein, we report a new strategy to impart antibacterial and anti-biofouling behavior without changing the support membrane’s size selectivity and pure water permeance (PWP). To this end, a strong antibacterial agent, cetyltrimethylammonium bromide (CTAB), was codeposited with dopamine onto commercial polyethersulfone (PES) UF membranes in the presence of nitrogen (N2) gas backflow. The PWP and pore size of the support membrane did not change with codeposition, confirming the benefit of N2 backflow in mitigating the solution intrusion phenomenon. X-ray photoelectron spectroscopy (XPS), surface ζ potentials, and contact angle measurements confirmed the successful codeposition of polydopamine (PDA) and CTAB onto the membrane. Among three different CTAB concentrations systematically investigated, the membrane functionalized with CTAB at the critical micelle concentration (CMC) provided the best anti-biofouling activity against Gram-positive (Staphylococcus aureus) and Gram-negative (Escherichia coli) bacteria and retained its surface ζ potential after being stored in 1 M NaCl (pH = 6.8) for 3 months. Our results demonstrate the potential of using a facile, one-step approach to modify commercial UF membranes without compromising their pore size or flux, while simultaneously endowing antibacterial activity.Article Citation - WoS: 16Citation - Scopus: 15Ultrasound-Assisted Dopamine Polymerization: Rapid and Oxidizing Agent-Free Polydopamine Coatings on Membrane Surfaces(Royal Society of Chemistry, 2021) Cihanoğlu, Aydın; Schiffman, Jessica D.; Alsoy Altınkaya, SacideHerein, we report a controllable pathway to accelerate the polymerization kinetics of dopamine using ultrasound as a trigger. The use of ultrasound was demonstrated to dramatically accelerate the slow liquid phase reaction kinetics and increase the deposition rate of the polydopamine coating on the surface of polymeric membranes.Article Citation - WoS: 54Citation - Scopus: 62A Positively Charged Loose Nanofiltration Membrane Fabricated Through Complexing of Alginate and Polyethyleneimine With Metal Ions on the Polyamideimide Support for Dye Desalination(Elsevier, 2021) Metecan, Ayşe; Cihanoğlu, Aydın; Alsoy Altınkaya, SacideNowadays, loose nanofiltration (NF) membranes are preferred for dye desalination to achieve high dye/salt selectivity and enable filtration at low operating pressure. However, current fabrication techniques require rigorous reaction conditions and long preparation times. Herein, we used the chelating ability of the polyethyleneimine (PEI) and alginate with the metal ions to fabricate loose NF membranes via a facile approach. The positively charged polyamide imide (PAI)/PEI support was used to build the assembly. Direct attachment of Zn or Fe ions to the PEI chains did not result in a stable complex in the presence of a high salt concentration (1000 ppm NaCl). On the other hand, alginate coated on the support allowed building permanent assemblies after crosslinked with Fe3+ and Zn2+ transition metal ions. The PAI/PEI-Alg-Fe3+ membrane exhibited the highest permeability, excellent antifouling behaviour upon exposure to synthetic textile wastewater, and maintained long-term stability under static and dynamic conditions. Also, the same membrane rejected dyes and coloured substances in real wastewater sample during 72 h continuous filtration. With alginate metal complex formation on a suitable support, a scalable loose NF membrane was manufactured, demonstrating improved throughput value compared to current NF membranes.Article Citation - WoS: 50Citation - Scopus: 51A Facile Route To the Preparation of Antibacterial Polysulfone-Sulfonated Polyethersulfone Ultrafiltration Membranes Using a Cationic Surfactant Cetyltrimethylammonium Bromide(Elsevier, 2020) Cihanoğlu, Aydın; Alsoy Altınkaya, SacideCetyltrimethylammonium bromide (CTAB), a cationic surfactant, is known to have strong bactericidal potential. In this study, we report a facile approach for preparing CTAB-containing polysulfone-sulfonated polyethersulfone (PSF-SPES) based ultrafiltration membranes with antibacterial properties. The CTAB was added in gelation medium at three different concentrations and made an electrostatic interaction with SPES at the polymer/bath interface during phase inversion. The successful incorporation of the CTAB in the membrane structure was confirmed by attenuated total reflectance Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. The CTAB-containing membranes had higher contact angle, lower pure water permeability (PWP) and molecular weight cut-off than the pristine membrane. The membranes prepared at critical and above critical micelle concentration (CMC) of the CTAB showed excellent antibacterial activity on both Gram-negative (Escherichia coli) and Gram-positive (Staphylococcus aureus) bacteria. On the other hand, the PWP of the membrane decreased from 93 +/- 1.6 to 39.3 +/- 3.2 L/m(2) h bar upon increasing the CTAB concentration from 10(-3) M (=CMC) to 10(-2) M, consequently, CMC was chosen as the optimal concentration. The membrane prepared at the CMC displayed almost 100% flux recoveries after dynamic bacteria filtration followed by simple rinsing with PBS solution. Leaching experiments continued up to 30 days demonstrated that 96% of the CTAB remained in this membrane. Furthermore, at the end of 1 month of storage in 1 M NaCl solution, no change was observed in the antibacterial activity of this membrane compared to fresh membrane. These findings emphasize the potential of the facile approach proposed in this study to develop antibacterial ultrafiltration membranes in a single step.Article Payne Cell Gravimetric Measurements in Polymer-Solvent Systems for Diffusion Coefficients and Isotherm Data(Wiley, 2021) Zielinski, John M.; Garcia, Armando R.; Alsoy Altınkaya, SacideThe discussion focuses on the application of a Payne cell to the measurement of diffusion and solubility coefficients in polymer/solvent systems. Payne cells have, thus far, been used exclusively to measure steady-state permeation rates of solvents. An analytical model has been developed to describe transient gravimetric sorption and desorption measurements performed with a Payne cell. The model has been validated by a complementary numerical simulation and has been applied to evaluate diffusion and solubility coefficients in two different toluene-silicone rubber systems. The data measured using the Payne cell are found to compare very well with diffusion coefficient and isotherm data measured by traditional gravimetric sorption experiments.Article Jelatin Doku İskelesinin Mekanik Özellikleri Üzerine Gözenek Oluşturucu Ajanın Boyutu ve Bağlantı Süresinin Etkileri(Manisa Celâl Bayar Üniversitesi, 2015) Büyüköz, Melda; Alsoy Altınkaya, SacideBu çalışmada, makrogözenekli ve gözenekleri birbirleri ile bağlantılı olarak kalıplama, ısı etkili faz ayrımı ve tanecik uzaklaştırma yöntemleri ile üretilen jelatin bazlı doku iskelelerinde gözenek oluşturucu ajan olan parafin kürelerin boyutu ve bağlantı sürelerinin doku iskelelerinin mekanik özellikleri üzerine olan etkileri incelenmiştir. Sünger formlu ve açık hücreli yapıda olan doku iskelelerinin mekanik özellikleri sıkıştırma testi ile ölçülmüştür. Yapılan ölçümler parafin küre çapındaki artışın doku iskelelerinin sıkıştırma katsayısını istatistiksel olarak anlamlı bir şekilde etkilemediğini göstermiştir. Ancak, parafin kürelerin maruz bırakıldığı ısı etkileşim süresinin 100 dakikadan 400 dakikaya arttırılmasının 250-425 µm çapındaki parafin kürelerle hazırlanan doku iskelesinin elastisite değerini arttırdığı belirlenmiştir (p<0.05). Ayrıca, 425-600 µm çapındaki parafin kürelerle hazırlanan doku iskelelerinde, ısı etkileşim süresi 100 dakikadan 400 dakikaya arttırıldığında sıkıştırma katsayısı anlamlı bir şekilde azalmıştır (p<0.05). Elde edilen sonuçlar, bu tür doku iskelelerinde parafin kürelerin boyutundan çok bağlantı süresinin mekanik özellikler üzerinde etkili olduğunu göstermiştirConference Object Predicting Drying in Solvent-Coated Polymeric Films(American Chemical Society, 2000) Alsoy Altınkaya, Sacide; Duda, John Larry[No abstract available]Conference Object Development of Functional Materials for Sirna Delivery and Neural Tissue Engineering(AIChE, 2015) Uz, Metin; Alsoy Altınkaya, Sacide; Mallapragada, Surya K.The current nonviral siRNA delivery systems in the literature face many problems such as, cellular entry, endosomal escape and efficient siRNA release. Considering this motive, we developed gold nanoparticles (AuNPs) and temperature/pH responsive pentablock copolymer based siRNA delivery systems to address these problems. The temperature and pH responsive cationic and amphiphilic pentablock copolymers, which were consisted of the temperature responsive Pluronic F127 middle block constructed by PEO-PPO-PEO ((poly(ethyleneoxide)-block-poly(propyleneoxide)-block-poly(ethyleneoxide))) blocks contributing cellular entry through temperature responsive micellization and pH responsive cationic PDEAEM (poly(2-diethylaminoethyl methacrylate)) end blocks facilitating nucleic acid condensation and endosomal escape, were used for the first time in the development of polyplex and AuNP based multicomponent siRNA delivery systems (MCSs). The results indicated that systems managed to protect siRNA from external effects, maintain the system stability, facilitate cellular entry and enhance endosomal escape. It was noted that the transfection efficiency of the MCSs, which were boosted by the presence of cleavable disulfide bond, was ~15% higher than the commercial product RNAiMax while the efficacy of polyplexes alone were similar to the RNAiMax.Book Citation - Scopus: 5Editors’ Foreword(CRC Press, 2017) Figoli, A.; Hoinkis, Jan; Altinkaya, Sacide Alsoy; Bundschuh, JochenThe book focuses on Application of Nanotechnology in Membranes for Water Treatment but not only provides a series of innovative solutions for water reclamation through advanced membrane technology but also serves as a medium to promote international cooperation and networking for the development of advanced membrane technology for Universal well-being and to achieve the common goal of supplying economically, environmentally and societally sustainable freshwater and better sanitation systems. This book is unique because the chapters were authored by established researchers all around the globe based on their recent research findings. In addition, this book provides a holistic coverage of membrane development for water treatment, from the membrane preparation and characterizations to the performance for specific processes and applications. Since that water scarcity has become a global risk and one of the most serious challenges for the scientific community in this century, the publication of this book is therefore significant as it will serve as a medium for a good reference of an alternative solution in water reclamation. This book will provide the readers with a thorough understanding of the different available approaches for manufacturing membranes both with innovative polymeric systems and inorganic nano-materials which could give enhanced functionalities, catalytic and antimicrobial activities to improve the performance of the existing membranes. It will be useful for leading decision and policy makers, water sector representatives and administrators, policy makers from the governments, business leaders, business houses in water treatment, and engineers/ scientists from both industrialized and developing countries as well. © 2019 Elsevier B.V., All rights reserved.Article Citation - WoS: 28Citation - Scopus: 29Development of a High-Flux Thin-Film Composite Nanofiltration Membrane With Sub-Nanometer Selectivity Using a Ph and Temperature-Responsive Pentablock Co-Polymer(American Chemical Society, 2019) Bar, Canbike; Çağlar, Nagahan; Uz, Metin; Mallapragada, Surya K.; Alsoy Altınkaya, SacideProducing block co-polymer-based nanofiltration (NF) membranes with sharp molecular weight cutoffs via an efficient method exhibiting persistent size-based separation quality is challenging. In this study, this challenge was addressed by reporting a facile approach to fabricate pentablock co-polymer (PBC)-based thin-film composite (TFC) NF membranes. The PBC, consisting of temperature-responsive Pluronic F127 (PEO-b-PPO-b-PEO) middle blocks and pH-responsive poly(N,N-(diethylamino)ethyl methacrylate) end blocks, were synthesized by atom-transfer radical polymerization. This polymer was then attached electrostatically to the surface of polysulfone/sulfonated polyether-sulfone support membranes fabricated using a non-solvent-induced phase separation technique. The conformational changes of the PBC chains in response to pH and temperature determined the, pure water flux and neutral solute (PEG 1000) rejection performance of TFC membranes. Permeability of the membranes increased from 13.0 +/- 0.63 to 15.9 +/- 0.06 L/m(2).h bar and from 6.7 +/- 0.00 to 13.9 +/- 0.07 L/m(2).h.bar by changing the solution pH from 4 to 8.5 and temperature from 4 to 25 degrees C, respectively. The pH- and temperature-responsive conformational changes did not affect the PEG 1000 rejection and membrane pore radius, which remained constant at similar to 89% and similar to 0.9 nm, respectively. This important finding was attributed to the high grafting density of co-polymer chains, resulting in spatial limitations among the grafted chains. The pore size of similar to 0.9 nm achieved with the proposed membrane design is the smallest size reported so far for membranes fabricated from block copolymers. TFC membranes demonstrated high stability and maintained their flux and rejection values under both static (storage in an acidic solution for up to 1 month) and dynamic (filtering PEG 1000 solution over 1 week) conditions. Pentablock copolymers enable a NF membrane with a sharp molecular weight cutoff suitable for size-selective separations. The membrane fabrication technique proposed in this study is a scalable and promising alternative that does not involve complex synthetic routes.